What is the reason why an Aoling diesel vehicle cannot accelerate when the throttle is pressed?

1 Answers
DeRosalie
07/30/25 7:12am
Aoling diesel vehicle cannot accelerate when the throttle is pressed due to a fault in the engine's fuel supply system, such as non-compliant fuel pressure, injection quantity, ignition timing, faulty spark plugs and high-voltage wires, or excessive clutch gap, requiring replacement of related parts. Aoling: Aoling light trucks are equipped with Cummins, 4JBTDi power, Lovol 4D power, Yangchai, Chaochai diesel engines, and Yunnei pure CNG power. The wheelbase ranges from 2.49-5.6 meters, the load capacity from 0.75-10 tons, and the cargo compartment length from 3-7.8 meters, making it the brand with the most diverse and comprehensive power options in the mid-to-high-end light truck market. Diesel Vehicle: A diesel vehicle refers to a vehicle powered by diesel fuel, equipped with a diesel engine that burns diesel to obtain energy release.
Was this review help?
20
3
Share
More Forum Discussions

What is the fuel tank capacity of Jinbei in liters?

The fuel tank capacity of Jinbei is 55 liters. A fuel tank is a container for storing fuel in aircraft or automobiles, and it is also a specialized container for storing hydraulic oil or hydraulic fluid in hydraulic systems. Fuel tanks can be divided into two types: open tanks and closed tanks. Taking the Jinbei Haishi 2020 2.0L Classic Luxury High Roof National VI 1TZS as an example: it is equipped with a 5-speed manual transmission, has a mid-engine rear-wheel drive layout, and uses hydraulic power steering. The dimensions of the Jinbei Haishi 2020 2.0L Classic Luxury High Roof National VI 1TZS are 5020mm in length, 1690mm in width, and 2225mm in height, with a wheelbase of 2590mm. It features a naturally aspirated intake system, a maximum torque of 185 Nm, and a torque range of 2800 to 4000 rpm. The tire specification is 195/70R15.
16
4
Share

What causes the car to shake at low speeds but not at high speeds?

The shaking of the car at low speeds is caused by loose tie rod ends, and adjusting the tightness can solve the problem. Here are specific details about tie rod ends: Working principle: The working principle of tie rod ends involves a rod with a ball joint housing, where the ball joint of the steering spindle is placed inside the ball joint housing. The ball joint is hinged with the edge of the shaft hole of the ball joint housing through the ball joint seat at its front end. The needle roller between the ball joint seat and the steering spindle is embedded in the groove on the inner hole surface of the ball joint seat. This design helps reduce ball joint wear and improves the spindle's tensile resistance. Damage to the ball joint: A damaged tie rod end can cause steering wheel vibration, brake deviation, and steering failure. In severe cases, the wheel may suddenly swing sideways or even detach due to the ball joint falling off, leading to serious consequences.
5
0
Share

Why are there fewer buyers for the imported Tiguan?

There are fewer buyers for the imported Tiguan due to its lack of price advantage. Below are the specific details of the imported Tiguan: 1. Safety Features: The Tiguan comes standard with side airbags + knee airbags, electronic stability control, electronic differential lock, collision safety + low-speed braking, lane keeping assist, auto hold, tire pressure monitoring, fatigue warning system, and cruise control. The 330TSI Comfortline and higher models add hill descent control to the above features. The two top-tier models are also equipped with blind spot monitoring + lane change assist + rear traffic alert, parking assist, and rearview camera. 2. Powertrain: It is equipped with 1.4T and 2.0T low/high-power engines, corresponding to the 280TSI, 330TSI, and 380TSI model badges, with maximum output power of 150 horsepower, 180 horsepower, and 220 horsepower respectively. The transmission system is matched with a 6-speed wet dual-clutch transmission (1.4T models) and a 7-speed wet dual-clutch transmission (2.0T models). The three 2.0T models also come standard with the 4MOTION all-wheel-drive system.
5
1
Share

What to Do When the Reversing Camera Image is Blurry Due to Glare?

To address glare on the reversing camera, you can increase the brightness or use a sunshade. Below are some related tips for reversing cameras: 1. Not Waterproof: Most reversing cameras on the market are waterproof. However, if you purchase a low-quality camera, it may allow water to seep in, causing blurry images. If the waterproof performance is insufficient, you can remove the camera, apply some sealant, or directly replace it with a higher-quality one. 2. Low Pixel: A low-pixel camera can result in a blurry display on the reversing camera screen. The camera's own clarity affects the display resolution. Consider replacing it with a higher-resolution reversing camera, preferably one with night vision capabilities, as it provides better imaging under the same lighting conditions. 3. Prolonged Use: If the reversing camera has been used for an extended period, the chip's light sensitivity may degrade. In this case, simply replace the reversing camera with a new one.
10
0
Share

Are Chery Cars China 5 or China 6 Vehicles?

Chery cars include both China 5 and China 6 vehicles. If you are buying a car now and do not plan to use it for a long time, purchasing a China 5 vehicle is acceptable since they are currently cheaper. However, if you intend to use the car for an extended period, it is advisable to buy a China 6 vehicle. The emission standards for China 5 and China 6 differ: The China 6 emission standard is the sixth-stage national standard for motor vehicle pollutant emissions. The China 5 emission standard, also known as "China 5 Standard," has an emission control level equivalent to the European Union's fifth-stage emission standard currently in effect. Introduction to Chery: Chery Automobile Co., Ltd. was established on January 8, 1997. It is one of the most representative independent brand automobile companies that grew through independent innovation after China's reform and opening-up.
12
1
Share

How to Take the Subject 3 Test with a Temporary ID Card Without Magnetic Stripe?

You can still take the Subject 3 test without a magnetic stripe on your ID card. According to the regulations for applying for and using a driver's license, as long as you hold valid identification, you are eligible to take the test. Both a regular resident ID card and a temporary resident ID card are generally considered valid forms of identification and hold the same legal effect. Below is additional information: 1. You cannot practice for the Subject 3 test in a private car: During the Subject 3 test process, you are only allowed to practice using the driving school's vehicles. Before obtaining a driver's license, you are not permitted to drive any other vehicles except those provided by the driving school. Violating this rule will result in penalties for driving without a license, so this point must be clearly understood. 2. Registering for Subject 4: After passing the Subject 3 test, you can schedule the Subject 4 test. If time permits, you can complete it on the same day. Upon passing the Subject 4 test, you will receive your driver's license, allowing you to legally drive a car. This is a lawful process, and the driver's license is a legally recognized document, so you can use it without any concerns.
7
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.