What is the reason for water under the foot mats of the Bora?

What is the actual measured ground clearance of the CRV?

" The ground clearance of the CRV is 135 millimeters. The ground clearance of the CRV refers to the distance between the lowest point (excluding the wheels) and the supporting plane, which indicates the vehicle's ability to pass over obstacles such as stones and tree stumps without collision. The higher the ground clearance of the CRV, the better its off-road capability. However, if the ground clearance is too high, the stability at high speeds may decrease. The design of the CRV began in 2008, with dimensions of 4621 millimeters in length, 1855 millimeters in width, and 1689 millimeters in height, and a wheelbase of 2660 millimeters. Generally, the ground clearance of sedans ranges between 110 millimeters and 150 millimeters, while SUVs have a ground clearance between 200 millimeters and 250 millimeters. However, the ground clearance of the CRV is not static; it also depends on the load condition. Therefore, changes in ground clearance should be considered based on the CRV's load variations. When selecting a vehicle, ground clearance can be one of the reference factors. The choice should depend on the vehicle's intended use and the road conditions. For urban areas with well-maintained roads, a vehicle with lower ground clearance can enhance stability and comfort. If the vehicle is frequently used in remote areas or on poor road conditions, a higher ground clearance may be preferable to avoid scraping or damaging the undercarriage, considering the vehicle's off-road performance. "

18

3

Share

What is the purpose of automotive urea?

Automotive urea solution can reduce harmful nitrogen oxides in exhaust gases into nitrogen and water, thereby decreasing the level of exhaust pollution. Below is a related introduction to automotive urea solution: 1. Function: Automotive urea solution is used to reduce nitrogen oxide compounds in vehicle exhaust, lowering the degree of exhaust pollution. 2. Composition: Automotive urea solution is a colorless, transparent, and clear liquid, a urea-based chemical reactant, formulated from high-purity urea without any additives and pure water, with a urea content of 32.5% (mass fraction) in the solution. 3. Significance: Automotive urea solution is key to reducing pollutant emissions from diesel vehicles. Applying automotive urea solution in the SCR (Selective Catalytic Reduction) system is crucial for engine exhaust emissions to meet National IV and higher emission standards.

9

2

Share

What Does Regular Car Maintenance Include?

Regular car maintenance includes: 1. Changing engine oil and oil filter, cleaning the air filter; 2. Checking whether the coolant level is normal; 3. Inspecting the car's brakes and chassis components for any scratches; 4. Checking the power steering fluid level and the condition of all oil pipe connections; 5. Examining the generator, air conditioning, water pump, and belt for signs of aging; 6. Checking tire pressure and wear condition. Below is relevant information about regular car maintenance: 1. Purpose of regular maintenance: The main goal of regular car maintenance is to keep the car clean and in good technical condition, eliminate potential hazards, prevent accidents, slow down the aging process of car components, extend their service life, and ensure the car operates properly. 2. Types of regular maintenance: Regular car maintenance is divided into three levels: primary maintenance, secondary maintenance, and tertiary maintenance. Typically, a car should undergo primary maintenance every 2,000-3,000 kilometers. After driving 10,000-15,000 kilometers, secondary maintenance is required, which must be performed by professional mechanics.

14

4

Share

How to Solve the Problem of Strong Odor in Old Cars?

Here are some methods to solve the problem of strong odor in old cars: 1. Use car perfume: Some car perfumes can capture odor molecules with their unique properties and purify the air through decomposition. 2. Use bamboo charcoal bags for cars: Activated charcoal contains a large number of irregular pores, among which the pores similar in size to formaldehyde molecules will adsorb formaldehyde, thereby purifying the air. However, the number of internal pores is limited, and when adsorption becomes saturated, it may cause secondary pollution. Therefore, it is necessary to replace them regularly. 3. Install a car air purifier: A car air purifier can filter polluted air. 4. Ventilate frequently by opening windows: Simply opening the windows allows fresh air to enter the car, diluting and purifying formaldehyde.

13

4

Share

Can You Keep Driving for a While If One of the Four Cylinders Has Insufficient Compression?

If one of the four cylinders has insufficient compression, you can continue driving for a short while, but you should get to a repair shop as soon as possible. Otherwise, it may easily damage the engine. Below is extended knowledge on the causes of insufficient cylinder compression: 1. Excessive wear of the cylinder or piston rings, misalignment, seizure, or breakage of piston rings can lead to insufficient cylinder compression. Prolonged exposure to high temperatures can reduce the elasticity of piston rings, preventing them from sealing the piston properly, which also results in insufficient compression. 2. Damage or poor sealing of the cylinder head gasket can cause insufficient cylinder compression. The cylinder head gasket serves to isolate the cylinders from each other. If the gasket between adjacent cylinders is damaged, it can lead to gas leakage between the cylinders, resulting in low pressure in both adjacent cylinders. 3. Warping of the cylinder head's lower surface can cause insufficient cylinder compression. High engine coolant temperatures can deform the cylinder head, causing it to lose flatness and leading to poor sealing. This will show up as insufficient compression during a compression test. Most cases of low compression across all or multiple cylinders are due to this reason. 4. Poor sealing of the intake or exhaust valves can result in insufficient cylinder compression. Valve cone surface erosion, bent or broken valves, or improper valve clearance adjustment can all lead to poor cylinder sealing and insufficient compression.

13

0

Share

Should You Use Recirculation or Fresh Air Mode When Driving in Summer?

First, use the fresh air mode or open the windows for ventilation, then switch to recirculation mode. Here is some extended knowledge: The difference between car recirculation and fresh air modes: 1. Car recirculation mode circulates the air inside the vehicle in a closed loop, indicated by an arrow symbol inside a closed car icon; whereas fresh air mode draws outside air into the cabin, indicated by an arrow from outside pointing into a closed car icon. 2. Car recirculation mode means the air inside the vehicle is heated or cooled before being recirculated; fresh air mode means outside air is heated or cooled before being brought into the cabin, effectively exchanging air between the inside and outside of the vehicle. 3. Typically, whether using heating or cooling, it's best to start with recirculation mode. However, prolonged use of recirculation can lead to increased carbon dioxide levels from passengers' exhalation. Therefore, it's advisable to switch to fresh air mode every hour to refresh the air inside the cabin.

6

0

Share

What is the reason for water under the foot mats of the Bora?

What is the actual measured ground clearance of the CRV?

What is the purpose of automotive urea?

What Does Regular Car Maintenance Include?

How to Solve the Problem of Strong Odor in Old Cars?

Can You Keep Driving for a While If One of the Four Cylinders Has Insufficient Compression?

Should You Use Recirculation or Fresh Air Mode When Driving in Summer?

What type of engine oil is suitable for the Arrizo 5?

What does auto-stop mean?

What documents are required for the 2-year vehicle inspection?

What Do the Specifications on Tires Represent?