What is the reason for the Peugeot 3008 fan running at high speed continuously?

What is the matching standard between gear shifting and speed?

Different gears are suitable for different speeds. Here are the detailed explanations: 1. Gear matching standards: (1) 1st gear: Used for normal starting or climbing very steep slopes, with a speed generally around 10km/h; (2) 2nd gear: A transitional gear for acceleration after starting or for low-speed driving, with a speed generally around 20km/h; (3) 3rd gear: Used when the speed is between 20-40km/h, commonly used for urban driving; (4) 4th gear: Used when the speed is between 40-60km/h; (5) 5th gear: Can be used when the speed reaches 60km/h. 2. Precautions: The most important thing when driving a manual transmission car is to master the timing of gear shifting. The upshift sequence must be 1st gear → 2nd gear → 3rd gear → 4th gear → 5th gear, and skipping gears is not recommended. The downshift sequence depends on the speed, and generally, when the engine speed is below around 1500 rpm, you should downshift according to your car's condition.

4

1

Share

What is the fault when the EPC light comes on in S gear?

EPC light on indicates a fault in the engine electronic control system. Focus on checking the wiring, electronic throttle, and engine computer. It is recommended to go to a repair station for inspection. Generally, there are two possibilities when the EPC light comes on. One is a dirty throttle, which should be cleaned. The other situation is that the brake light is not working, and the brake switch and wiring need to be checked. Here is some extended information: 1. Yellow warning light: The yellow warning light on a car indicates a warning, suggesting that some systems in the car may have parameters exceeding the standard, which are different from the initially set parameters. The yellow light indicates that this is not a very urgent fault. When the car's driving computer detects an abnormal signal and the yellow warning light comes on, the system will handle it on its own. 2. Red warning light: The red warning light will affect driving safety. If the red warning light comes on, it will directly affect the car's core components or driving safety. At this time, you should pay attention to stopping the car, then check the car's fault, and solve the fault before driving on the road.

15

2

Share

Does Rain Affect a Newly Applied Color Change Film?

Rain can affect a newly applied color change film. Here is an introduction regarding whether rain affects a newly applied color change film: 1. Reasons: Avoid getting the film wet within the first three days after application and try to refrain from washing the car to prevent the film from peeling off due to moisture. Also, avoid turning on the rear window defogger for a week, as moisture can negatively impact the defogger lines. After installation, you can use a wet towel, sponge, or soft cloth to clean the film surface. Additionally, you may notice a foggy appearance caused by water vapor inside the film after application. This is a normal phenomenon during the drying process of the sun film and will gradually disappear over time. 2. Identifying the Quality of Color Change Film: (1) Car owners should fully understand the price range of color change films in the market to avoid being deceived. (2) High-quality color change films have rich, uniform colors, while inferior ones appear uneven with a noticeable grainy texture. (3) The thickness and toughness of the backing paper are directly proportional to the quality of the color change film. (4) If a strong, irritating odor is detected upon close inspection, it is likely an inferior product. High-quality color change films typically adhere to global environmental standards. (5) The adhesive on high-quality color change films maintains strong adhesion even after multiple applications, whereas inferior films show a significant decrease in adhesive strength after just one or two uses.

18

2

Share

Why Does a Brand New Car Have a Burnt Smell?

It is normal for a brand new car to have a burnt smell. Here are some explanations regarding the burnt smell in a new car: 1. Reasons: Many parts of a car operate at high temperatures during use. Some plastic and other material components in a new car may emit odors under high heat, which will dissipate over time. However, during the break-in period, it is important to avoid sudden acceleration and keep the engine RPM within a reasonable range. 2. Other related reasons: (1) If the smell resembles burning plastic, it is likely caused by overheating electrical wiring. Burnt wires are usually accompanied by localized heat or smoke. With careful inspection, the source of the issue can be identified. If the wiring is overheating, the car must be stopped immediately to determine the cause. Although the smell of burnt wiring may not be strong, the risk is significant. Failure to detect it promptly can lead to circuit damage, engine seizure, or even a vehicle fire. (2) If you consistently smell unburned gasoline while driving, you must stop and check for fuel leaks and their severity before continuing. Both fuel-injected and carbureted vehicles may experience aging and cracking in fuel lines after prolonged use. Under slight vibration or changes in line pressure, fuel may leak from these areas. (3) Electrical issues, such as short circuits, aging wires, or excessive load, can also cause a burnt smell. The wiring may burn out shortly afterward. However, such problems are unlikely in a brand new car, so this possibility can be ruled out.

20

3

Share

Is it normal for newly applied car window film to appear blurry?

It is normal for a car with newly installed window film to have some moisture visible immediately after application. Below is an explanation about the blurriness of newly applied car window film: 1. Principle: It is common to experience this situation within 7 days of film application. This occurs because water is used during the installation process, leaving some moisture trapped under the film. As the moisture gradually dries, the film will become increasingly clear. If the blurriness persists after 7 days, it is advisable to consult the installation shop, as it may be due to installation issues or the quality of the film itself. 2. Causes: (1) Poor clarity of the film itself: Clarity and light transmittance are not entirely equivalent. Some films with high light transmittance may still cause visual distortion. The clarity of car window film depends on the material and manufacturing process, such as V-KOOL's optical PET base material, multiple precious metals, and molecular-level magnetron sputtering technology. (2) Scratches or corrosion during use: Although car window film is applied to the interior of the car, operations like rolling the windows up and down or cleaning the glass can easily scratch or damage the film. Once damaged, the film's clarity will naturally decrease. Therefore, when cleaning the glass, it is recommended to use non-corrosive cleaning solutions and soft, grit-free towels for wiping. Additionally, for car models with narrow gaps in the side windows, avoid applying overly thick security films. Instead, opt for car window films with excellent scratch-resistant coatings.

19

5

Share

What is the reason for not being able to shift gears?

The reasons for not being able to shift gears: internal failure of the gear lever assembly; failure of the P-gear lock solenoid valve inside the gear lever, or failure of the brake switch. Here is some additional information: 1. Gear shifting: Gear shifting refers to the transmission, which is used to change the torque and speed of the engine crankshaft to meet the different requirements of traction force and speed for driving wheels under various driving conditions such as starting, accelerating, driving, and overcoming road obstacles. 2. Function: Gear shifting allows the car to drive at a very low and stable speed, which is difficult to achieve solely by the minimum stable speed of the internal combustion engine. The reverse gear of the transmission enables the car to move backward, and its neutral gear allows the engine to be separated from the transmission system for a long time when starting the engine, parking, or coasting.

19

3

Share

What is the reason for the Peugeot 3008 fan running at high speed continuously?

What is the matching standard between gear shifting and speed?

What is the fault when the EPC light comes on in S gear?

Does Rain Affect a Newly Applied Color Change Film?

Why Does a Brand New Car Have a Burnt Smell?

Is it normal for newly applied car window film to appear blurry?

What is the reason for not being able to shift gears?

What Causes the Malfunction Light to Flash and the Car to Shake?

What kind of vehicle has a license plate starting with 'la'?

How to adjust the steering force level of Volvo S60?

What brand is sunfull tire?