What is the reason for the malfunction of the Mercedes-Benz C-class co-pilot window?

1 Answers
VanIvan
07/29/25 12:05pm
Reasons for the malfunction of the co-pilot window lift: circuit failure; deformation or damage of the glass mud slot; loose screws of the lift; damage to the window lift; deviation in the installation position of the guide rail. The recovery methods are introduced as follows: Recovery methods: You can try disconnecting the power supply and reconnecting it to see if it recovers. In addition, you can also inspect the circuit; clean or replace the glass; replace the window lift. Precautions: To prevent rainwater from flowing in, there is a rubber strip on the interior window frame. After the glass is soiled, the friction with the rubber strip increases, and the switch will also be affected, so the glass needs to be kept clean frequently. Small cards are often inserted into the window gaps. If not handled properly, the cards may fall into the door along the window. The internal structure of the door is complex, and the falling of the cards into the door can cause a series of chain reactions, such as damage to the window lift, door malfunction, and blockage of the drainage port.
Was this review help?
20
0
Share
More Forum Discussions

How to Remove the GLC Wiper Blade?

Lift the wiper blade upright and use a small flat-head screwdriver to pry the four clips outward. Once all four clips are lifted, remove the wiper blade. Take off the old rubber strip, install the new one, and after installing the wiper strip, slide the clips up and down until they click into the removal position.
7
3
Share

How to Turn Off the Seat Belt Beeping Sound?

The seat belt reminder sound cannot be turned off with a button. The sound will disappear once the seat belt is properly fastened. Fasten the seat belt or insert a seat belt buckle. If someone is sitting in the seat, the seat belt must be fastened.
19
5
Share

Car Washing Steps?

The first step in full vehicle cleaning is rinsing. There are generally two methods for body scrubbing: manual scrubbing method and mechanical scrubbing method. Re-rinsing involves rinsing the vehicle body again after scrubbing to clean the body. Two operators each hold a semi-wet large towel and wipe the entire vehicle from top to bottom, front to back.
3
5
Share

What Causes Slow Clutch Return?

Slow clutch return is caused by a blockage in the return oil hole of the clutch oil pump. Below is a detailed introduction to automotive clutches: 1. Causes of clutch failure: Typically, it starts with excessive wear of the clutch plate and ends with engine idling and clutch damage. Therefore, the key to addressing this issue lies in assessing the wear stage and damage level to prevent further deterioration. 2. Clutch maintenance methods: Reduce the frequency and duration of half-clutch engagement. Unlike dual-clutch transmissions, manual transmissions allow full control over the frequency and duration of half-clutch engagement, thereby minimizing clutch wear. For dual-clutch transmissions, most wear occurs during low-speed driving. Thus, mastering manual mode during low-speed phases can extend the clutch's service life.
4
0
Share

What is the difference between 8j and 9j wheel hubs?

The following are the specific differences between 8j and 9j wheel hubs: 1. In terms of model: 8 inches means the wheel hub is 18 inches and needs to be used with 18-inch tires. 8j refers to the tire width of 8 inches. 9j refers to the tire width of 9 inches. 8j and 9j mainly refer to the width of the wheel hub. Although both are 18 inches, the tire widths are different. 2. In terms of tire usage: The 8j wheel hub is most suitable for installing 225-width tires; the 9j wheel hub is most suitable for installing 245-width tires. For balanced tire performance, it is best to choose the optimal tire width corresponding to the wheel hub.
4
3
Share

How to Check the Subject 2 Test Results?

After completing the Subject 2 field test, you need to sign your name to confirm the results. The score sheet will display your Subject 2 test scores. Log in to the official website of the Traffic Safety Comprehensive Service Management Platform, select your province, click on personal login, enter your information, and log in. Once in your personal main interface, navigate to the student information section and find the exam information. Click on it to view the Subject 2 test details you wish to check.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.