What is the reason for the HOWO truck not shutting off after turning the key?

What to Do When the Car Door Handle Freezes?

If the car door handle is frozen and it's convenient, you can use a long extension cord to connect a household hairdryer to melt the ice on the door handle. Alternatively, you can use warm water to rinse off the ice on the car door. During winter when temperatures are low, it is recommended not to park the car outdoors. If there is accumulated water in the door gaps, it is very likely to freeze. After the car door handle is frozen, do not use brute force to open the door, as this can damage the door handle and potentially harm components like the door handle lock.

11

0

Share

What is the correct method for installing license plate screws?

Here is an introduction to the method for installing license plate screws: First, screw the screw rod into the screw hole at the license plate installation position to check if all the screw holes are basically normal. After inspecting the screw holes, pre-assemble each set of screws in the following order from top to bottom: screw rod, anti-theft cap, and washer. The hexagonal screw cap is mostly unnecessary. Align the pre-drilled holes on the license plate with the screw holes at the car's license plate installation position, then screw in the first set of screws. Be careful not to tighten them fully; just secure the license plate in place. Complete the installation of the remaining sets of screws. Once all four screws (some cars may only require two screws) are installed and verified to be secure, use a screwdriver to tighten them. The anti-theft cap has a small opening; slightly enlarge the opening with the screwdriver and then snap the anti-theft cap into place to complete the installation.

14

5

Share

What does streaming media mean for dash cams?

Streaming media for dash cams refers to a technology where cameras installed on the vehicle transmit real-time, lossless, and delay-free footage to the rearview mirror display, recording and broadcasting simultaneously. This provides an ultra-wide field of view, effectively eliminating blind spots and offering better safety for drivers. Functions of streaming media dash cams: These devices replace traditional optical rearview mirrors, allowing drivers to see a wider and clearer view of the rear. The viewing angle of a streaming media dash cam can reach 80-140 degrees, compared to just 18-20 degrees for traditional optical rearview mirrors. Advantages of streaming media rearview mirrors: Ultra-wide field of view: Traditional dash cams have a very limited field of view, barely meeting basic driving needs, and further widening the view is difficult. In contrast, streaming media rearview mirrors typically offer a five-fold wider field of view, comprehensively covering all lanes behind the vehicle. Ultra-clear and distortion-free: Clarity is the top priority when purchasing a dash cam. If the footage isn't clear enough to even read license plates, it can't be considered a proper dash cam. Streaming media rearview mirrors provide exceptionally clear footage with high color accuracy and no distortion. Superior anti-glare: While driving, especially at night, glaring headlights can be uncomfortable and increase hazards by obscuring the rear view. True streaming media rearview mirrors have excellent light absorption, preventing glare. Rain and fog resistance: They maintain clear rear visibility even in rainy or foggy conditions, unaffected by weather. In such conditions, water droplets on traditional mirrors severely obstruct the view. Streaming media rearview mirrors solve this issue, as their lenses are specially treated to repel water and maintain clear visibility in adverse weather.

9

5

Share

Is the throttle necessary for the second subject of the driving test?

The throttle is not necessary for the subject test. The second subject test is a field test, and you can drive in first gear without using the throttle. Precautions for Subject Two: Control speed when reversing into the garage: Do not go too slow or stop. Find your reference point and reverse slowly to avoid pressing the line when turning the steering wheel too quickly. Mock test: The purpose of the mock test is to familiarize candidates with the test environment and allow the instructor to point out areas where points are easily deducted. Therefore, mock tests are essential, and the best approach is to prepare well. Ensure preparation: When you get into the test car, remember to adjust the seat and rearview mirror to the state you find most comfortable and convenient. Keep in mind that unfamiliar rearview mirrors and seats directly affect judgment during the test.

3

4

Share

What are the factors that affect a car's fuel consumption?

Factors that affect a car's fuel consumption include: 1. Issues with spark plugs and high-voltage wires. As the vehicle's usage time extends, abnormalities in the ignition circuit may occur, leading to increased fuel consumption; 2. The degree of tire wear also impacts fuel consumption. Severe tire wear can cause slippage, requiring the engine to output more power, thereby increasing fuel consumption; 3. Some drivers open windows at high speeds to save on air conditioning, but this increases aerodynamic drag, leading to higher fuel consumption. It is recommended to use the car's air conditioning system flexibly.

14

4

Share

How many seconds should the fourth gear be maintained in Subject 3?

In Subject 3, it is best to maintain the 4th gear for more than 3 seconds. After starting in 1st gear, pay attention to shifting to 2nd gear more than 20 meters before the gear shifting project. Stabilize the speed of 2nd gear to 22 km/h. When you hear the gear shifting voice, first step on the accelerator to increase the speed of 2nd gear to 25 km/h, then step on the clutch to shift to 3rd gear, release the clutch, and step on the accelerator to increase the speed of 3rd gear to 30-35 km/h, then shift to 4th gear, and then downshift to 3rd gear. After that, downshifting does not require acceleration. Exam content: The exam content of Subject 3 includes preparation for getting on the car, light simulation test, starting, driving straight, gear shifting operation, changing lanes, parking by the roadside, going straight through intersections, turning left at intersections, turning right at intersections, passing pedestrian crossings, passing school areas, passing bus stops, meeting cars, overtaking, making U-turns, and driving at night. Notes: Lights: When changing lanes, making U-turns, turning, etc., pay attention to turning on the turn signal. After turning on the turn signal, it is best to hold it to prevent it from automatically turning off when the steering wheel is straightened, which may not be detected by the sensor. Driving straight: Generally, the training cars have been used for a long time. When driving straight, most of them will deviate. At this time, slightly turn the steering wheel to correct the direction, but the steering wheel should not be turned too much, otherwise it will affect the test results. In addition, when driving straight, look far ahead and find a reference point, so it is not easy to deviate. Speed: Except for driving straight or accelerating, it is best to control the speed of other test items at 20-30 km/h, which is easier to control.

1

4

Share

What is the reason for the HOWO truck not shutting off after turning the key?

What to Do When the Car Door Handle Freezes?

What is the correct method for installing license plate screws?

What does streaming media mean for dash cams?

Is the throttle necessary for the second subject of the driving test?

What are the factors that affect a car's fuel consumption?

How many seconds should the fourth gear be maintained in Subject 3?

What to Do When Your Driver's License Reaches 6 Years?

What is the fuel consumption per 100 kilometers for the Cadillac CT5?

What does EPC mean in a vehicle?

What does 101W on a tire mean?