What is the reason for the flashing engine warning light on a Chery QQ?

1 Answers
HenryLee
07/30/25 4:05am
The reason for the flashing engine warning light on a Chery QQ may be due to a malfunction in the engine ignition system, which causes poor ignition in one of the cylinders. Solution: It is necessary to use an automotive diagnostic tool to inspect the engine. After troubleshooting, clear the fault code. If there are no fault codes in the engine system but the engine warning light is still on, Solution: Wait until the engine temperature reaches above 80 degrees. While idling, press the accelerator pedal all the way down, allowing the engine speed to rise to around 4,000 RPM, then release the pedal. Repeat this operation three times, and the warning light will turn off by itself.
Was this review help?
7
4
Share
More Forum Discussions

Why can't the Jianghuai Refine accelerate normally while driving?

Jianghuai Refine cannot accelerate normally while driving due to the following reasons: 1. Excessive carbon deposits: Carbon deposits can cause local overheating, leading to premature ignition of the combustible mixture by the carbon deposits before the spark plug fires, known as knocking. This disrupts the normal operation of the engine, causing vibrations and resulting in the inability to gain power when stepping on the accelerator. 2. Damage to the fuel pump in the fuel tank: The fuel pump's working motor makes noise. If the fuel pump cannot supply fuel properly, it will lead to insufficient vehicle power. Check the fuel tank for leaks or blockages. If there is a severe leak, starting the vehicle could cause it to ignite due to static electricity.
13
5
Share

What Causes a Car to Fail to Shift Gears After Wading Through Water?

When the clutch gets wet, it may stick, resulting in incomplete disengagement, which necessitates replacing the clutch disc and pressure plate. Here are relevant details: 1. Definition: Located inside the flywheel housing between the engine and transmission, the clutch assembly is secured to the rear plane of the flywheel with screws. It functions as a switch-like device that transmits the engine power of a car or other power machinery to the axle. 2. Function: The driver can press or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine with the transmission, thereby cutting off or transferring the engine's power input to the transmission.
17
4
Share

How Much Refrigerant Should Be Added to a Car?

The addition and replacement of refrigerant do not have a fixed time cycle in principle. Whether it needs to be replaced or added mainly depends on the state of the air conditioning cooling. Overview of Refrigerant: Automobile refrigerant, also known as car coolant and commonly referred to as Freon, is divided into environmentally friendly R134a and non-environmentally friendly R12. Since R12 severely damages the atmospheric ozone layer and produces a greenhouse effect, it endangers the environment on which humans rely for survival. Solutions: When there is an excess of automobile refrigerant, it can be directly released into the atmosphere through the high-pressure pipe valve of the air conditioning system. However, if it is R12 refrigerant, direct release is not only environmentally unfriendly but also poses certain dangers, so this method is not recommended.
6
2
Share

Is a paint thickness gauge reading over 400 microns serious for bodywork?

Bodywork is severely affected, as the normal car paint thickness ranges between 120 to 180 microns. Overview of car paint: Automotive paint (English name: Car-paint) has undergone three major leaps in history: alkyd (enamel) paint in the 1920s; acrylic (enamel) paint in the 1960s, and clear coat (urethane) in the 1980s. Function of car paint: Automotive paint is a protective film sprayed onto cars, a type of coating that makes the car body less susceptible to corrosion and enhances its aesthetic appeal. Different automotive paints produce different effects, and the quality of the paint itself, along with the technology and a good painting environment, is crucial.
9
2
Share

What causes the tire pressure warning light to malfunction in a Jaguar F-PACE?

Reasons for the tire pressure warning light malfunction in a Jaguar F-PACE: Excessive deviation or underinflation in the front four tires indicates an issue with the vehicle's tire pressure. If the tire pressure system alerts, first pull over to the roadside and check the tire pressure of all four tires. There are three common methods of tire pressure monitoring: Direct Tire Pressure Monitoring: Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire pressure. Wireless transmitters send the pressure information from inside the tire to a central receiver module, which then displays the data for each tire's pressure. The system automatically alerts when the tire pressure is too low or if there is a leak. Indirect Tire Pressure Monitoring: When the pressure in a tire decreases, the vehicle's weight causes the rolling radius of that wheel to become smaller, leading to a faster rotation speed compared to the other wheels. By comparing the differences in rotation speeds between the tires, the system monitors tire pressure. Indirect tire pressure warning systems essentially rely on calculating the rolling radius of the tires to monitor pressure. Introduction to Tire Pressure Monitoring Systems (TPMS): TPMS combines the advantages of both systems mentioned above. It equips direct sensors in two diagonally opposite tires and includes a four-wheel indirect system. Compared to a fully direct system, this hybrid system reduces costs and overcomes the indirect system's inability to detect simultaneous underinflation in multiple tires. However, it still cannot provide real-time data on the actual pressure in all four tires as a direct system does.
2
0
Share

What Causes Ford Engine Failure?

Ford engine failure can be attributed to the following reasons: 1. Unqualified exhaust emissions: Issues such as poor fuel quality, malfunctioning catalytic converter, excessive carbon buildup in the intake pipe, clogged fuel injectors, faulty oxygen sensors, or occasional engine misfires can trigger the engine warning light. Among these, poor fuel quality causing the engine warning light to illuminate is the most common. 2. Poor engine system performance leading to warning light activation: Problems like faulty throttle pedal sensors, throttle position sensors, air flow meters, crankshaft position sensors, or poor circuit connections can all cause the engine warning light to come on. 3. Transmission system failure: In some vehicles, transmission system issues such as internal faults, slipping, or overheating are also indicated through the engine warning light.
12
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.