What is the reason for the BYD F3 to automatically lock the doors during inspection?

Where to Position the Jack When Changing Tires?

When changing tires, the jack should be positioned under the chassis near the wheel, on the raised area. The jack should be operated steadily and rhythmically when lifting, and lowered slowly. If multiple jacks are used simultaneously, they should be operated in sync. After using the jack, conduct a thorough inspection to check the hydraulic pressure and potential hazards, perform maintenance, and store it in an appropriate place. Here are some precautions when using a jack: 1. Temperature Considerations: The standard working fluid for most jacks is YB-N32 hydraulic oil. If the ambient temperature is below 10°C, switch to YB-N22 hydraulic oil; if it exceeds 40°C, use YB-N46 hydraulic oil. The normal operating temperature range for the jack pump is 10–50°C. If the oil temperature is too high, implement cooling measures or stop the pump. If the oil temperature is too low, use heating measures or operate at low pressure to raise the temperature. 2. Regular Inspections: High-pressure hoses are pressure-tested at 1.25 times the rated pressure before leaving the factory. Due to aging of the rubber material, users should perform regular inspections every six months during prolonged use. If leaks, bulges, or bursts occur during pressure testing, the hose must be replaced. Avoid kinking or sharp bends when using the hose, and keep a safe distance to prevent injury from bursting. 3. Annual Pump Maintenance: Clean all parts with kerosene during annual maintenance. Protect the mating surfaces of the jack from damage. After reassembly, ensure all moving parts operate smoothly without obstruction.

16

1

Share

Why is the MG5's fuel consumption so high?

MG5 average fuel consumption: 5.6~9.8L/100km, MIIT comprehensive fuel consumption: 5.6~7.8L/100km. The reasons for high fuel consumption are as follows: Abnormal tire pressure: Incorrect tire pressure can also affect the car's fuel consumption. When the tire pressure is too low or the tread is severely worn, the contact area between the tire and the road surface increases, friction increases, rolling resistance increases, and fuel consumption naturally rises. Excessive load: Long-term transportation of heavy loads increases the vehicle's weight, leading to greater driving pressure and higher fuel consumption. Car sensor failure: This is also a major cause of increased fuel consumption. When the water temperature sensor fails, it makes the engine mistakenly think the car is in a cold state, continuously sending signals to inject fuel, resulting in higher fuel consumption.

4

Share

When Did Henan Province Implement the China VI Emission Standard?

The Department of Ecology and Environment of Henan Province issued the "Announcement No. 5 [2019] of the Department of Ecology and Environment of Henan Province on the Implementation of the National Phase VI Vehicle Emission Standards," declaring that the "China VI Emission Standard for Motor Vehicles" would be officially implemented in Henan Province starting from July 1, 2019. According to the announcement, the "China VI Standard" in Henan Province is implemented in phases: 1. Phase One: Starting from July 1, 2019, light-duty vehicles sold and registered within the administrative region of Henan Province must comply with the "Limits and Measurement Methods for Emissions from Light-Duty Vehicles (China VI)" (GB18352.6-2016) Phase 6a or 6b standards. Gas-powered vehicles produced, imported, sold, and registered in Henan Province must meet the "Limits and Measurement Methods for Emissions from Heavy-Duty Diesel Vehicles (China VI)" (GB17691-2018) Phase 6a or 6b standards. Urban-use diesel vehicles sold and registered in Henan Province must comply with the "Limits and Measurement Methods for Emissions from Heavy-Duty Diesel Vehicles (China VI)" (GB17691-2018) Phase 6a standards. 2. Phase Two: Starting from July 1, 2020, all urban-use heavy-duty diesel vehicles produced or imported within the administrative region of Henan Province must comply with the "Limits and Measurement Methods for Emissions from Heavy-Duty Diesel Vehicles (China VI)" (GB17691-2018) Phase 6a standards. 3. Phase Three: Starting from July 1, 2021, all heavy-duty diesel vehicles produced, imported, sold, and registered within the administrative region of Henan Province must comply with the "Limits and Measurement Methods for Emissions from Heavy-Duty Diesel Vehicles (China VI)" (GB17691-2018) Phase 6a standards.

11

3

Share

Can a motorcycle battery be charged directly on the vehicle?

1. Yes, it can be charged on the vehicle, but ensure the vent holes are unobstructed. Most importantly, avoid overcharging. The charging duration should be determined based on your charger's power and the battery's discharge level. 2. Pay special attention to connecting the positive and negative terminals correctly and ensuring the vent tube near the battery is not blocked. Motorcycle batteries typically have a small capacity, around 5AH-9AH, and are 12V batteries. Therefore, set the charger to around 12V1A. For a 7AH battery, it takes approximately 7 hours to fully charge. 3. Do not start the motorcycle or turn on high beams during charging, as this can damage the charger. Before charging, clear the vent holes on the battery's filler caps to ensure they are not blocked. This allows proper ventilation even when the battery generates a lot of bubbles during charging. Additionally, ensure the live wire (the red one) connected from the battery does not come into contact with the vehicle to prevent short circuits.

14

3

Share

What is the 0-100km/h acceleration time for the CHR Hybrid?

First, set the Toyota CHR to sport mode. With a full-throttle start, there will be slight wheel spin on the front wheels, but this does not affect the car's response. The body reacts promptly, and the initial acceleration feels strong. The final 0-100km/h test result is 9.32 seconds. As a compact SUV, the Toyota CHR's fuel consumption should not be very high. According to the combined fuel consumption data released by the Ministry of Industry and Information Technology, the CHR's fuel consumption is 5.7L/100km. Of course, this figure is not the actual fuel consumption. Based on independent tests by owners, the actual fuel consumption of the Toyota CHR is around 6.8L/100km. This model performs well in terms of power. First, the fuel consumption is relatively low, and the 0-100km/h performance is quite good.

16

2

Share

How to Distinguish Between a 6-Volt and 12-Volt Motorcycle Battery?

Motorcycle batteries come in two types: 6-volt and 12-volt. However, 6-volt batteries were used in older models without electric starters and are now obsolete. So, how can you tell if a motorcycle battery is 6-volt or 12-volt? Here are some methods: 1. Use a multimeter to directly measure the voltage. 2. Each battery cell is 2 volts. If the battery has a transparent casing, you can count the number of cells: 3 cells indicate 6 volts. For opaque casings, remove the top cover and count the number of holes. For example, a battery with 6 holes is 12 volts. 3. If you can find the model or specifications on the casing, you can look up the voltage value online. Some batteries even have the voltage value printed directly on them.

3

2

Share

What is the reason for the BYD F3 to automatically lock the doors during inspection?

Where to Position the Jack When Changing Tires?

Why is the MG5's fuel consumption so high?

When Did Henan Province Implement the China VI Emission Standard?

Can a motorcycle battery be charged directly on the vehicle?

What is the 0-100km/h acceleration time for the CHR Hybrid?

How to Distinguish Between a 6-Volt and 12-Volt Motorcycle Battery?

Are the XRV and CRV in the same vehicle class?

What Causes the Engine Cooling Fan to Stop Working?

How many seconds does the CB400F take to accelerate from 0 to 100 km/h?

How Does Isuzu Solve DPF Regeneration?