What is the reason for the blower not working in the Tiida?

3 Answers
MacCora
08/30/25 7:00am
The reasons for the air conditioning blower not working in the Tiida can vary, but it is usually due to motor failure or poor circuit connections. Possible causes include blower motor failure, blower motor control module failure, faulty blower switch, or related wiring and connectors experiencing open circuits, short circuits, or poor contact. Additional information about the blower is as follows: 1. Function: The car blower's function is to direct the cold air from the air conditioning evaporator or the hot air from the heater core into the vehicle. If the car's air conditioning blower stops working, it will affect the use of the car's air conditioning system. 2. Symptoms: The symptom of a non-working blower is that when the air conditioning cooling switch is turned on, the compressor may operate, but the blower does not run when the blower switch is activated.
Was this review help?
1
4
Share
DelCaden
09/12/25 4:01am
As a seasoned driver who has owned a Nissan Tiida for many years, I've encountered several instances of blower failure. The most common cause is a blown fuse. Check the fuse box in the cockpit for the one labeled "Blower" or "FAN" and inspect if it's melted. If that's not the issue, the blower motor itself might have aged - after years of use, bearings can seize or the motor may burn out, preventing it from turning. Loose wiring connections are also frequent culprits, especially when connectors corrode after prolonged vibration. Once I even experienced a faulty blower resistor that only allowed low-speed operation. Being without heating in winter is miserable, so prompt action is needed. I recommend first checking the fuse as a simple diagnostic step. If that doesn't solve it, visit a repair shop where they can test circuits and replace components to ensure proper AC operation and driving safety.
Was this review help?
20
2
Share
Expand All
MacEmilia
10/26/25 4:49am
My own Tiida's blower also occasionally stops working, which is quite annoying. Usually, start with the fan switch and try adjusting the speed to see if it responds; if there's no reaction, it might be a blown fuse. Check the engine compartment or the footwell fuse box for the one related to the air conditioning and replace it. Or the relay might be stuck, preventing the fan from starting. It could also be an issue with the resistor module, causing the airflow control to malfunction. It's especially unbearable during hot summers. I've tried opening it up myself to check for loose connectors, and sometimes a simple fix is enough. For the long term, regularly clean out dust to prevent blockages. If you can't solve it, don't push through—getting it repaired by a professional is the right way to go. Safety first.
Was this review help?
20
3
Share
Expand All
More Forum Discussions

How to replace the battery in a Golf 7 key?

Golf 7 refers to the Volkswagen Golf 7. The steps to replace the battery in a Golf 7 key are as follows: 1. Confirm the battery model, which is CR2025 for the Golf 7. 2. Prepare the necessary tools, such as nail clippers, a coin, or a paperclip. 3. Insert the nail clippers into the side (in the key slot) and pry it open. 4. Once opened, you will see the battery. Use the paperclip to gently pry it out. 5. Replace it with a new battery and close the key cover. Be careful not to reverse the positive and negative poles when replacing the battery.
9
1
Share

What are the methods to repair a leaking fuel tank?

Methods to repair a leaking fuel tank are: 1. Apply soap or chewing gum to the leaking area; 2. Weld the hole with tin solder or use AB glue to fill it; 3. Use epoxy resin adhesive; 4. Drain the fuel from the tank, clean it with soapy water, and then repair it by welding. Methods to address engine oil leaks are: 1. Inspect or replace the engine oil filter; 2. Replace the valve cover gasket; 3. Remove the engine timing cover and apply sealant; 4. Tighten or replace the oil drain plug; 5. Replace the oil pan gasket and apply sealant; 6. Replace the crankshaft oil seal. Engine maintenance methods include: 1. Use qualified engine oil; 2. Use qualified coolant and antifreeze; 3. Regularly clean the radiator scale; 4. Regularly remove engine carbon deposits.
4
2
Share

How to Use the Car Odometer AB?

Car odometer AB is used as follows: when starting from point A, reset one of the trip data to zero and start the car. Upon arriving at point B, check the data on the trip to know the distance between the two points. The working principle of the odometer is based on the known diameter of the car's wheels. By calculating the circumference of the wheel, the number of rotations required for the wheel to cover one mile is determined. The odometer automatically records the number of wheel rotations and divides it by the number of rotations corresponding to one mile to obtain the distance traveled. The method to adjust the odometer is: 1. Unplug the odometer sensor connector of the drive shaft under the car's hood; 2. Insert the output plug of the mileage adjuster into the signal socket of the sensor; 3. Plug the mileage adjuster into the cigarette lighter; 4. Turn the car key to start the dashboard and adjust the adjustment button on the mileage adjuster; 5. Adjust the speed as needed.
1
0
Share

Solutions for Engine Vibration After Fuel Injector Cleaning

The reason for engine vibration after fuel injector cleaning is: It's quite normal to experience vibration after cleaning fuel injectors. The vehicle's ECU has a self-learning function that stores pre-cleaning fuel injection data. When injector nozzles are clogged with carbon deposits, the throttle valve automatically increases its opening to maintain idle air intake. After cleaning, the throttle valve still uses the clogged data, causing unstable idle and severe vibration due to excessive throttle opening. Simply resetting the throttle valve to factory settings can resolve this issue. The working principle of fuel injectors is: High-pressure fuel is pumped into the injector's supply port, creating pressure inside that acts on the injector's conical surface. When oil pressure exceeds the set value, the injector valve opens, spraying atomized fuel through small nozzles into the engine cylinder for combustion, driving piston reciprocation.
13
1
Share

How to Use the Internal and External Air Circulation in a Car?

Here are the methods for using the internal and external air circulation in a car's air conditioning system: 1. On the control panel of the car's air conditioning, there is a button to switch between internal and external circulation. You can toggle it using this button. 2. When driving in congested urban areas, it is recommended to use the internal circulation mode. For long-distance trips or highway driving, the external circulation mode is advisable. Recommendations for using internal and external air circulation in cars: 1. The car's air conditioning system is equipped with an air filter, which is designed to filter out dust and particulate matter from the air. 2. The air filter needs to be replaced regularly. Failure to replace it for an extended period can result in unpleasant odors in the car's air conditioning and can be harmful to the health of passengers. 3. When replacing the air filter, it is important to choose products from reputable brands.
11
5
Share

What is the difference between Jaguar and Leopard car logos?

The difference between Jaguar and Leopard car logos lies in their appearance: the Jaguar logo features a leaping lion, while the Leopard logo consists of a circle with a triangle inside. Taking the 2020 Jaguar XEL as an example, it belongs to the mid-size car category with body dimensions of 4778mm in length, 1850mm in width, and 1429mm in height, a wheelbase of 2935mm, a fuel tank capacity of 62 liters, and a curb weight of 1730kg. The 2020 Jaguar XEL is equipped with a double-wishbone independent front suspension and a multi-link independent rear suspension. It is powered by a 2.0L turbocharged engine delivering a maximum horsepower of 200PS, a maximum power of 147kW, and a maximum torque of 320Nm, paired with an 8-speed automatic transmission.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.