What is the reason for the automatic locking of JAC Tongyue?

Will the engine automatically shut down when overheating?

Will the engine automatically shut down when overheating? Reasons for shutdown: Modern vehicles are equipped with engine protection devices. When the engine coolant temperature becomes excessively high, an alarm will be triggered, and the vehicle will automatically shut down to protect the engine. The vehicle can be driven again after the engine cools down. Using water as a substitute for coolant: In emergency situations where coolant is unavailable, water can be used as a temporary substitute. However, the coolant must be replaced immediately after reaching the destination and resolving the issue. Prolonged use of water may lead to reduced cooling system efficiency, increased fuel consumption, and decreased engine power.

7

3

Share

Can You Make a U-Turn at a Circular Traffic Light?

Circular red lights do not permit U-turns. Reasons prohibiting U-turns at circular red lights: At intersections without prohibited U-turn signs, drivers may execute U-turns during green light phases, provided they do not impede the normal flow of other vehicles or pedestrians. According to Article 49 of the Implementation Regulations of the Road Traffic Safety Law of the People's Republic of China, motor vehicles are prohibited from making U-turns at locations with no U-turn or no left turn signs/markings, as well as at railway crossings, crosswalks, bridges, sharp curves, steep slopes, tunnels, or other potentially hazardous road sections. Permissible U-turn conditions: Motor vehicles may make U-turns at locations without prohibited U-turn or no left turn signs/markings, but must not obstruct other properly moving vehicles or pedestrians. At intersections without dedicated non-motor vehicle or pedestrian traffic signals, cyclists and pedestrians should follow the indications of motor vehicle traffic signals.

12

5

Share

Is Waxing Necessary with a Paint Protection Film?

Waxing can be optional. Functions of Waxing: Waxing is intended to protect against corrosion from acid rain, dust, and other corrosive substances. A paint protection film is not indestructible; prolonged exposure to contaminants like acid rain can accelerate its deterioration. Without regular maintenance of the paint protection film and frequent cleaning of the vehicle, the film will gradually age, lose its luster, and diminish its optimal aesthetic appeal. Functions of Paint Protection Film: Waxing is not absolutely essential for a paint protection film because high-quality films inherently possess strong anti-corrosion properties and are designed to protect the car's paint. However, nothing in the world is completely immune to corrosion, and paint protection films are no exception. Acid rain, dust, bird droppings, and other contaminants can still erode the film and affect the vehicle's surface shine, so the paint protection film also requires protection.

9

4

Share

What Does the Engine Displacement Number Represent?

The size of a car's engine displacement represents the power of the vehicle. Introduction to Engine Displacement: Displacement refers to the volume of exhaust gas emitted by the engine during one complete working cycle. Generally, a larger displacement means stronger power but also higher fuel consumption. The size of a car's engine displacement can serve as an indicator of the vehicle's class. Total engine displacement is the sum of the working volumes of all the engine's cylinders, measured in liters. Explanation of Engine Displacement Sizes: In China, car classification is based on the total engine displacement. Vehicles with a displacement of 1 liter or less are classified as micro cars. Those with a displacement greater than 1 liter but less than or equal to 1.6 liters are considered standard-class cars. Cars with a displacement greater than 1.6 liters but less than or equal to 2.5 liters fall into the mid-class category. Vehicles with a displacement greater than 2.5 liters but less than or equal to 4 liters are classified as upper mid-class cars.

3

1

Share

What Causes Engine Idle Vibration After Hard Braking?

High-speed driving followed by braking to decelerate causing engine vibration is a normal phenomenon. Introduction to Idle: When an engine runs without load, it is called idling. During engine operation, if the accelerator pedal is completely released, the engine enters idle state. The rotational speed during engine idling is called idle speed. Idle speed can be adjusted by modifying parameters such as throttle opening. Generally, the optimal idle speed is the minimum RPM at which the engine does not vibrate. Function of Idling: Avoiding wasted work - Idling overcomes the engine's internal friction to maintain minimum rotational speed, providing convenience for drivers during various driving conditions and temporary stops. For instance, when waiting at traffic lights or in congested traffic, although the duration may be brief, temporarily turning off the engine can achieve immediate energy-saving and emission-reduction effects.

5

2

Share

Why is there abnormal noise when turning the steering wheel?

The reasons for abnormal noise when turning the steering wheel may include: sound from the turn signal rebound clip, noise from the steering column dust cover, or interference noise from the clock spring. Noise from the steering column dust cover: If the noise comes from below the steering wheel while driving or turning the wheel stationary, it is likely due to the steering column dust cover. This friction noise is caused by lack of lubrication and can be resolved by applying some grease. Interference noise from the clock spring: If the noise comes from inside the steering wheel when turning, the issue may be with the clock spring interference. Try removing the steering wheel and applying grease to the clock spring. If the noise persists, the clock spring may need replacement. Noise from the shock absorber thrust bearing: If the noise comes from outside the vehicle when turning the steering wheel, it might be due to insufficient lubrication in the shock absorber thrust bearing. Open the hood to check if the noise originates from the thrust bearing. If so, applying grease may solve the issue. If the noise continues, the thrust bearing may need replacement.

20

5

Share

What is the reason for the automatic locking of JAC Tongyue?

Will the engine automatically shut down when overheating?

Can You Make a U-Turn at a Circular Traffic Light?

Is Waxing Necessary with a Paint Protection Film?

What Does the Engine Displacement Number Represent?

What Causes Engine Idle Vibration After Hard Braking?

Why is there abnormal noise when turning the steering wheel?

Does changing the steering wheel affect the car?

How Many Spark Plugs Does a Four-Cylinder Motorcycle Have?

What is the diameter of a motorcycle handlebar?

Is it harmful to shift gears while coasting downhill in neutral on a motorcycle?