···
Log in / Register

What is the reason for the abnormal noise in the Fabia engine compartment pulley?

1 Answers
OliveDella
09/01/25 6:09am

The abnormal noise in the Fabia engine compartment pulley may be caused by belt aging. Reasons for the abnormal noise: The abnormal noise is usually caused by the aging of various belt groups in the engine and the smooth wear of the contact surface between the belt and the pulley. It often occurs when the engine speed changes rapidly, and sometimes the increased load on the accessories driven by the belt can also cause the belt to make noise. Solution: First, it is necessary to check whether the bearings of the accessories driven by the belt are damaged, stuck, loose, or if the accessory power has increased. If this is the case, the parts need to be replaced. In addition, the belt can be directly replaced. The belt can be replaced by yourself or at a 4S shop for repair.

Was this review help?
2
3
Share
More Forum Discussions

How to adjust the dashboard brightness of Mercedes-Benz V260?

After entering the menu page, press the up and down buttons to select the lighting submenu; press OK to confirm after selecting the submenu. After confirmation, press the up and down buttons again to select the brightness display switch function, and you will see the relevant settings. After entering the relevant settings, press OK again to confirm. After confirmation, press the up and down buttons to select an appropriate brightness level between Brightness 1 and Brightness 5. After selecting the appropriate brightness, press OK to save the settings.
16
4
Share

What are the reasons for the sudden silence of the entire audio system in the Haval H6?

Here are the reasons why the entire audio system in the Haval H6 suddenly stops working: 1. System lag: If the car audio has no sound but otherwise functions normally, it is usually not a mechanical failure but rather due to system lag. In this case, try restarting the car to restore the system. After the system recovers, the audio should generally resume working. 2. Bluetooth connection failure: If the car audio is connected via Bluetooth from a mobile phone, try disconnecting and reconnecting the Bluetooth. An incoming call can interrupt the signal input, and after the call ends, Bluetooth lag or failure may cause the audio to have no sound. Users who have used Bluetooth headphones have likely encountered this issue. Simply reconnect to resolve it. 3. Wiring issues: If none of the above problems occur, check if the CD power supply is faulty. If the power indicator is lit and the CD can be turned off normally, then the issue is not with the power supply. If everything seems fine, inspect whether the power cables have aged or if the fuse has come loose. Otherwise, it is best to take the car to a repair shop for further inspection and maintenance.
14
1
Share

How to Clean a Dirty Mercedes Radar Sensor?

When the driver sees this warning, simply wipe all the probes with a tissue or towel. It could be mud, water, or plastic stuck to the probe, and cleaning it will solve the issue. The vehicle's radar sensors should be cleaned promptly. Dirt on the probe can cause detection abnormalities or even incorrect signal readings, which may affect the driver's judgment and lead to accidents. If the measurement involves a multi-dimensional vector, the sensor's cross-sensitivity should be as minimal as possible.
10
1
Share

How to Install Motorcycle Sequential Turn Signals?

First, locate a suitable place to fix the turn signals. If there isn't one, you'll need to drill holes yourself. After drilling and fixing, thread the wires through the drilled holes. Connect yellow to yellow, pink to pink, green to green-white. The red wire connects to the battery's positive line, and the black wire is the voltage regulator line. After connecting, use a multimeter to measure the voltage by testing the battery's positive and negative terminals. Use a 12V 20A0 battery to replace the original motorcycle battery. This can extend the battery's working time and prolong the usage of the motorcycle's electrical equipment, lighting, and electric start system.
12
1
Share

How to Change BMW Key Language from English to Chinese?

Adjust through the car's multifunction steering wheel. First, locate the multifunction steering wheel, the key with an LCD display, and various auxiliary functions. Click the SET button on the left side of the steering wheel. Press the OK button on the multifunction steering wheel for five seconds. The language settings option will appear on the display screen. Select the Mandarin Chinese option, and you will notice the display no longer shows English. The vehicle information display function allows you to check the vehicle's status, doors, remaining fuel mileage, and unauthorized door opening alerts on the key's display screen at any time.
14
4
Share

What are the steps for disassembling and assembling a Jetta engine?

Remove the fuel pump fuse, start the engine to release fuel pressure, and disconnect the negative battery cable. Disassemble the intake pipe assembly, remove the upper intake manifold assembly, and take off the lower intake manifold assembly to prevent debris from entering the passages. Remove the heated oxygen sensor, detach the exhaust pipe and gasket from the mounting bracket, and clean the exhaust manifold sealing surface to check for holes, damage, or cracks. Remove the protective plate to expose the generator belt, take off the belt, remove the engine crankshaft output pulley, and detach the triangular fixed bracket on the engine side. Loosen the cylinder head cover bolts in a diagonal sequence, remove the cylinder head cover, take off the valve cover gasket (ensuring its integrity), and then remove the cylinder head.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.