What is the real fuel consumption of the Mistra 1.8L?

1 Answers
Christopher
07/29/25 11:28pm
The real fuel consumption of the Mistra 1.8L is 9.9L/100km for manual transmission models and 7.8-10.3L/100km for automatic transmission models. Below are specific methods to reduce fuel consumption: 1. Lightly press the accelerator: When the car starts at low speed, it is the peak fuel consumption period. Therefore, lightly pressing the accelerator during startup to prevent excessively high RPM can effectively reduce fuel consumption. 2. Avoid high RPM: Avoid unnecessary high RPM as much as possible, as fluctuating engine RPM can also significantly consume fuel. 3. Regular maintenance: Change the engine oil and remove carbon deposits. 4. Avoid emergency braking: Anticipating road conditions in advance not only improves driving safety but also saves fuel. For example, gradually slowing down before traffic lights and utilizing inertia to glide.
Was this review help?
14
2
Share
More Forum Discussions

What Are the Symptoms of Damaged Car Springs?

Here are the obvious symptoms of damaged car springs: 1. When the car is driving on the road and encounters bumpy sections, it will make various "clunking" or "creaking" sounds. 2. When the car is driving on the road, the body will feel a strong sense of swaying. 3. When the car is moving slowly and suddenly performs an emergency brake, the body will feel a strong vibration. Here is extended information on how to replace rear car springs: 1. Lift the vehicle and disconnect the parts connecting the shock absorber under the chassis. 2. Lower the vehicle, with one person below holding the shock absorber and another above removing the top screw of the shock absorber, then take out the shock absorber. 3. Tighten the spring, ensuring to pull symmetrically when tightening. 4. Use an air impact wrench to remove the central screw of the shock absorber. 5. Remove the spring.
13
2
Share

What lights should be turned on during foggy weather in the Subject 3 driving test?

During the Subject 3 driving test in foggy weather, it is necessary to turn on the fog lights and hazard warning flashers. The following is an introduction to the content of the Subject 3 test: 1. Vehicle preparation, starting, and straight-line driving. 2. Gear shifting operations, lane changing, and pulling over. 3. Going straight through intersections, turning left at intersections, and turning right at intersections. 4. Passing pedestrian crossings, school zones, and bus stops. 5. Meeting vehicles, overtaking, making U-turns, and nighttime driving. Below is extended information about the Subject 4 test content: 1. Requirements for safe and civilized driving operations. 2. Safe driving knowledge under adverse weather and complex road conditions. 3. Emergency handling methods for situations like tire blowouts. 4. Knowledge of post-traffic accident handling.
2
4
Share

Parking in First Gear or Neutral?

When parking, you can either engage first gear or neutral. Engaging first gear can prevent the vehicle from rolling. Below are specific instructions regarding parking gear selection: 1. On generally flat road surfaces, first gear should be engaged when parking. 2. When parking on an uphill slope, engage a forward gear; when parking on a downhill slope, engage reverse gear. Below are expanded notes on gear-shifting taboos: 1. Looking down at the gear lever while shifting. 2. Prolonged driving in low gear. Generally, higher gears are more fuel-efficient than lower gears. Therefore, upshift promptly after starting. 3. Failing to fully depress the clutch when shifting, which can damage gears. Additionally, when not using the clutch, avoid resting your foot on it to prevent excessive wear on the release bearing. 4. Veering off course while shifting gears. 5. Forcing the gear lever when unable to engage a gear smoothly. 6. Rocking the gear lever back and forth when in neutral. This can cause unnecessary wear on components and affect shift timing. 7. Skipping gears when upshifting. Upshifting should be done sequentially to maintain continuous power, while downshifting can skip gears. 8. Engaging reverse gear before the vehicle comes to a complete stop. This can easily damage gears.
4
5
Share

What Causes Car Door Squeaking?

Here are the reasons for car door squeaking: 1. Door hinges rusted or deformed due to prolonged use. After cleaning the grease on the surface of door hinges, limit arm rods, limit pin shafts, and connecting brackets, you can appropriately lubricate them with special lubricating oil. 2. Loose or deformed internal window regulators causing noise. 3. Unfixed or detached door trim panels causing squeaking. Below is extended information about the causes of car acceleration noise: 1. Excessive engine carbon buildup. 2. Poor gasoline filtration. 3. Poor gasoline quality. 4. Aging spark plugs. 5. Engine malfunction. 6. Cylinder failure. Below is extended information about solutions for car acceleration noise: 1. Replace engine oil. 2. Clean engine carbon deposits. 3. Replace spark plugs. 4. Conduct a comprehensive inspection and repair of the car.
13
0
Share

How to Break in an Automatic Transmission Car Now?

Here are the methods for breaking in an automatic transmission car: 1. Pay attention to the speed of the new car; avoid driving at a constant speed for extended periods. 2. Use the various gears of the transmission reasonably and drive different distances. 3. Ensure both low-speed and high-speed operating conditions are included. Below is extended information on precautions for driving an automatic transmission car: 1. Generally, unless specifically required, avoid frequently shifting the gear lever between D, 3, 2, 1, etc. 2. When starting an automatic transmission car, ensure the gear is in P or N to avoid damaging the transmission. 3. If the automatic transmission car fails to start, do not push it manually or tow it with another vehicle, as this may cause severe damage. 4. When reversing an automatic transmission car, ensure the vehicle is completely stopped before shifting into R gear.
12
0
Share

How to Clean Car Seat Belts?

Cleaning tips for seat belts: 1. For stains on car interior items, foam cleaner is practically a universal solution. Spray the cleaner onto the seat belt, wait for a dozen seconds, then gently scrub with a soft brush. After cleaning, wipe it dry with a clean towel. Note: Do not use the seat belt before it is completely dry. 2. If foam cleaner is not available, soapy water can also be used for cleaning. Avoid using highly corrosive cleaning products. Fully extend the seat belt and secure the top with a binder clip, then soak the belt in warm soapy water. After cleaning, dry it with a soft cloth. 3. Before the seat belt is completely dry, do not remove the binder clip at the top. Wait until it is fully dry before retracting it. If the seat belt fails to tighten promptly after cleaning, it is advisable to have it inspected at a professional repair shop.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.