What is the real fuel consumption of the 2011 Tiida?

Where is the handbrake of Volkswagen CC?

The handbrake of Volkswagen CC is located on the left side of the steering wheel, which is a button with the letter P. Here is the relevant introduction of Volkswagen CC: 1. In terms of appearance, the CC coupe has a sleek body with a fastback design, prominent lines, and a powerful rear wheel arch, giving a sense of readiness. The front face is sharp and full of presence, featuring classic frameless doors. The high and low beam headlights are integrated with the grille, and the daytime running lights are completely connected with the grille, with a layered design. Notably, the flowing turn signal design of the taillights is very eye-catching on the road. 2. In terms of handling, the steering is slightly better than the Magotan, being light yet precise. The chassis is well-tuned, allowing smooth lane changes and turns. Despite the high suspension, the body roll during cornering is well-controlled, and the tire grip is also good. For a sporty-oriented car, it offers a comfortable driving experience. 3. In terms of power, the Volkswagen CC is still equipped with three engines: 1.8TSI (160 horsepower), 2.0TSI (200 horsepower), and V6 3.0FSI (250 horsepower). The transmission system matches the 1.8TSI engine with a 7-speed DSG dual-clutch transmission, while the other models are equipped with a 6-speed DSG dual-clutch transmission.

13

2

Share

How to Bleed the Brake System After Adding Brake Fluid?

The steps for bleeding the brake system after adding brake fluid are as follows: 1. The bleeding operation requires two people to cooperate. After replacing or topping up the brake fluid, the air in the hydraulic lines should be bled. 2. One person sits in the driver's seat and repeatedly presses the brake pedal to raise its position, then holds the pedal steady without releasing it. Meanwhile, another person underneath the vehicle loosens the bleeder valve to allow air and brake fluid to escape from the lines. When the pedal position drops, immediately tighten the bleeder valve. 3. Repeat this process several times until no air bubbles are seen escaping from the plastic tube. Tighten the bleeder valve and reinstall the dust cap. Follow the above method to bleed the other wheel cylinders in sequence. During the bleeding process, continuously check and top up the brake fluid until all air is completely expelled. Then, add an adequate amount of the specified type of brake fluid to the reservoir.

19

1

Share

What does 'set' mean when it appears on a car?

The appearance of 'set' on a Volkswagen vehicle indicates a tire pressure alarm, and it is necessary to store the tire pressure. Its function is to adjust the tire pressure of all four tires to the standard level, then press and hold 'set' for three seconds while observing the speedometer dial, where a symbol of an exclamation mark inside brackets will appear. Upon hearing a 'ding' sound, the tire pressure of all four tires will be set according to the adjusted values. Precautions related to tire pressure are as follows: 1. Observe the tire condition before traveling. Radial tires—commonly known as low-pressure tires—are normal as long as the flatness is not too low; if you feel strong elasticity when pressing with your foot and they are not soft, they are fine. High-pressure tires—which are bias-ply tires with inner tubes—are normal if the shoulder area does not protrude when viewed from the front (commonly referred to as 'not bulging') and the contact area with the ground appears similar to usual when viewed from the side. 2. Pay attention to the sound of friction between the tires and the ground while driving, feel the cushioning force when passing over uneven roads, and notice if there are any changes in acceleration when pressing the gas pedal compared to usual. 3. Normally, check and replenish the tire pressure at a professional tire repair shop every week.

8

4

Share

What tire models does the Volkswagen Tharu have?

The Tharu comes with three tire models: 225/60R16, 225/55R17, and 225/50R18. Below is a related introduction to the Tharu: 1. Exterior: The design adopts the Rock-Cutting concept, featuring raised lines on the ridge-like hood for a stronger sense of power, wide-body dual U-shaped full LED headlights that tilt upwards, and grille strips extending to the headlights. 2. Interior: The cabin features a horizontal layout, enhanced with IMD material panels for a premium feel. Large decorative panels integrate the instrument cluster, display screen, and air vents into a unified design. 3. Powertrain: The Tharu is equipped with a 1.4T and two 2.0T turbocharged engines, delivering maximum power of 110kW and 137kW respectively, with peak torques of 175Nm, 250Nm, and 320Nm.

3

2

Share

Will the manufacturer provide warranty if the car is not maintained at a 4S shop?

Even if a car is not maintained at a 4S shop, the manufacturer will still provide warranty. The "Motor Vehicle Maintenance Management Regulations" clearly stipulate that manufacturers and 4S shops cannot refuse to provide warranty for vehicles on the grounds that maintenance was not performed at an officially authorized shop, meaning car owners are free to choose their maintenance location. Except for automobile manufacturers fulfilling their responsibilities for defective vehicle recalls and the "three guarantees" for vehicle quality, no unit or individual may force or covertly force the designation of a maintenance operator. Therefore, car owners can freely choose their maintenance location, while 4S shops must comply with providing warranty. However, it is important to note that if maintenance is performed elsewhere, it is essential to keep the maintenance invoice, repair records, and certificates for replaced parts as proof. That said, there are benefits to getting maintenance done at a 4S shop. 4S shops use manufacturer-specified oils and maintenance products and will guide customers on proper usage and fault feedback based on their vehicle usage, which is generally not as professional at external auto repair shops.

15

0

Share

Should Tire Pressure Be Higher or Lower in Hot Weather?

In hot weather, tire pressure tends to increase. You can adjust it to the lower limit of the standard tire pressure based on the vehicle's load. The standard tire pressure for sedans is usually indicated on the B-pillar near the front doors or on the fuel tank cover. Adjust it to around 2.1 to 2.3 bar. Standard Tire Pressure: For standard tires, the standard pressure is 240-250 kPa, while for reinforced tires, it is 280-290 kPa. Since most vehicle tires fall under the standard category as per international regulations, this is why 4S shops generally inflate tires to 2.5 bar (1 bar = 100 kPa). Summer Tire Precautions: Regularly check tire pressure and inflate according to standard values; inspect tire conditions periodically to avoid bulges, punctures, and excessive wear; do not cool extremely hot tires with cold water, as extreme temperature changes and shocks can accelerate tire aging and reduce lifespan—allow them to cool naturally.

11

4

Share

What is the real fuel consumption of the 2011 Tiida?

Where is the handbrake of Volkswagen CC?

How to Bleed the Brake System After Adding Brake Fluid?

What does 'set' mean when it appears on a car?

What tire models does the Volkswagen Tharu have?

Will the manufacturer provide warranty if the car is not maintained at a 4S shop?

Should Tire Pressure Be Higher or Lower in Hot Weather?

Where is the throttle body located?

What brand is the OPEN-COUNTRY tire?

Can car maintenance only be done at the 4S store where the car was purchased?

How to Reset the Engine Oil on the 10th Generation Accord?