What is the range of WM Motor electric vehicles in kilometers?

What Causes Poor Rebound in Motorcycle Suspension?

Poor rebound in motorcycle suspension is caused by a broken or overly soft suspension spring. Inverted Suspension: Inverted suspension provides greater support to the vehicle body, which is beneficial for extreme driving and cornering. In the event of a collision, due to its strong rigidity, the triple clamp or frame is more likely to deform, which is the opposite of conventional suspension. The spring is less likely to be damaged in a fall. The piston moves upward from below. Conventional Suspension: It is thinner at the top and thicker at the bottom, with the mechanical structure of the suspension located below. It has a relatively longer travel, a simple structure, and is less prone to oil leakage. In a frontal collision, the suspension usually deforms, while the triple clamp is less likely to be damaged. However, its performance in motion is average, and it has some impact on the rigidity of the vehicle body. The spring is more likely to be damaged in a fall. The piston moves downward from above. Motorcycle Suspension: The function of motorcycle suspension is to elastically connect the frame and the wheels, absorbing and mitigating the impact and vibrations from uneven road surfaces on the frame. If the suspension is too hard, the vehicle will vibrate severely, and the rider will constantly experience shocks. If it is too soft, the vibration frequency and amplitude will make the rider uncomfortable.

7

1

Share

Can OnStar start the engine without the key?

Yes. OnStar has a remote control function, which allows you to start the engine even without the key. Remote Start: After remotely starting the engine via OnStar, bring the key into the vehicle's sensing area, press the brake pedal, and press the start button. When the light turns green, you can drive away. OnStar is a comprehensive wireless service that utilizes wireless technology and GPS satellites, allowing users to connect with a customer service center with just one button and receive full voice assistance to resolve issues. Features of OnStar Remote Start: High reliability with significantly reduced failure rates; convenient usage, enabling remote engine start anytime and anywhere; full vehicle heating to minimize cold-start wear on the engine, effectively protecting the vehicle; easy installation.

14

4

Share

What Causes Heavy Steering Wheel When Turning in Place?

Heavy steering wheel when turning in place occurs because rotating the steering wheel places an extreme load on the power steering system, which can easily cause the steering gear to overheat and activate protection mechanisms, resulting in stiff steering. Reasons for heavy steering: Issues with steering fluid, excessively tight meshing clearance between the steering gear pinion and rack, damaged bearings in the steering gear or steering column, power booster failure, severe over-wear of the power steering pump belt leading to low output pressure from the steering gear pump, insufficient power steering fluid, contaminated power steering fluid, low front tire pressure, inaccurate front wheel alignment, malfunction of the speed-sensitive solenoid valve on the steering gear (which controls the power assist level), or faults in the wiring or the solenoid valve itself. Steering system inspection methods: Check the ball joint for smooth rotation in its seat—normal operation should show slight resistance without sticking, but there should be no excessive play. Inspect the tie rod's coordination with the steering gear; if the steering wheel turns significantly while the tires don't move, adjust the tightness of the tie rod ball joint pin or replace the tie rod assembly. Examine the front axle and frame for deformation or cracks—replace if cracks or excessive deformation are found. Check the tie rod for damage and the ball joint seat for spalling or cracks. If the plastic ball seat shows obvious wear, thread damage exceeding 2 threads, or the ball joint pin's tapered neck protrudes 1-2 mm above the tapered hole's upper end, replacement is necessary.

2

5

Share

Where are the accelerator, clutch, and brake located?

Accelerator, clutch, and brake positions: Automatic transmission cars have only two pedals, from left to right, they are the brake pedal and the accelerator pedal. Manual transmission cars have three pedals, from left to right, they are the clutch pedal, brake pedal, and accelerator pedal. Normally, the left foot controls the clutch, while the right foot controls the brake and accelerator. The purpose of the brake is to decelerate, either to reduce speed or to bring the vehicle to a stop. The principle of braking is to convert the kinetic energy of the car into heat energy and dissipate it. The kinetic energy comes from the power provided by the engine, which requires fuel combustion to generate. In other words, every time you press the brake, it means a little bit of gasoline is wasted.

20

5

Share

What is the fuel tank capacity of new energy vehicles?

Binyue New Energy has a fuel tank capacity of 35L, while the fuel version has 45L. The fuel tank cap is located on the left side of the vehicle body and adopts an external opening method. Introduction to New Energy Vehicles: New energy vehicles refer to automobiles that use unconventional vehicle fuels as power sources (or use conventional vehicle fuels with new on-board power devices), integrating advanced technologies in vehicle power control and driving, resulting in advanced technical principles and featuring new technologies and structures. Types of New Energy Vehicles: New energy vehicles include pure electric vehicles, extended-range electric vehicles, hybrid electric vehicles, fuel cell electric vehicles, hydrogen engine vehicles, and other new energy vehicles.

18

0

Share

Why does the bending machine cylinder rebound upward?

The upward rebound of the bending machine cylinder is caused by the movement of the cylinder piston. Bending Machine: A bending machine is a device capable of bending thin plates. Its structure mainly includes a bracket, workbench, and clamping plate. The workbench is placed on the bracket and consists of a base and a pressure plate. The base is connected to the clamping plate via a hinge. The base is composed of a housing, coil, and cover plate, with the coil placed in the recess of the housing and the top of the recess covered by the cover plate. During operation, the coil is energized by wires, generating a magnetic force on the pressure plate, thereby clamping the thin plate between the pressure plate and the base. Due to the use of electromagnetic clamping, the pressure plate can be designed to meet various workpiece requirements, and it can process workpieces with side walls, making the operation very convenient. Features of the Bending Machine: It adopts an all-steel welded structure, providing sufficient strength and rigidity; hydraulic upper transmission, with cylinders at both ends of the machine installed on the slider, directly driving the sliding work; the slider synchronization mechanism uses a torsion shaft for forced synchronization; it employs a mechanical stop structure, ensuring stability and reliability; the slider stroke can be quickly adjusted mechanically and finely tuned manually, with a counter display; a wedge-type deflection compensation mechanism ensures high bending accuracy.

15

2

Share

What is the range of WM Motor electric vehicles in kilometers?

What Causes Poor Rebound in Motorcycle Suspension?

Can OnStar start the engine without the key?

What Causes Heavy Steering Wheel When Turning in Place?

Where are the accelerator, clutch, and brake located?

What is the fuel tank capacity of new energy vehicles?

Why does the bending machine cylinder rebound upward?

Is it mandatory to wear a full-face helmet for motorcycles?

What is the reason for the seat belt not fastening?

Can the Engine Still Run if the Connecting Rod is Broken?

What Causes Engine Resonance for Over Ten Minutes When Cold?