What is the range of the Ora R1?

3 Answers
DeCourtney
07/29/25 8:25am
Ora R1 has a comprehensive range of 351km. There are two versions of the Ora R1, one with a range of 310 kilometers and the second with a range of 351 kilometers. The relevant introduction of Ora R1 is as follows: 1. Power: This car is equipped with an electric motor with a maximum power of 35kw and a maximum torque of 125 Nm. It also adopts a ternary lithium-ion battery pack provided by CATL. To improve the range of this car, it is also equipped with an economy mode, which can be switched at will during driving. 2. Configuration: This car also adds voice recognition, reversing image, electric adjustment, ECO mode. On high-configuration models, it is also equipped with daytime running lights, electronic handbrake, ESP body stability system, 6 airbags, and intelligent front-view system, further enhancing the safety of this car.
Was this review help?
8
5
Share
McNova
08/12/25 5:12am
I recently test-drove the Ora R1 electric vehicle, which has an official range of around 351 kilometers (based on CLTC standards). In real-world city driving, it can cover approximately 300+ kilometers, which is quite practical. Several factors affect the range—when I drove more aggressively, especially on highways with frequent acceleration, the range dropped to just over 280 kilometers. However, with gentle driving, such as keeping speeds below 60 km/h, the range actually approached the advertised figure. Charging is convenient, with fast charging reaching 80% in just 30 minutes, making one weekly charge sufficient for daily commutes. The battery is a ternary lithium-ion type, typically lasting about 8 years, and regular maintenance can improve efficiency. Overall, for urban commuting or weekend getaways, this range is more than adequate, offering good value for money. Electric vehicle enthusiasts would appreciate its energy-efficient design.
Was this review help?
1
2
Share
Expand All
GabrielLee
10/05/25 6:10am
As a new car owner, I've been driving the Ora R1 for a few months now, and I must say its real-world range is quite impressive. The official range is 351 kilometers, and in my daily use, I've measured it to be around 320-330 kilometers, which is more than enough for my weekly commute and grocery runs. The car is compact and nimble, making it both energy-efficient and cost-effective in the city, with electricity costs as low as a few cents per kilometer. Charging stations are easy to find, and a quick charge takes just half an hour. However, it's important to note that temperature changes can affect the range—it drops slightly in cold winters but improves significantly in summer. The long-range version offers over 400 kilometers, which is great for those who frequently travel long distances. The main reason I bought it was for peace of mind; this is what I love most about electric vehicles—no more frequent trips to the gas station.
Was this review help?
3
5
Share
Expand All
More Forum Discussions

What to Do When the Car Behind Intentionally Accelerates While Changing Lanes?

If the collision is caused by the other vehicle cutting in, it is generally the responsibility of the cutting-in party, and the rear vehicle is not at fault. Relevant explanations are as follows: 1. Cutting in itself has already affected the normal driving of the rear vehicle: It poses certain dangers to the rear vehicle, so the cutting-in party needs to bear full responsibility. However, this is on the premise that the rear vehicle intentionally collides with the front vehicle; otherwise, the driver will bear the primary responsibility, and the cutting-in party will only bear secondary responsibility. 2. For minor scrapes and collisions: It is usually difficult to provide evidence, as it is hard to determine whether the rear vehicle intentionally accelerated, making it challenging to gather evidence and impose penalties. However, this does not mean no responsibility is required. Intentionally causing a collision constitutes the crime of traffic accident. In the event of a major traffic accident resulting in serious injury, death, or property loss, criminal liability will be pursued according to the law. Additionally, in such cases, the insurance company may refuse to cover the losses.
12
3
Share

What is the fuel consumption of the Beijing 40?

Beijing BJ40's actual fuel consumption is around 8-9L. As this vehicle is positioned as an off-road SUV and considering its own weight, its fuel consumption is relatively higher compared to models in the same class. This model also offers both gasoline and diesel versions for consumers to choose from. Here are some methods to reduce fuel consumption: 1. Check the air conditioning system in summer: Air conditioning malfunctions are a significant reason for high fuel consumption. Poor cooling performance can lead to increased fan speed and lower temperature settings to achieve a cooler effect. 2. Frequent hard braking: Frequent hard braking is a primary cause of persistently high fuel consumption. While ensuring safe driving, make full use of the vehicle's inertia. 3. Avoid excessive use of air conditioning in small-displacement vehicles: For vehicles exposed to the sun, it is not advisable to turn on the air conditioning immediately after entering. First, open the windows and set the fan to a higher speed without turning on the air conditioning to expel the hot air inside the vehicle. Once the vehicle has cooled down moderately, then turn on the air conditioning.
4
1
Share

Which Material is Better for Engine Guards?

Engine guards come in the following materials: 1. Hard plastic/resin guards: These are relatively inexpensive and simple to manufacture. They can easily handle erosion from mud and sand, as well as minor scratches and scrapes to the undercarriage. However, their overall strength is inferior to steel plates. While they have some toughness, they can easily shatter under slightly severe impacts, which ironically helps the engine to sink smoothly in the event of a serious accident. It's worth noting that this material is prone to breaking, especially in winter, and once damaged, it cannot be repaired, failing to provide long-term protection. 2. Steel plate guards: The advantage of steel plate material is its strong impact resistance and low cost. In severe accidents, steel plates tend to deform rather than break, but this can interfere with the engine's safe sinking during a collision and may even cause the engine to be damaged first due to the deformation of the steel plate. Therefore, it has both advantages and disadvantages. 3. Aluminum alloy (titanium alloy) guards: The advantage of aluminum alloy (titanium alloy) guards is that they are lighter than steel guards. However, they are more expensive, lack elasticity, can hinder engine sinking, are prone to resonance, and have lower material strength. 4. Alloy plastic-steel guards: The characteristics of alloy plastic-steel material are light weight, high toughness, and strong pressure resistance. They also exhibit excellent physical properties such as rigidity, elasticity, corrosion resistance, and aging resistance.
18
2
Share

What does the vehicle's eco indicator mean?

When the eco indicator light on the dashboard illuminates, it indicates that the vehicle's economy mode has been activated. Eco is an English abbreviation derived from Ecology (environmental protection), Conservation (energy saving), and Optimization (power). The Eco mode is further divided into active eco driving mode and passive eco driving mode. When the eco indicator light on the dashboard illuminates, it indicates that the vehicle's economy mode has been activated. Eco mode is categorized into active and passive types, with the difference being that the active type has its own dedicated button, allowing the driver to choose whether to activate it. When the driver presses the Eco mode switch, the dashboard indicator light immediately turns on, and the vehicle automatically begins adjusting settings such as throttle opening, transmission shift logic, and air conditioning output power. The passive Eco mode does not have a dedicated button. When the dashboard eco indicator light illuminates, it serves merely as a reminder function. The Eco system automatically evaluates your driving behavior, and if your current driving operation achieves the optimal fuel supply, the dashboard will simultaneously display the eco indicator light. Most vehicles employ the active Eco driving mode, meaning they have their own switch button. Therefore, the Eco mode can be activated during daily driving. However, it is unnecessary to enable Eco mode when driving at speeds exceeding 120 km/h, during idle parking, in N/P gear, or in manual mode, especially when climbing hills. Doing so would not only fail to demonstrate the fuel-saving characteristics of Eco mode but also affect the vehicle's power. Additionally, the Eco mode typically becomes ineffective under the following circumstances: When the vehicle speed exceeds 120 kilometers per hour, the car prioritizes speed, causing the Eco mode to deactivate automatically. During idle parking or when in N/P gear or manual mode, the Eco mode may also become ineffective. When high torque output is required, such as when climbing a hill, the engine control unit prioritizes ensuring sufficient power to drive the vehicle, and the Eco mode will not function in such scenarios.
4
5
Share

How to Adjust the Valve Clearance of the Aowei 13L Engine?

Here are the specific methods for adjusting the valve clearance of the Aowei 13L engine: 1. Method One: Two-Step Adjustment Method. During adjustment, you can turn the screw while inserting a feeler gauge between the valve stem end and the rocker arm, moving it back and forth. When you sense slight resistance, use the cylinder-by-cylinder method to check and adjust the valve clearance, which is more precise. This adjustment method is relatively time-saving and labor-saving but requires higher skills from the maintenance personnel. 2. Method Two: Cylinder-by-Cylinder Adjustment Method. First, loosen the adjustment screw, then use a screwdriver to tighten the screw shaft. After determining the adjustment position, tighten it again, and then adjust the intake and exhaust valve clearances. Follow this method to gradually adjust the valve clearances of the other cylinders. 3. Additional Information: The purpose of adjusting valve clearance in an engine. The valve clearance adjustment in an engine is used to compensate for the expansion of the valve when heated. When the car engine is running, the valve will expand due to the increase in temperature. If the gap between the valve and the transmission component is too small, it will cause the valve to not close tightly when the valve and the transmission component are heated at high temperatures.
18
2
Share

What to do if the Audi A6L 2.4 has severe oil burning?

Audi A6L 2.4 severe oil burning measures introduction: The only solution is to repair the engine. Oil burning in motor vehicles is a serious issue. Do not simply rely on adding fuel additives to resolve the problem, as this will not completely address the oil burning issue. Only by repairing the engine, disassembling it, and addressing the specific problems can the issue be resolved without affecting usage. Below are the reasons that may cause oil burning: 1. Cold engine oil burning: When the car's temperature has not fully warmed up, the engine exhaust pipe emits a lot of blue smoke, but it returns to normal after the car warms up. This phenomenon is caused by aging valve stem seals. Due to the drop in temperature, the rubber material of the valve stem seals becomes stiff, leading to incomplete sealing. Oil leaks from the valves into the combustion chamber and burns, resulting in the above phenomenon. 2. Hot engine oil burning: After the car reaches normal operating temperature, the exhaust pipe still emits blue smoke. This indicates poor sealing of the piston rings. Due to the poor sealing of the piston rings, oil is forced by the oil pump directly through the leaking piston rings into the combustion chamber and burns, resulting in blue smoke from the exhaust pipe. There are several reasons for this phenomenon, such as material aging, carbon buildup jamming, excessive cylinder liner wear, etc.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.