What is the range of the BYD Song New Energy?

How Often Should Brake Fluid Be Replaced in a Sedan

Typically, the replacement interval for brake fluid is every 2 years or 50,000 kilometers, whichever comes first. The process of replacing brake fluid is as follows: 1. Start the engine and keep it idling, then unscrew the cap of the brake fluid reservoir. 2. Attach a transparent plastic tube to the bleeder screw of the wheel cylinder, with the other end of the tube placed into a container filled with brake fluid. 3. Loosen the bleeder valve and continuously press the brake pedal until no more brake fluid flows out, then tighten the bleeder valve. 4. Add an adequate amount of the specified brake fluid to the reservoir. Precautions for brake fluid replacement: 1. Air entering the brake system can affect braking performance. 2. Especially after replacing or topping up brake fluid, air in the hydraulic lines should be bled out. 3. During maintenance, if air enters the system due to disassembly of the hydraulic system, loose connections, or insufficient brake fluid, it should be promptly bled from the system.

14

3

Share

Reasons for Brake Master Cylinder Damage?

Reasons for brake master cylinder damage are as follows: 1. Dirty oil quality, leading to brake pipe blockage, causing excessive pressure in the master cylinder. Over time, braking becomes ineffective, and the oil pump is prone to damage. 2. Low oil quality or prolonged deterioration, making it easy to corrode the sealing rubber cup inside the master cylinder. Over time, this results in poor sealing, inability to retain oil, and loss of oil pressure. 3. Frequent lack of oil or dry grinding can cause wear on the rubber cup. 4. Frequent use of brakes can also be detrimental to the braking system. Here is more information about the brake master cylinder: 1. The brake master cylinder, also known as the "brake main cylinder" or "brake master cylinder," is a key component of the vehicle's braking system. 2. Depending on the vehicle type, it is divided into two types: air brake master cylinder and oil brake master cylinder. Generally, passenger vehicles such as cars and minivans mostly use oil brake master cylinders. 3. Commercial vehicles like trucks and tractors usually use air brake master cylinders.

14

3

Share

How to Reset the Tire Pressure Warning?

Here are the methods to reset the tire pressure warning indicator: 1. Reset the fault light to eliminate it. 2. Press and hold the SET button with the tire pressure symbol in front of the gear lever. If the tire pressure returns to normal, the warning light will be eliminated. 3. Press and hold the tire pressure monitoring button until the warning light goes off to reset it. 4. Reset it through the settings in the multifunction steering wheel or use a computer detector to reset it. The functions of the tire pressure monitoring system are as follows: 1. Prevent accidents. Safe driving is the most critical. The tire pressure monitoring system is an active safety device that can immediately alert when there are signs of danger in the tires, reminding the driver to take appropriate measures, thereby preventing serious accidents. 2. Extend tire lifespan. With the tire pressure monitoring system, the tires can always operate within the specified pressure and temperature range, reducing tire damage and extending their lifespan. 3. Make driving more economical. When the tire pressure is too low, the contact area between the tire and the ground increases, increasing friction resistance. When the tire pressure is 30% below the standard value, fuel consumption will increase by 10%. 4. Reduce wear on the suspension system. When the tire pressure is excessive, the tire's shock absorption effect is reduced, increasing the load on the vehicle's shock absorption system. Long-term use can cause significant damage to the engine chassis and suspension system.

4

3

Share

Why Does the Vehicle Body Shake at Low Speeds?

Reasons for vehicle body shaking at low speeds: 1. It may be caused by incorrect dynamic balance data of the four wheels. It is recommended to check the dynamic balance of all four wheels. If the data is incorrect, it can be readjusted. 2. It may be due to wear or looseness of the wheel bearings on all four wheels. It is advised to inspect the bearings of all four wheels. If any are loose, replacement is recommended. 3. The tire treads on the four wheels may have bulges or unevenness, causing the vehicle to shake while driving. 4. There is a high possibility that the vehicle's front suspension system has issues, but the exact cause and specific faulty component need to be determined through an on-site test drive based on your vehicle's condition.

2

1

Share

What is the maximum number of years to complete a driver's license?

The driver's license must be completed within three years. The following are the regulations during the study of subjects two and three: 1. Within the validity period of the study driving certificate, the number of scheduled exams for subject two and subject three road driving skills tests shall not exceed five times. 2. If the fifth scheduled exam is still not passed, the results of other subjects that have been passed will be invalidated. To schedule the subject two exam, the following regulations must be met: 1. For small cars, small automatic transmission cars, low-speed trucks, three-wheeled cars, small automatic transmission passenger cars for the disabled, wheeled self-propelled machinery, trolleybuses, and tram driving license types, the exam can be scheduled ten days after obtaining the study driving certificate. 2. For large buses, tractors, city buses, medium-sized buses, and large truck driving license types, the exam can be scheduled twenty days after obtaining the study driving certificate.

2

3

Share

What to Do If Resin Drips on Your Car?

Here are the solutions for removing resin from your car: 1. Use a specialized car wash liquid designed for removing asphalt to clean the resin off your car. 2. Laundry detergent has a mild and neutral property, which can quickly and effectively remove tar, asphalt, resin, and other sticky substances from the paint surface. Here are more solutions for resin on the car body: 1. If the resin on the car body is not severe, you can use hot water mixed with a small amount of laundry detergent and scrub the resin off with a brush. 2. You can use a cleaning agent to treat the resin, wash the car afterward, and then apply wax. 3. Use a volatile liquid like gasoline, soak a cloth with it, and wipe the resin off. After removing the resin, rinse the car body with clean water and apply wax for maintenance.

7

1

Share

What is the range of the BYD Song New Energy?

How Often Should Brake Fluid Be Replaced in a Sedan

Reasons for Brake Master Cylinder Damage?

How to Reset the Tire Pressure Warning?

Why Does the Vehicle Body Shake at Low Speeds?

What is the maximum number of years to complete a driver's license?

What to Do If Resin Drips on Your Car?

What are the symptoms of a bad inner tie rod end?

Engine Malfunction Light Keeps Flashing

Car Won't Start Immediately After Being Turned Off

What is the difference between Ora R1 and Ora Black Cat?