What is the purpose of wheel alignment for a car?

What are the steps to replace the key battery of the Baojun 510?

The Baojun 510 key requires a CR2032 battery when replacing. There are two types of keys, and the battery replacement process differs slightly for each: 1. Pull-out type (mechanical key): Use the release switch on the key to pull out the mechanical key. To replace the battery, first remove the mechanical key, then use a tool like a flathead screwdriver to pry open the key shell along the side gap. Once opened, the key splits into two parts: one side contains the key circuit board, and the other side holds the battery. Remove the old battery and install the new one, paying attention to the correct polarity. Then reassemble the key shell and mechanical key. 2. Folding type: First, unfold the mechanical key. Then, use a flathead screwdriver to open the upper cover at the key logo position. Next, use a Phillips screwdriver to remove the fixing screws under the upper cover and take it off. Remove the lower cover, replace the old battery with a new one, and then reassemble the covers.

15

5

Share

How to Solve Negative Pressure in a Car Fuel Tank?

Methods to solve negative pressure in a car fuel tank: Check if the carbon canister is malfunctioning, clean or replace the carbon canister. The carbon canister is a crucial component; if it becomes dirty or damaged, it can block the fuel line and cause negative pressure in the fuel tank. The fuel tank is the full name for the car fuel tank. Currently, with the development of the automotive industry and the revitalization of the domestic automotive sector, major automobile manufacturers have shown a significant increase in demand for fuel tanks. Fuel tanks can be categorized by function into ordinary fuel tanks and heated fuel tanks. Utilizing the heat energy generated by the engine during operation, a thermal circulation system is added between the engine, fuel tank, and radiator. This transforms the original single fuel tank design into a combined fuel tank consisting of a main tank and an auxiliary tank. A water heater is installed at the bottom of the fuel tank to use the heat energy generated by the engine to warm the main tank.

17

2

Share

Where is the Rear Windshield Wiper Switch Located?

The rear windshield wiper switch is located on the control lever on either side of the steering wheel. Some models have it on a separate lever, while others combine it with the front wiper controls. The position varies depending on the vehicle model. To activate the rear wiper, simply push or pull the wiper lever forward or backward. The rear wiper is designed for the rear windshield and is commonly equipped on SUVs, MPVs, hatchbacks, and some liftback vehicles. Sedans, however, have a more steeply inclined rear windshield, whereas hatchbacks have a gentler slope. Front wipers are shielded by the engine hood, which blocks high-speed airflow from affecting their operation. In contrast, rear wipers are exposed, so their installation must account for the impact of high-speed airflow. Due to the inclined rear window of sedans, the high-speed airflow during driving not only creates drag but also significantly reduces wiper efficiency.

11

1

Share

What Emission Standard Does National V Represent?

"National V" represents the fifth category of emission standards. The symbol "V" is a Roman numeral, which is the earliest form of numerical representation, originating in Rome over 2000 years before Arabic numerals. For example, Roman numerals: Ⅰ, Ⅱ, Ⅲ, Ⅳ, Ⅴ correspond to Arabic numerals 1, 2, 3, 4, 5 respectively. Below is additional information on National V: 1. The National V standard is equivalent to the Euro 5 standard in the European Union, which has been implemented since 2009. It imposes stricter limits on vehicle emissions such as nitrogen oxides, hydrocarbons, carbon monoxide, and particulate matter. Each upgrade from National I to National IV reduces vehicle pollution by 30% to 50%. After review by relevant authorities, the National V standard was implemented nationwide starting from January 1, 2017. 2. The use of new standard gasoline and diesel will reduce multiple pollutants, cutting PM2.5 emissions from National IV to National V. Environmental indicators have been further tightened, with sulfur content reduced from 50ppm to 10ppm, and fuel quality significantly improved. The draft also revised gasoline grades from 90, 93, 97 to 89, 92, 95.

5

1

Share

Where is the water temperature gauge located on the dashboard of the Volkswagen Lavida?

The water temperature gauge is not displayed on the dashboard of the Volkswagen Lavida, but some facelifted models allow the water temperature gauge to be accessed on the instrument panel by pressing the button at the end of the windshield wiper stalk. If the water temperature gauge cannot be accessed, it is not a problem, as the water temperature sensor continuously monitors the coolant temperature. If the temperature rises, an automatic warning will be triggered, and the water temperature warning light will appear on the instrument panel. Below is more information about the water temperature gauge: 1. The normal operating temperature for a car's water temperature gauge is between 80~100°C, with minor variations depending on the engine's working conditions and the season. The normal temperature typically stays around 90°C. 2. The water temperature gauge usually displays two letters, C and H (or uses white and red zones to indicate temperature ranges). C stands for "Cold," while H stands for "Hot." If the water temperature gauge approaches the H mark or the red danger zone, and in severe cases, the water temperature warning light illuminates, it indicates that the engine coolant temperature is too high.

7

4

Share

What Causes Abnormal Noises from the Wheels?

Wheels can produce the following three types of abnormal noises: 1. Clicking sound: This occurs when the tire is punctured by a nail or has a small stone stuck in it. The noise happens once per wheel rotation, resembling something "clicking" or "tapping" against the ground, with the rhythm speeding up as the vehicle accelerates. If it's a stone, simply removing it will suffice. If it's a nail, and the tire pressure is still acceptable, you can drive directly to a repair shop to fix the puncture. 2. Groaning sound: This is caused by uneven tire tread, giving the sensation that the tire is constantly running over something, producing a "groaning" or "rumbling" noise, often accompanied by steering wheel vibration and a tendency to veer left or right. In such cases, it's best to replace the tire (or rim) and avoid driving with the issue. 3. Overinflated tire noise: This results in increased tire noise. For most passenger cars, the recommended tire pressure is around 2.4 bar when unloaded (both front and rear) and around 2.6 bar for the front and 2.7 bar for the rear when fully loaded. Each vehicle may differ, so refer to the owner's manual for exact values. Overinflated tires not only produce loud noise but also make the suspension feel stiffer, leading to a bumpy ride and lighter, less stable steering. In such cases, simply release some air to adjust the pressure to the standard value.

14

1

Share

What is the purpose of wheel alignment for a car?

What are the steps to replace the key battery of the Baojun 510?

How to Solve Negative Pressure in a Car Fuel Tank?

Where is the Rear Windshield Wiper Switch Located?

What Emission Standard Does National V Represent?

Where is the water temperature gauge located on the dashboard of the Volkswagen Lavida?

What Causes Abnormal Noises from the Wheels?

How to Set Memory for Power Seats?

Where to Check the Emission Standards for New Cars?

How to Close Windows with the Key for URV?

How Often Should a Major Car Service Be Performed?