What is the purpose of the supplementary page of a driver's license?

1 Answers
DelAubrey
07/29/25 9:56pm
The supplementary page of a driver's license serves to record the license file number and related matters. If a driver's license lacks this supplementary page, it is considered invalid. Driving without this supplementary page constitutes unlicensed driving, which may result in the vehicle being impounded and the driver detained by traffic police. A driver's license, also known as a 'driving permit,' is an official document issued by government transportation authorities to individuals who meet the qualifications for driving. It typically comes in the form of a card. To obtain a driver's license, one must meet the minimum age requirement and pass a driving test. The license usually specifies the types of motor vehicles the holder is permitted to operate, such as motorcycles, passenger cars, trucks, or buses.
Was this review help?
7
4
Share
More Forum Discussions

What are the corresponding speeds for gear shifting in Subject 3?

Shift to 2nd gear when the speed is 10-20 km/h, shift to 3rd gear when the speed is 20-30 km/h, and shift to 4th gear when the speed is 30-40 km/h. The operation techniques are as follows: 1. Test requirements: Perform corresponding gear shifting operations according to the voice prompts of the test system. 2. Upshifting requirements: When upshifting, the action should be quick and gentle, the gear selection should be accurate, do not look down at the gear, and do not coast in neutral. Before upshifting, check the left and right rearview mirrors to ensure road safety, release the accelerator with your right foot first, press the clutch with your left foot, shift to the appropriate gear, then slowly release the clutch while gently pressing the accelerator to increase speed. 3. Downshifting requirements: Before downshifting, check the left and right rearview mirrors to ensure road safety. For example, when downshifting from 3rd gear to 2nd gear, release the accelerator (or press the brake) when the speed is 30 km/h, and shift to 2nd gear when the speed slowly drops to 20 km/h. 4. Gear and speed matching: During driving, keep the gear matched with the speed. Shift to 1st gear when the speed is 0-10 km/h, shift to 2nd gear when the speed is 10-20 km/h, shift to 3rd gear when the speed is 20-30 km/h, and shift to 4th gear when the speed is 30-40 km/h.
12
3
Share

How to Reset the Maintenance Reminder for Volkswagen?

Method to reset the maintenance reminder for Volkswagen: Turn off the ignition switch, press the clock adjustment button SET while turning on the ignition switch, release the SET button, press the SET button once more, turn off the ignition switch and then turn it on again to check if it has been reset. If not, the process must be restarted. Car maintenance refers to the preventive work of regularly inspecting, cleaning, supplying, lubricating, adjusting, or replacing certain parts of the car, also known as car servicing. Taking the Bora as an example, in terms of appearance, this car adopts the Volkswagen family-style front face design, with distinctively layered headlights featuring a wing-type design, giving it a strong three-dimensional feel. The rear design has changes in the outline and light clusters compared to the current model, and the body lines have become more fluid.
8
1
Share

Where is the car engine coolant located?

Car engine coolant is located in the coolant reservoir on the right side of the engine compartment. Coolant is also known as antifreeze, which prevents the coolant from freezing and cracking the radiator or damaging the engine cylinder block when the car is parked in cold seasons. Precautions for using car engine coolant: 1. Different types of antifreeze cannot be mixed; 2. Do not open the radiator cap or drain valve immediately after driving; 3. When replacing the coolant, be sure to completely remove the old antifreeze and thoroughly clean the radiator. Steps to replace car engine coolant: 1. Unscrew the radiator cap and open the radiator drain valve to release the antifreeze; 2. Flush the engine cooling system; 3. Add new antifreeze when the engine is cool, filling it up to the maximum mark on the radiator.
6
5
Share

Is the Lynk & Co 03 a domestic car?

Lynk & Co 03 is a domestic car. Here is some knowledge about Lynk & Co cars: Lynk & Co 03 model: This is a compact sedan under the Lynk & Co brand. Introduction to Lynk & Co 03: The car has a wheelbase of 2730 mm, with length, width, and height dimensions of 4639 mm, 1840 mm, and 1460 mm respectively. Three engine options for the standard version of Lynk & Co 03: These include a low-power 1.5-liter turbocharged engine, a high-power 1.5-liter turbocharged engine, and a 2.0-liter turbocharged engine. Additional knowledge about Lynk & Co 03: There is also a high-performance version called Lynk & Co 03+, which is equipped with a more powerful 2.0-liter turbocharged engine.
18
3
Share

What is the difference between a three-cylinder car and a four-cylinder car?

The differences between a three-cylinder car and a four-cylinder car are: 1. Different number of cylinders: The engine of a three-cylinder car has three cylinders; the engine of a four-cylinder car has four cylinders. 2. Different ignition intervals: The ignition sequence of a three-cylinder car is 1, 3, 2, with an ignition interval of 240 degrees; the ignition sequence of a four-cylinder car is 1, 3, 4, 2, with an ignition interval of 180 degrees. Common cylinder numbers for car engines are 3, 4, 5, 6, 8, 10, and 12 cylinders. Engines with a displacement of less than 1 liter usually use three-cylinder engines, 1 to 2.5 liters generally use four-cylinder engines, around 3 liters usually use six-cylinder engines, around 4 liters use eight-cylinder engines, and above 5.5 liters use twelve-cylinder engines.
4
1
Share

What causes the Haval M6 to not accelerate?

The main reasons for not being able to accelerate are the throttle pedal sensor and the engine control unit (ECU) issues. Throttle Pedal Sensor Problem: The throttle pedal sensor is used to detect how much the accelerator pedal is pressed. The engine control unit uses this signal to control the engine's power output. When the throttle pedal sensor fails, the engine control unit cannot receive the throttle signal, resulting in the vehicle not moving when the accelerator is pressed. Solution: Replace the throttle pedal sensor. Engine Control Unit (ECU) Problem: The engine control unit can precisely control the engine's air intake, fuel injection, and ignition based on the driver's demand. When the engine control unit malfunctions, it can cause the vehicle to not move when the accelerator is pressed. Solution: Replace the engine control unit.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.