What is the purpose of the engine start-stop system?

1 Answers
DeMelanie
07/29/25 1:25pm
Engine start-stop system functions by automatically shutting off the engine when the vehicle comes to a temporary stop during driving, and restarting it when acceleration is required. This allows the engine to enter a brief dormant state during short stops, thereby achieving fuel savings and emission reduction. The automotive engine, which first emerged in the UK, is the device that provides power to vehicles. It converts other forms of energy into mechanical energy, determining a car's power performance, fuel efficiency, stability, and environmental friendliness. Based on different power sources, engines can be categorized into diesel engines, gasoline engines, electric vehicle motors, and hybrid systems.
Was this review help?
14
0
Share
More Forum Discussions

What Causes a Car to Sway Left and Right When Driving at High Speeds?

There are several reasons why a car may sway left and right when driving at high speeds: 1. Tire issues: First, if the tires are new, performing a wheel balance and then checking for swaying can completely rule out tire problems. If the tires are old, even after performing a wheel balance, significant tire deformation or uneven wear could still cause swaying. This is because wheel balancing is adjusted using lead weights, and if the wear is uneven in the middle, a wheel balance alone won't solve the issue. 2. Incorrect four-wheel alignment: This problem is more common in older cars. The description mentions swaying, not shaking. If the issue is shaking, the suspension system, tie rods, and front wheel toe must be checked. If it's swaying, the suspension, tire pressure, and front wheel bearings should be inspected. After inspection, a four-wheel alignment must be performed.
15
2
Share

What is the distance for pulling over in Subject 3?

In the Subject 3 driving test, the effective distance for pulling over is within 30 centimeters. Below are detailed explanations about pulling over: 1. Overview: Pulling over is a clearly defined assessment item in the road test, requiring the examinee to drive the vehicle to the side and stop. 2. Precautions: Before the vehicle comes to a complete stop, opening the door to let passengers in or out is not allowed. For temporary parking on the right side, the driver must not leave the vehicle immediately and should quickly drive away if obstructing traffic. Parking is prohibited at intersections, railway crossings, curves, narrow roads, narrow bridges, steep slopes, tunnels, and within 20 meters of these locations. Parking is also not allowed on sections with pedestrian guardrails, crosswalks, construction areas, or opposite obstacles.
3
2
Share

What does the low-end version mean?

Low-end version means simplified configuration. It lacks features such as leather seats, power windows, and many electronic control functions, representing a lower level of equipment. Below are introductions to other configurations: 1. Standard version: It includes basic electric controls such as power windows, power steering, air conditioning, etc. 2. Mid-range version: Slightly more advanced than the standard version, it includes all the features of the standard version and may add extras like airbags, sunroof, leather seats, power seats, seat heating, etc. 3. High-end version: This is the top configuration, with higher specifications and usually a price about 1/3 higher than the low-end version. It can be considered the flagship model of the series, often distinguishable by exterior features like alloy wheels, tires, emblems, etc. It may also include additional electronic components such as enhanced suspension, navigation systems, onboard computers, panoramic sunroofs, EPS, and more.
1
5
Share

What is Wheel Camber?

Front wheel camber refers to the outward tilt of the top of the front wheel after installation. An angle is formed between the wheel's rotational plane and the vertical longitudinal plane, known as the front wheel camber angle. Below is a detailed introduction about wheel camber: 1. Overview: When viewed from the front or rear, the tire is not installed vertically but slightly tilted, forming a "V" shape, which is called negative camber. When tilted in the opposite direction, it is referred to as positive camber. 2. Function: Its main purpose is to make steering easier, keep the wheel close to the inner bearing of the hub to reduce the load on the outer bearing and hub nut, which is beneficial for safe driving.
3
5
Share

How to Solve Fogging on the Outside of Car Windows?

Solutions for fogging on the outside of car windows are as follows: 1. Anti-fog spray method: Spray a small amount of defogger on the car window and wipe it clean to remove dirt and stains. While polishing the glass, a thin transparent protective film is formed on the glass, which can effectively prevent the condensation of water vapor on the glass and the formation of fog. 2. Air conditioning cooling method: Use the cooling effect of the air conditioning to reduce air humidity, thereby removing window fog. In winter, especially when many people are in the car, if the air conditioning is not turned on in time, the windshield will quickly fog up, severely obstructing the driving view. Using the air conditioning's dehumidification function can remove fog on the windshield. 3. Air conditioning heating method: Use the method of reducing temperature difference to eliminate fog. Quickly increase the temperature of the front glass to reduce the temperature difference between the inner and outer surfaces of the window glass, which can effectively prevent excessive fogging on the windshield.
18
3
Share

What are the differences between gasoline and diesel cars?

The differences between gasoline and diesel cars are as follows: 1. Ignition method: Gasoline engines rely on spark plugs to ignite the compressed air-fuel mixture, while diesel cars achieve spontaneous combustion of the mixture by compressing it to the fuel's ignition point. 2. Compression ratio: Gasoline engines use spark ignition, whereas diesel cars use compression ignition, resulting in a higher compression ratio for diesel cars. Typically, diesel cars have a compression ratio of 15-18, while gasoline cars have a ratio of 8-11. Gasoline engines have a relatively lower compression ratio and operate more smoothly. 3. Material differences: Due to their higher compression ratio, diesel cars use heavier steel materials, whereas gasoline cars generally use lighter aluminum alloys, making them more compact, lightweight, and capable of higher speeds. Gasoline engines can reach speeds of 5500r-7000r, while diesel cars usually operate around 4000r. 4. Power characteristics: Diesel engines, with their lower speed, produce higher torque, making them more suitable for heavy-duty tasks and cargo transport, commonly seen in industrial machinery and off-road vehicles. Gasoline engines, with their higher speed, are better suited for high-speed driving.
8
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.