What is the purpose of the Binyue Side Assist System?

1 Answers
DiAmir
07/30/25 2:38am
The Binyue Side Assist System can detect vehicles up to 15 meters behind to prevent potential hazards. More details about the Binyue are as follows: 1. The Binyue is equipped with a wealth of safety and technology features, including ICC Intelligent Cruise Control, APA Full-Automatic Intelligent Parking System, AEB City Pre-Collision Safety System, PPS Pedestrian Recognition and Protection System, and L2-level intelligent driving among other advanced configurations. 2. The PPS Pedestrian Recognition and Protection System can effectively identify pedestrians in complex road conditions such as urban areas to avoid pedestrian collision accidents. 3. The APA Full-Automatic Parking System enables horizontal and vertical parking as well as horizontal parking exit functions, with no need to control the steering wheel, throttle, or brakes during the process.
Was this review help?
4
4
Share
More Forum Discussions

What to Do When Driving into High-Voltage Power Lines

When driving into high-voltage power lines, you should slowly and alternately move your feet away in small steps, avoiding large strides. Here are some relevant driving tips: 1. Precautions: Strictly adhere to traffic regulations, maintain good control of the steering wheel while driving, perform proper car maintenance before departure, and be cautious when driving at night as a beginner. Ensure that the vehicle's license plate is displayed, along with the inspection qualification mark and insurance mark, and always carry the vehicle's registration certificate. 2. Techniques: When meeting another vehicle at night, proactively switch to low beams and avoid using high beams to illuminate oncoming vehicles. If you are blinded by the high beams of an oncoming vehicle and cannot see the road clearly, stop and wait until visibility improves before proceeding.
15
3
Share

How to Perform Emergency Braking in One-Pedal Mode?

To perform emergency braking in one-pedal mode, simply press the vehicle's brake pedal directly when the vehicle is set to one-pedal mode. Relevant information is as follows: 1. Note: In case of an emergency, you can immediately release the accelerator pedal and press the brake pedal to perform emergency braking, preventing accidents. 2. One-Pedal Mode: The one-pedal mode in vehicles is a relatively new feature. In this mode, pressing the accelerator pedal increases the vehicle's speed. To decelerate, gently lift the pedal, which will reduce the vehicle's speed. If the driver needs to perform emergency braking, the brake pedal can also be used for control.
15
1
Share

Where to Repair Car Paint Scratches?

You can go to a paint touch-up center that offers quick scratch repair services. Alternatively, car beauty shops, repair shops, or 4S stores are also viable options. The methods for handling scratches are as follows: 1. Hairline Scratches: For hairline scratches, polishing or applying a rubbing compound is usually sufficient to remove them. A gentle wipe is often enough to make the hairline scratches disappear. 2. Light Scratches: For light scratches, just a tube of toothpaste is needed. Toothpaste is highly effective for shallow scratches that haven't damaged the car's primer. It works particularly well on marks left by other vehicles' paint during minor collisions or residues from sticky products like adhesive tapes, most of which can be completely wiped away. 3. Moderate to Deep Scratches: Moderate and deep scratches cannot be repaired by rubbing. For small dents with a depth not exceeding 5mm, filling with putty to level the surface followed by paint touch-up is recommended.
3
5
Share

How to Determine if Too Much Refrigerant Has Been Added to a Car's Air Conditioning System?

Adding too much refrigerant to a car's air conditioning system can result in the following phenomena: 1. The air blown out by the outdoor unit becomes excessively hot; 2. The cooling effect of the indoor unit deteriorates; 3. The temperature of the large copper pipe is noticeably lower than that of the small copper pipe; 4. The compressor current significantly increases; 5. The fan may continue to run while the compressor shuts down due to overcurrent and overheating protection. Below are the functions of adding refrigerant to the air conditioning system: 1. The primary role of adding refrigerant is to enable cooling. Refrigerant, used as a cooling agent in air conditioners, is essential for effectively controlling indoor temperatures. 2. During the operation and use of the air conditioner, if the refrigerant level decreases or leaks, even if all other components of the air conditioner are functioning normally, the system will not be able to provide cooling or heating.
13
0
Share

Can Subject 1 and Subject 2 be learned together?

Subject 1 and Subject 2 cannot be learned together. Here are the relevant introductions about Subject 2: 1. Concept: Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment and is the abbreviation for the field driving skill test subject. It requires basic abilities in vehicle control; mastering the basic methods of field and road driving, having the ability to reasonably use vehicle control components and correctly control the spatial position of the vehicle, and being able to accurately control the vehicle's driving position, speed, and route. 2. Projects: Five mandatory tests include reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving on an S-curve (commonly known as the S-bend). Some areas also have a sixth test: high-speed card collection.
12
5
Share

What Should Be the Standard for Long-Term Fuel Trim?

Long-term fuel trim is a numerical parameter with a value range of -23% to 16%. Long-term fuel trim is derived from short-term fuel trim values and represents long-term fuel supply correction. More details are as follows: 1. If stored in non-permanent memory: Depending on the engine management system, adaptive correction values may be stored in the PCM's non-permanent memory or permanent memory. If stored in non-permanent memory, the memory is erased when the ignition is turned off, and the correction value returns to 0 upon restart. 2. If stored in permanent memory: Even when the ignition is turned off, the memory is not lost, and upon restart, the system returns to the previously memorized correction value. The memory is only erased when the battery is disconnected or the PCM fuse is removed, and it returns to 0.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.