What is the purpose of an air conditioning filter?

1 Answers
LawsonLynn
07/29/25 9:12am
The air conditioning filter serves to separate solid impurities such as dust, pollen, and abrasive particles from the air, as well as to adsorb moisture, soot, ozone, odors, carbon oxides, SO2, CO2, etc., providing strong and long-lasting moisture absorption. The air conditioning filter is a type of filter installed in the car's air conditioning system, capable of absorbing particulate matter, reducing respiratory discomfort, minimizing irritation for allergy sufferers, and protecting the air conditioning cooling system. Location of the air conditioning filter: 1. Some air conditioning filters are located beneath the front windshield of the car, covered by a drainage trough. To replace the filter, first open the engine hood, remove the clips securing the drainage trough, detach the trough, and the air conditioning filter will be visible; 2. In most household sedans, the air conditioning filter is situated in the storage compartment under the front windshield on the passenger side, making it extremely convenient to access. Simply remove the storage compartment to reveal the air conditioning filter inside.
Was this review help?
14
0
Share
More Forum Discussions

What is the speed limit for straight-line driving in Subject 3?

Subject 3 straight-line driving speed does not exceed 40 km/h. Subject 3 vehicle body distance requirements: The vehicle body must remain basically parallel to the side lines on both sides, with an error margin of no more than 30 centimeters. The steering wheel's turning degree should not exceed 5 degrees, which is about half the length of a fingernail on the steering wheel, so only a slight force is needed. Subject 3 straight-line driving test techniques: During the straight-line driving test, find a reference point to drive towards. It's best to maintain the positional relationship between the two unchanged during the driving process. Additionally, accelerate to the test standard speed before entering the straight-line assessment area, then proceed at a constant speed. If any deviation occurs during driving, don't panic—just adjust according to the reference point.
15
0
Share

What are the symptoms of a bad engine mount?

Engine mount failure primarily manifests as noise during vehicle startup. Below is a detailed introduction about automotive engine mounts: Overview: An engine mount is a cushion that connects the engine to the vehicle body. Most are made of rubber, while a few are hydraulic products. Under normal circumstances, engine mounts can last for more than 6 years without a specific replacement interval. However, when signs of cracking, aging, or corrosion appear on the engine mount, it must be replaced promptly. Function: The main function of engine mounts is to reduce the vibration transmitted from the engine to the vehicle frame. The rubber components in engine mounts can eliminate resonance generated during engine operation. Some mounts also feature hydraulic oil pressure relief functionality. When the mount is damaged, vibrations from the engine can cause the entire vehicle body to shake.
14
0
Share

What is the hfc4gb2.4e engine?

hfc4gb2.4e is a turbocharged engine. Principle of turbocharging: A turbocharged engine is an engine that relies on a turbocharger to increase the intake air volume. The turbocharger is essentially an air compressor. It uses the exhaust gases from the engine as power to drive the turbine in the turbine chamber, which in turn drives the coaxial impeller. The impeller compresses the fresh air delivered through the air filter pipe and then sends it into the cylinder. When the engine speed increases, the exhaust gas discharge speed and turbine speed also increase synchronously, thereby enhancing the air compression level. This correspondingly increases the engine's intake air volume, which in turn boosts the engine's output power. Function of turbocharging: The main function of turbocharging is to increase the engine's intake air volume, thereby enhancing the engine's power and torque, making the vehicle more powerful.
4
3
Share

Tips for Gear Shifting in Subject Three of the Driving Test

Subject Three gear shifting techniques are as follows: Upshifting: Start by upshifting, press the clutch and check if the speedometer is within the shifting range, then press the clutch down, shift up, and slowly release the clutch to prevent the car from jerking. Note that upshifting must be done step by step and cannot skip gears directly. Downshifting: When downshifting, release the accelerator. If the speed is too fast, gently tap the brake. Also, observe the speedometer. If the speed is too slow, you can directly skip gears when downshifting. Whether upshifting or downshifting, do not use excessive force when operating the gear lever. Shifting gears does not require strength; you only need to accurately engage the gear. If you are not familiar with the gear positions, practice shifting more.
1
0
Share

What are the new regulations for vehicle annual inspections?

New regulations for vehicle annual inspections have introduced relaxed policies for different types of vehicles. New rules for small and micro vehicles: For small and micro non-operational passenger vehicles, inspections are required once every 2 years within the first 6 years, once every year after exceeding 6 years, and twice every year after exceeding 15 years. For operational passenger vehicles, inspections are required once every year within the first 5 years and once every 6 months after exceeding 5 years. New rules for large trucks: For trucks and large or medium non-operational passenger vehicles, inspections are required once every year within the first 10 years and once every 6 months after exceeding 10 years. For motorcycles, inspections are required once every 2 years within the first 4 years and once every year after exceeding 4 years. New rules for inspection timing: The timing of vehicle annual inspections is determined based on the initial registration date of the vehicle. For example, if the registration date on the vehicle's license is June 2007, the annual inspection should be conducted every June.
9
5
Share

Do traffic violations still need to be handled for scrapped sedans?

If a car is scrapped, traffic violations must still be handled. Failure to do so may affect the owner's credit. Not handling these violations can cause inconvenience in daily life. If pending scrapped vehicles have unresolved violations, the owner may be urged to pay fines, and it could even affect other vehicles under the same household name. Vehicles with outstanding violations cannot be scrapped. If the owner plans to purchase a new car, these violations must be resolved; otherwise, the old vehicle cannot be scrapped, and the original license plate cannot be deregistered. When applying for scrapping, the owner must bring the driver's license, vehicle registration certificate, and ID card. For company-owned vehicles, the business license is also required, while passenger vehicles must present their road transport permit and rural passenger transport certificate to the scrapping center. If the application is successful, the scrapping center will tow the vehicle away for free. Vehicles that are refused cannot be scrapped.
11
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.