What is the PSA car brand?

What are the three required certificates for a motorcycle?

Motorcycle three certificates refer to the vehicle license, driver's license, and compulsory insurance identification. The following are detailed introductions: 1. Vehicle license: The motor vehicle license is the legal document that permits the vehicle to drive on roads within China. The vehicle license consists of three parts: the license holder, main page, and supplementary page. The front of the main page contains the certified core with annotations, while the back has the vehicle photo, both sealed in plastic. The supplementary page is the annotated certified core. 2. Driver's license: The full name is motor vehicle driver's license, also known as 'driving license', which is the certificate required by law for motor vehicle drivers. Driving a motor vehicle requires certain driving skills, and those lacking such skills may cause traffic accidents if they drive arbitrarily. Driving without a license is prohibited.

7

0

Share

What does GCU-R fault mean?

GCU-R fault means relay sticking/short circuit or overload, just replace it with a new one. The following is a detailed introduction to automotive relays: 1. Function: The basic function of an automotive relay is to use small current to control large current operation as an "automatic switch". It plays roles in automatic regulation, safety protection, circuit conversion, switching, etc. in circuits. 2. Selection by usage environment: The usage environment conditions mainly refer to temperature (maximum and minimum), humidity (generally refers to the maximum relative humidity at 40 degrees Celsius), low air pressure (can be ignored below 1000 meters altitude), vibration and impact. In addition, there are requirements for packaging methods, installation methods, dimensions and insulation. Due to different materials and structures, relays can withstand different environmental mechanical conditions. Using beyond the product standard's specified environmental mechanical conditions may damage the relay. Select according to the equipment's environmental mechanical conditions or higher conditions.

12

5

Share

Why does the motorcycle jerk when accelerating?

Motorcycle jerking during acceleration is caused by intermittent ignition or a clogged carburetor. Here are detailed explanations about the carburetor: 1. Introduction: The carburetor is a mechanical device that mixes a certain proportion of gasoline with air under the vacuum generated by the engine operation. As a precise mechanical device, it utilizes the kinetic energy of the incoming airflow to atomize the gasoline. Its crucial role for the engine can be likened to the "heart" of the engine. A complete carburetor assembly should include starting device, idle device, medium load device, full load device, and acceleration device. 2. Classification: Carburetors are divided into simple carburetors and complex carburetors. They can also be categorized as downdraft type and side draft type. From the perspective of throttle type, carburetors can be further classified into rotary type and lift type.

7

3

Share

What is the SPN3226 fault?

SPN3226 fault code indicates that the emissions are not up to standard, and the urea supply system needs to be checked for proper functioning. Below is the relevant introduction: 1. Name Origin: The technical name for automotive urea is Diesel Exhaust Fluid (DEF), commonly referred to in China as automotive urea, vehicle urea, or vehicle denitrification agent. Automotive urea solution was first used in Europe, where it is called AdBlue, while in North America, it is known as DEF (Diesel Exhaust Fluid). It should be noted that there are urea manufacturers abroad with AdBlue and DEF certifications, which adhere to strict international standards, whereas very few domestic enterprises in China have obtained AdBlue or DEF certification. 2. Composition: Automotive urea solution is a colorless, transparent, and clear liquid with a concentration of 31.8% to 33.2%, used for reducing NOx emissions. Currently, the automotive urea solution in use is generally composed of 32.5% high-purity urea and 67.5% deionized water.

14

0

Share

What is the small light below the car headlight called?

The small light below the car headlight is called a fog light. Here are specific details about fog lights: Types: In addition to the front high beams, low beams, headlights, and small lights, and the rear running lights and brake lights, most cars also have a set of fog lights installed in inconspicuous locations at the rear. Rear fog lights are red signal lights installed at the rear of the vehicle to make it easier for other road traffic participants to spot the vehicle in low-visibility conditions such as fog, snow, rain, or dust. These lights have a higher luminous intensity than tail lights. Position: Fog lights are installed at the front of the car, slightly lower than the headlights, and are used to illuminate the road during rainy or foggy weather. Because visibility is low in foggy conditions, the driver's line of sight is limited. The lights can increase the visible distance, especially yellow fog lights, which have strong light penetration. They enhance the visibility for both the driver and other traffic participants, allowing approaching vehicles and pedestrians to spot each other from a greater distance.

17

4

Share

What does 'one gear per clutch' mean?

Press the clutch pedal all the way down, shift into one gear, then release the clutch. When the clutch is pressed down and released, only one gear can be engaged. This is called 'one gear per clutch'. Below is relevant information about vehicle gear shifting: 1. Precautions: When downshifting, the method of double-clutching plus one blip of the throttle should be used. The principle of downshifting with throttle blip is: higher speed requires a bigger 'throttle blip', lower speed requires a smaller one; lower engine speed requires a bigger 'throttle blip', higher speed requires a smaller one; flat roads require a bigger 'throttle blip', uphill requires a smaller one. 2. Techniques: Gear shifting should be timely, accurate, smooth, and quick. When starting a car, generally use the low gear (first gear). After starting, as long as road conditions permit, quickly and timely shift up through the gears to higher gears.

17

2

Share

What is the PSA car brand?

What are the three required certificates for a motorcycle?

What does GCU-R fault mean?

Why does the motorcycle jerk when accelerating?

What is the SPN3226 fault?

What is the small light below the car headlight called?

What does 'one gear per clutch' mean?

What License is Required for New Energy Vehicles?

Why Can't the Motorcycle Key Be Inserted?

What kind of adhesive can be used to bond automotive sealing strips?

What Causes Severe Overheating in Cars?