What is the process for renewing a driver's license at Xindu Government Service Center?

What are the automatic transmission gears of the Golf?

The Volkswagen Golf is a classic hatchback compact family car launched by FAW-Volkswagen in 1974. Below is an introduction to its automatic transmission gears: 1. P (Park): Upon entering the driver's seat, you can see the position of the gear lever. After parking the vehicle, shift the gear into "P" for parking. 2. R (Reverse) and N (Neutral): "R" is the reverse gear—use it cautiously when backing up. "N" is neutral, suitable for short-term parking. 4. D (Drive) and S (Sport): "D" is the automatic forward gear, while "S" is the sport mode forward gear. 5. Manual: Additionally, the vehicle can be driven in manual mode.

14

5

Share

Can a C1 driver's license be directly upgraded to an A3?

C1 can be directly upgraded to A3. If you have held a C1 driver's license for more than one year and have not accumulated 12 penalty points in the current scoring cycle or the most recent scoring cycle before application, you can apply for an A3 upgrade. Below is the relevant information: Regulations: According to Article 15 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," those who already hold a motor vehicle driver's license and apply to add a permitted vehicle type must not have accumulated 12 penalty points in the current scoring cycle or the most recent scoring cycle before application. Those applying to add medium-sized buses, trailers, or large buses to their permitted vehicle types must also meet the following requirements: (1) For adding a medium-sized bus, the applicant must have held a license for city buses, large trucks, small cars, small automatic transmission cars, low-speed trucks, or three-wheeled cars for more than three years and must not have accumulated 12 penalty points in the three most recent consecutive scoring cycles before application. (2) For adding a trailer, the applicant must have held a license for medium-sized buses or large trucks for more than three years, or a license for large buses for more than one year, and must not have accumulated 12 penalty points in the three most recent consecutive scoring cycles before application.

18

0

Share

Where is the tire pressure monitoring displayed in the 2021 Audi Q3?

The tire pressure monitoring in the 2021 Audi Q3 is displayed on the instrument cluster. The working principle of the tire pressure monitoring is as follows: it uses pressure sensors installed in the tires to measure the tire pressure, and wireless transmitters to send the pressure information from inside the tires to the central receiver module. Tire pressure monitoring automatically monitors the tire pressure in real-time while driving and alerts the driver in case of tire leaks or low pressure to ensure driving safety. Common tire pressure monitoring methods: Direct tire pressure monitoring: Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire pressure. Wireless transmitters send the pressure information from inside the tires to the central receiver module, which then displays the tire pressure data for each tire. The system automatically alerts the driver when the tire pressure is too low or there is a leak. Indirect tire pressure monitoring: When the pressure in a tire decreases, the weight of the vehicle causes the rolling radius of that wheel to become smaller, resulting in a faster rotation speed compared to the other wheels. By comparing the differences in rotation speeds between the tires, the system monitors the tire pressure. Indirect tire pressure monitoring systems actually rely on calculating the rolling radius of the tires to monitor the pressure.

12

0

Share

Is it acceptable if the left and right sides are not equally wide when reversing into the garage?

It is considered acceptable. Below is the relevant information about Subject 2: 1. Examination standards: In the Subject 2 test, the criterion for reversing into the garage is not based on the width of both sides but rather on whether the vehicle body crosses the line. Therefore, there is no need to worry about the distance on both sides of the vehicle body. As long as the vehicle body does not cross the line, it is considered normal. 2. Reversing into the garage in Subject 2: This is the first item in the Subject 2 test. If a mistake is made in this item, the Subject 2 test will be deemed a failure. When the vehicle enters the garage, as long as the vehicle body does not cross the boundary line, the distance on both sides of the vehicle is not important. Frequent adjustments to the vehicle body may cause it to cross the line, resulting in test failure. 3. Subject 2 test items: There are five items. The first test item is reversing into the garage, the second is parallel parking, the third is stopping and starting on a slope, the fourth is turning at a right angle, and the fifth is driving through curves. When the vehicle can successfully complete the curve driving, it proves that the test has been passed, and you can check your score on your own.

11

2

Share

What causes the left side to be too wide when reversing into the left bay?

The following are the related reasons for the left side being too wide when reversing into the left bay: 1. Steering too late at the starting point: If the left side is too wide and the right side is too narrow when reversing into the left bay, it is because the steering was done too late at the starting point. Even if you don't adjust the direction and reverse in one go, the right side will still be too narrow! 2. Different turning radii for left and right turns: Due to the different turning radii of the car for left and right turns, the steering point for reversing into the left bay at the starting point usually needs to be slightly earlier than for the right bay. This applies to all test vehicle models! It is essential to improve proficiency in speed control and steering wheel operation and strengthen basic skill practice! 3. Timing is crucial: The situation where the left side is too wide and the right side is too narrow when reversing into the bay often occurs during right bay reversing. Beginners are unfamiliar with the vehicle's performance, have inaccurate judgment of the 30 cm distance, and are not very good at timing the steering at key points. A combination of these factors leads to the issue.

19

0

Share

What are the differences between new cars and used cars?

Differences between new cars and used cars: 1. Performance differences: In terms of performance, the engine and overall performance of a new car are far superior to those of a used car. 2. Differences in appearance and interior: Whether it's the exterior or interior, a new car looks much more comfortable because a used car has already been used by someone else, and the interior may be dirty and worn, while the exterior may also be slightly worse. 3. Differences in fault conditions: New cars rarely have issues, while used cars are more likely to have minor or even major problems. After all, machinery will experience wear and tear over time, and the performance of a new machine is naturally better than that of an old one.

10

4

Share

What is the process for renewing a driver's license at Xindu Government Service Center?

What are the automatic transmission gears of the Golf?

Can a C1 driver's license be directly upgraded to an A3?

Where is the tire pressure monitoring displayed in the 2021 Audi Q3?

Is it acceptable if the left and right sides are not equally wide when reversing into the garage?

What causes the left side to be too wide when reversing into the left bay?

What are the differences between new cars and used cars?

What does Porsche SC mean?

What are the functions of each button in the 2021 VV5?

What documents are required for a C1 driver's license medical examination?

How to Correct the Direction When Reversing into the Garage?