What is the problem with frequent tire pressure warnings?

2 Answers
McSavannah
07/29/25 7:10am
Tire pressure frequently warning reasons are: 1. The pressure of the four tires is not within the normal range; 2. The tire is underinflated or overinflated due to slow air leakage or puncture by a nail. Tire pressure refers to the air pressure inside the tire, and the normal monitoring value ranges between 2.2 and 2.5 bar. Methods for monitoring tire pressure include: 1. Direct tire pressure monitoring; 2. Indirect tire pressure monitoring; 3. Using an intelligent tire monitoring system for detection. The tire pressure monitoring system automatically monitors various conditions of the tires in real time by recording the rotation speed of the tires or through electronic sensors installed in the tires, providing effective safety protection for driving.
Was this review help?
4
5
Share
CooperFitz
08/12/25 10:31am
I've dealt with cars a lot, and tire pressure warnings are quite common. Usually, it's because the system sensors are overly sensitive. In cold weather, tires contract, pressure drops, or after driving and cooling down, the alarm gets triggered frequently. First, check if there's a nail causing a slow leak by spraying soapy water to see bubbles. If there's no leak, it might be the sensor battery running low, especially in cars over five years old. Don't rush to replace parts—just buy an inexpensive tire pressure gauge and check weekly, keeping it near the manufacturer's recommended psi. If the warning light stays on, try resetting the TPMS system at a professional shop. Don't ignore it, as it can lead to uneven tire wear, increased fuel consumption, and compromised driving safety.
Was this review help?
9
3
Share
Expand All
More Forum Discussions

How Often Should the Transmission Fluid Be Changed for a BMW 5 Series?

BMW 5 Series requires approximately 800 yuan for a transmission fluid change, and it is recommended to replace the transmission fluid every 80,000 kilometers. If the gear shifts smoothly and there is no significant change in transmission noise, replacement may not be necessary. Note: 1. Both manual and automatic transmissions require regular fluid changes because the transmission relies on the fluid for cooling, lubrication, and hydraulic power transfer. 2. Prolonged use of old transmission fluid will significantly degrade transmission performance, and severely contaminated fluid can lead to a series of transmission issues. 3. Only transmission fluid within its service life has fine oil molecules and maintains its anti-shear capability. The fluid forms an effective lubricating film on friction surfaces, preventing slippage, cushioning sudden impacts, ensuring smoother gear shifts, and improving overall shifting performance.
10
2
Share

What is the difference between disc and ventilated disc?

Ventilated disc and disc mainly have the following differences: 1. Different application positions: Disc brakes are mainly applied to the rear wheels, while ventilated disc brakes can be applied to all four wheels of the vehicle, any wheel is possible. 2. Different structure and material: Ventilated disc brakes have many more process holes than disc brakes, and the quality of ventilated disc brakes is lighter than that of disc brakes, but the manufacturing process and price are more expensive than disc brakes. 3. Different heat dissipation effects: The heat dissipation performance of ventilated disc brakes is stronger than that of disc brakes, because ventilated disc brakes can improve the heat dissipation effect through the holes on the disc, so the service life of ventilated disc brakes is also longer than that of disc brakes.
4
3
Share

What engine does the BMW M2 Competition use?

BMW M2 Competition uses the S55 twin-turbocharged engine with a displacement of 3.0 liters. Here is the extended information about the BMW M2 Competition: 1. The BMW M2 Competition is equipped with a 3.0L M TwinPower Turbo inline-six-cylinder engine from the S55 series, which is derived from the M3/M4 models. 2. The engine delivers a maximum power of 410 horsepower and a peak torque of 550 Nm. The maximum power is achieved at 5,230 to 7,000 rpm, while the maximum torque is available from 2,350 to 5,230 rpm. 3. The BMW M2 Competition is paired with a dual-clutch transmission, achieving an official 0-100km/h acceleration time of 4.2 seconds, which is 0.1 seconds faster than the standard M2.
15
5
Share

At what extent of tire cracks should they be replaced?

Car tires should be replaced when cracks reach the following extent: 1. Crack length exceeds 6 mm. Whether cracks on tires require replacement depends on the depth of the cracks. Cracks less than 6 mm in length can be repaired at a repair shop, while those exceeding 6 mm require tire replacement because the internal materials damaged cannot be repaired. If the repaired tire is a front tire, it is recommended to swap it with an unrepaired rear tire to minimize the risk of a blowout. 2. Presence of numerous small cracks. If the tire shows signs of aging, with countless small cracks at the base of the tread grooves or the tire sidewalls that are about to damage the tire body, the tire must be replaced immediately regardless of how long it has been used or how much it has worn.
17
4
Share

What are the main types of motors used in new energy vehicles?

New energy vehicles use motors such as DC motors and asynchronous motors. Below are the related introductions about DC motors and asynchronous motors: DC Motor: A DC motor refers to a rotating electrical machine that can convert DC electrical energy into mechanical energy or mechanical energy into DC electrical energy. It is a motor capable of mutual conversion between DC electrical energy and mechanical energy. When operating as a motor, it functions as a DC motor, converting electrical energy into mechanical energy; when operating as a generator, it serves as a DC generator, converting mechanical energy into electrical energy. Asynchronous Motor: An asynchronous motor, also known as an induction motor, is an AC motor that generates electromagnetic torque through the interaction between the air gap rotating magnetic field and the induced current in the rotor winding, thereby achieving the conversion of electromechanical energy into mechanical energy.
3
1
Share

How to remove the brake light bulb of Bestune X40?

The replacement procedure for the Bestune X40 brake light bulb is as follows: 1. Open the engine hood. The release button is located below the lower right side of the steering wheel. Press it to open the hood, then reach into the engine compartment slightly left of center towards the GS and pull the release. 2. Unscrew the screws and fasteners. 3. Remove the dust cover of the headlight. The dust cover is made of flexible rubber and can be removed directly. 4. Rotate the halogen bulb counterclockwise to remove it. Be careful when handling the bulb - ensure it's not hot before removal. 5. Screw the new bulb back in clockwise.
19
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.