Browse

Antiques Collectibles Apparel Baby Kids Items Books， Movies And Music Electronics Free Stuff Garden Outdoor Health Beauty Home Goods Home Improvement Supplies Musical Instruments Office Supplies Pet Supplies Sporting Goods Ticket Toys Games Transportation Others

Used Cars New Cars Others

Business Crafts Design And Web Events Home Improvement Legal Lessons Personal Pets Photography Repair And Technical Support Wellness Writing， Translation， And Transcription Others

Activities & Groups Artists & Musicians Classes & Lessons Events Friendship & Networking Lost & Found Rideshare Sports Teams Volunteers Travel & Travel Partners Skills & Language Swap Other

What is the Problem of Abnormal Noise in the Vehicle Rear Axle?

1 Answers

McJasmine

07/30/25 1:36am

Abnormal noise in the vehicle rear axle is caused by improper clearance in the differential housing. Below are some explanations regarding the abnormal noise in the vehicle rear axle: 1. Improper side gear clearance: Incorrect fit between the differential cross shaft journal and the differential housing, improper side clearance between the axle spline gear and the differential side gear keyway, and improper meshing clearance between the differential side gear and the planetary gear. 2. Cause analysis: Insufficient gear oil or decreased viscosity, improper adjustment of the support bearing tightness, improper adjustment of the main reducer gear engagement clearance, and excessive gear wear or damage are all reasons for abnormal noise in the vehicle rear axle.

Was this review help?

9

3

Share

More Forum Discussions

How to Replace the Wiper Blades on a Mercedes-Benz E-Class?

To remove the original wiper blades, first, lift the wipers up. Then, press the clip underneath and slide out the wiper rubber. Remove the original wiper blades from one side, but be very careful not to let the wiper arm snap back and damage the windshield. Lift the front end of the middle clip slightly to proceed with the replacement.

How to Set Up the Automatic Headlights on BMW X1?

Vehicle lights can only be turned on after ignition. The method to turn them on is very simple—just rotate the button on the light control lever. For the high beam and high beam instant-on function, first turn the light knob to the low beam position, then push the light lever forward. Press the fog light switch next to the light knob to turn on the fog lights.

How to Set Up the Reversing Radar on a Mercedes-Benz?

Mercedes-Benz reversing radar switch is located in front of the center console armrest, the second button on the left. Press the button to turn off the reversing radar, which is usually enabled by default. When you can see a reversing display with a yellow light turning red in the interior rearview mirror, it indicates the setup is complete.

How to Use Wireless Charging in Cars?

Remove any objects from the charging pad; place your phone face up above the charging symbol on the pad; a green charging symbol indicates that charging is in progress. Electromagnetic induction is commonly used, such as the Qi method for mobile phone charging, but ZTE's wireless charging for electric vehicles employs an inductive approach. Resonant charging is frequently used (most electric vehicle charging adopts this method), where the power supply device (charger) transfers energy to the receiving device.

How to Set Cruise Control on BYD Song?

On the right side of the steering wheel, press the cruise control master button (Cruise), and the cruise control indicator light on the instrument panel will illuminate. When holding down the (+RES) button, the vehicle will continuously accelerate. Release the button once the desired cruising speed is reached. When holding down the (-SET) button, the vehicle speed will decrease. Release the button once the desired speed is achieved.

How to Start the Baojun 510 When the Key Fob Battery Dies?

When the remote key fob runs out of battery, you can insert it into this slot and wait for a moment. The vehicle will then detect the presence of the key. Locate the keyhole and insert the key blade from inside the remote key fob to start the car like a conventional vehicle. Many push-to-start models use this method. When the remote key fob battery is dead, simply press the key fob against the push-to-start button.

Trending Ranking

How to Install the Sunroof Weatherstrip?

How to set the ambient lighting in Mercedes-Benz E300L to auto-color-changing mode?

What is the belt routing for the Xiali N5 alternator?

How to Remove the Headrest of a BMW?

How to Change the Owner of OnStar?

How to Use the Mercedes-Benz Vehicle Assistance System?

How to Remove Car Wheel Arch Clip Fasteners?

How to enable the locking sound for Audi Q3?

How to Fix Water Leakage from Audi A-Pillar by Yourself?

How to Adjust the Audio System in Buick Excelle?

More Forum Discussions

How to Operate an Overhead Crane?

How to Repair Honda VSA Solenoid Valve Failure?

How to Fold the Rearview Mirror of BMW 120i?

How to Open the Trunk of a Mercedes-Benz E260L?

Help

Cookie

Cookie Settings

© 2025 Servanan International Pte. Ltd.