What is the Principle of Drifting?

1 Answers
Erick
07/24/25 9:26pm
Drifting occurs when the rear wheels lose most (or all) of their grip, while the front wheels maintain their grip (losing at most a small portion, and ideally gaining additional grip). At this point, as long as there is a certain amount of lateral force on the front wheels, drifting will occur. Here is some relevant information: 1. Drifting: Drifting is a racing term that refers to a series of maneuvers where the direction the car is pointing differs significantly from its actual movement direction, causing the car to slide sideways through a turn. 2. Conditions for Drifting: Drifting occurs when static friction is converted into sliding friction. Precise control of factors such as the center of gravity, the relative angle and distance between sliding and static friction, and their magnitudes can make the drifting process controllable.
Was this review help?
17
1
Share
More Forum Discussions

Where is the diagnostic connector located on the Peugeot 408?

The diagnostic port of the Peugeot 408 is located below the steering wheel, specifically near the left knee area. There is a cover panel that can be pried open to reveal the connector. This position serves as the interface for the On-Board Diagnostics (OBD) system. The OBD system internally monitors multiple systems and components, including the oxygen sensor, emission control system, fuel system, EGR, engine, catalytic converter, particulate filter, etc. The On-Board Diagnostics system, as its name suggests, continuously monitors the operational status of the engine's electronic control system and other functional modules during vehicle operation. It employs specific algorithms to detect any abnormal conditions and stores corresponding Diagnostic Trouble Codes (DTCs) in the system's memory. The system provides valuable information for vehicle maintenance and repair. Service technicians can retrieve these fault codes using manufacturer-specific diagnostic tools, enabling rapid fault identification and reducing manual diagnostic time during vehicle servicing.
3
1
Share

Why is the Geely Emgrand one-button start not responding?

Reasons why the Geely Emgrand one-button start is not responding: 1. The car battery is dead; 2. The smart key battery is low: The start system cannot detect the weak signal from the key, replace the key battery; 3. The vehicle is in an area with strong signal interference: Place the key remote as close as possible to the start button, press the clutch pedal or brake pedal, and press the start button to start the engine. The one-button start is a button device that simplifies the starting process. The Emgrand is a compact car under Geely Auto. Taking the Emgrand 2021 UP 1.5L manual comfort model as an example, its dimensions are 4632mm in length, 1789mm in width, and 1470mm in height, with a wheelbase of 2650mm. The body adopts a 4-door, 5-seater sedan structure, with a fuel tank capacity of 50 liters and a curb weight of 1255kg.
8
2
Share

How is the fuel consumption per 100 kilometers calculated for a car?

Fuel consumption per 100 kilometers = Fuel consumption (liters) ÷ Distance traveled (kilometers) × 100. Here are the relevant details: 1. Calculation method: The usual method is to fill up the fuel tank when the fuel gauge light comes on, reset the trip odometer to zero, and then record the trip odometer reading when the fuel gauge light comes on again. Divide the amount of fuel added (in liters) by the distance traveled (in kilometers) and multiply by 100 to get the fuel consumption per 100 kilometers. 2. Variations in fuel consumption: Poor driving skills can lead to increased fuel consumption. The same car driven by different people will have different fuel consumption. Only by summarizing experience and improving driving skills can the issue of high fuel consumption due to poor driving techniques be resolved.
8
0
Share

How to Avoid Brake Failure?

Avoiding brake failure methods: In daily vehicle use, pay attention to the maintenance and care of the braking system. More information about brake maintenance is as follows: 1. Regular inspection: Periodically check the brake pedal, brake discs and pads, brake vacuum booster pump, and master cylinder. When inspecting brake pads, also examine the wear condition of brake discs or drums, and regularly check and replace brake fluid. 2. Strict requirements: Brake system maintenance must be performed by specialized maintenance personnel, strictly adhering to specified requirements to prevent major accidents. 3. Main materials for brake maintenance: The primary materials used include spray-type brake system and component cleaners, high-temperature resistant brake disc protectants, brake guide pin and wheel cylinder lubricants, brake drum lubricants and protectants, as well as commonly used sandpaper.
14
4
Share

Can you drive with a bad spark plug?

You can continue driving for a short time with a damaged spark plug, but it should be replaced promptly. Methods to determine if a spark plug is damaged: Remove the spark plug and observe its appearance to assess its condition. A normal spark plug will have an insulator skirt and electrodes that appear gray-white, gray-yellow, or light brown. A properly functioning spark plug will have a reddish-brown insulator skirt, with an electrode gap between 0.8-0.9mm and no signs of electrode burning. If the spark plug is covered in oil or deposits but is not damaged, it can continue to be used after cleaning off the oil and deposits. If the spark plug is severely damaged, showing signs like blistering at the top, black streaks, cracks, or melted electrodes, the cause of the damage should be identified. After troubleshooting, replace the spark plug with a new one. Additionally, if the spark plug appears black as if smoked, it indicates the wrong heat range was selected or the air-fuel mixture is too rich, with oil creeping up.
9
4
Share

What does it mean when the driver's lock is activated?

When the driver's lock is activated, it means the driver's door cannot be opened while all other doors remain functional. Below are relevant details: 1. Reasons for driver's lock activation: During winter, if water accidentally enters the lock mechanism during car washing, residual moisture inside the lock can freeze after closing the door, causing the driver's door lock cylinder to malfunction. 2. Precautions: Avoid slamming doors forcefully during normal use, as this can lead to internal breakage of the lock cylinder, significantly reducing its lifespan. Additionally, regular lubrication of the lock cylinder is essential, especially in humid climates where rust can seize the mechanism, preventing door opening.
18
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.