What is the price range of the Buick LaCrosse?

Reasons for High NOx Emissions in Vehicles

Vehicle NOx emissions are too high for the following reasons: 1. The DEGR system is not working properly and needs to be repaired as needed. 2. The input sensor of the ignition control system is faulty, resulting in an excessively lean air-fuel mixture. 3. The engine operating temperature is too high. 4. The intake air temperature is too high, and the intake air temperature regulation system and turbocharged intercooler system should be checked. The following are the reasons that affect excessive NOx emissions: 1. The vehicle's fuel line is blocked, the fuel injector is clogged, or the fuel injection volume is insufficient, causing the oxygen content in the engine to be too high. The CH and CO immediately discharged from the engine are too low to reduce NOx, affecting the vehicle's excessive exhaust emissions. 2. The three-way catalytic converter is faulty. After the three-way catalytic converter fails, it cannot catalyze the chemical reactions of CH, CO, and NOx, resulting in excessive vehicle exhaust emissions.

6

1

Share

How to Determine if the Ignition Coil is Damaged?

Symptoms of a damaged ignition coil include: 1. The vehicle body shakes noticeably when the car is idling. 2. Observe the exhaust pipe outlet; the exhaust gas flow shows obvious intermittency, and the exhaust pipe shakes violently, with a clear "popping" sound audible. Here is some information about ignition coils: 1. As gasoline engines evolve towards higher speeds, higher compression ratios, greater power, lower fuel consumption, and lower emissions, traditional ignition systems no longer meet the requirements. 2. The core components of the ignition system are the ignition coil and the switching device. Increasing the energy of the ignition coil allows the spark plug to generate sufficient spark energy, which is the basic condition for the ignition system to adapt to the operation of modern engines.

13

1

Share

How to Check the Production Date of Car Glass?

Methods to check the production date of car glass: 1. The production date of car glass is usually marked in the lower right corner of the window or below the trademark. It is presented in the form of a single number, and the markings on the glass can provide information such as the brand, structure, specifications, and production date of the glass; 2. In the production date of the glass, the number represents the year. The black dots on the left of the number represent the production month. Black dots on the left indicate the first half of the year, while those on the right indicate the second half of the year; 3. If the black dots are on the left, subtract the number of dots from 7 to get the production month. If the black dots are on the right, subtract the number of dots from 13.

7

2

Share

What Are the Reasons Why the Car Key Sometimes Doesn't Respond When Starting the Engine?

Car key ignition failure is generally related to issues with the car's fuel system and electrical circuit. You can troubleshoot using the following methods: 1. Insufficient fuel: When the car lacks its power source—gasoline—it naturally won't start. If the failure to start is due to running out of fuel, the solution is straightforward. You can seek help from nearby car owners to borrow fuel or arrange for towing to a gas station as emergency measures. 2. Incorrect gear position: Normally, the correct gear positions for starting an automatic transmission car are P (Park) or N (Neutral). If the driver inadvertently leaves the gear in R (Reverse) or another position, not only will the car fail to start, but it also poses a safety hazard. 3. Electrical circuit issues: Common faults that cause the car to fail to start include blown fuses, open circuits in the high-voltage coil, open circuits in the low-voltage circuit, detachment of the central ignition wire, leakage in the distributor rotor, or damaged spark plugs. These require timely repair or replacement.

12

5

Share

Where is the OBD interface of the Peugeot 408 located?

The OBD interface of the Peugeot 408 is located under the steering wheel on the left side, inside the cover panel near the left knee. Here is some information about OBD: 1. OBD translates to Chinese as: On-Board Diagnostics system. 2. To standardize the diagnosis of vehicle emissions and drivability-related faults, starting from 1996, all new cars sold in the United States must have similar diagnostic tools, fault codes, and repair procedures, i.e., comply with the OBDⅡ program regulations. With the increasing globalization of the economy and the internationalization of automobiles, as the foundation for drivability and emission diagnostics, the OBDⅡ system is being implemented and applied more widely. 3. As a system for monitoring exhaust emissions, OBD has gradually expanded its control scope in later developments. With the improvement of various vehicle sensors and electronic systems, OBD has incorporated various monitoring functions into its jurisdiction. Nowadays, the term OBD interface is commonly used because only the transmission interface of this system is visible on the vehicle, but behind it lies the entire vehicle control system.

11

0

Share

How to Step on the Accelerator for Faster Speed with CVT?

For automatic transmission cars, when the accelerator is deeply pressed, the ECU will determine whether the driver intends to overtake. Therefore, theoretically, it will automatically downshift, increasing the RPM and torque, thereby obtaining greater power to complete the overtaking. CVT transmissions are not recommended for aggressive driving. If you want to upshift, you can fully press the accelerator and then release it. After the ECU receives the signal, it will upshift and save fuel. Here is some extended information about CVT: 1. CVT stands for Continuously Variable Transmission, which is commonly used in Japanese cars. CVT does not have gears or shift forks; it only has two pulleys, a steel belt, and a gear, resulting in a speed ratio that is not discrete points but continuous values. 2. For automatic transmission cars, pressing the accelerator to the floor corresponds to the fastest acceleration. However, excessive fuel can cause the engine to rev without load, damaging the engine and shortening its lifespan.

2

0

Share

What is the price range of the Buick LaCrosse?

Reasons for High NOx Emissions in Vehicles

How to Determine if the Ignition Coil is Damaged?

How to Check the Production Date of Car Glass?

What Are the Reasons Why the Car Key Sometimes Doesn't Respond When Starting the Engine?

Where is the OBD interface of the Peugeot 408 located?

How to Step on the Accelerator for Faster Speed with CVT?

What does SCAN mean in a car?

What are the differences between automatic transmission and manual transmission?

How Often Should the Brake Pads on a Mercedes-Benz A-Class Be Replaced?

Where is the license plate 'Zhe G' from?