What is the penalty for not wearing a seatbelt in the co-driver seat of a truck?

1 Answers
LandonDella
07/30/25 3:52am
Truck co-drivers not wearing seatbelts will be fined between 20 and 200 yuan and receive a 2-point penalty. The following are relevant penalties for drivers not wearing seatbelts: 1. When driving on highways: Drivers not wearing seatbelts as required will be fined 50 yuan and deducted 2 points; 2. When driving on urban expressways: Drivers not wearing seatbelts as required will be fined 50 yuan and deducted 2 points; 3. When driving on roads other than highways or urban expressways: Drivers not wearing seatbelts as required will be fined 50 yuan without point deduction.
Was this review help?
16
0
Share
More Forum Discussions

What Causes a Piercing Buzzing Sound While Driving a Car?

Here are the specific reasons for a piercing buzzing sound while driving a car: 1. Loose door hinges or interior trim panel rattles: Loose door hinges can cause the doors to vibrate continuously due to bumps while driving, resulting in various noises, especially on uneven roads. Poorly assembled interior door panels can also cause rattling. 2. Tensioner pulley noise: Tensioner pulley noise is usually caused by excessive wear of the tensioner pulley bearing. When the tensioner pulley fails, the engine may experience timing misalignment and valve timing issues, significantly affecting the vehicle's normal operation. Therefore, it needs to be replaced promptly. If not replaced in time, the engine may experience severe shaking and wear, and it may also damage the valves, leading to serious engine component failure.
13
3
Share

The Function of Camshaft Intake and Exhaust Solenoid Valves

The camshaft intake and exhaust solenoid valves control the movement of the valve body to open or close different oil discharge ports, while the oil inlet port remains normally open. Hydraulic oil then enters different discharge pipes, and the oil pressure drives the piston of the oil cylinder. The piston, in turn, drives the piston rod, which moves the mechanical device. In this way, mechanical movement is controlled by switching the current to the solenoid on and off. The working principle of the overhead camshaft actuator solenoid valve is as follows: 1. Through the control section, force is applied to the control cam in the upper-level command for operation. 2. The camshaft position sensor then transmits this command and feeds it back to the cam operation position, providing information. The upper-level control system can make control decisions based on this feedback information, thereby achieving the control objective.
1
3
Share

Where is the diagnostic port on the C4L?

The OBD interface (diagnostic port) of the C4L is located under the small box in front of the gear shift lever. You can access the OBD interface by removing this small box. Here is some information about the OBD interface: 1. The OBD interface is a relatively important port in a car, which can be connected to a diagnostic computer. After connecting to the diagnostic computer, you can read fault codes, access the car's data stream, and even modify the ECU program. 2. The OBD interface is generally located near the driver's pedal area. When using the car, be careful not to let mud or sand enter the OBD interface, and avoid exposing it to water. Some cars require a specialized computer to read data, and a generic computer may not be able to access the data. For such vehicles, you will need to visit a 4S shop to use a specialized computer for data reading.
14
3
Share

What are the differences between a 3-cylinder engine and a 4-cylinder engine?

3-cylinder engines and 4-cylinder engines differ in the following dimensions: 1. Size and weight: The 3-cylinder engine is relatively small and light, saving space in the car and facilitating vehicle layout. The 4-cylinder engine is heavier and larger in size. 2. Fuel consumption: The 3-cylinder engine has a smaller displacement and is more fuel-efficient. The 4-cylinder engine has one more cylinder than the 3-cylinder engine, making it relatively more fuel-consuming. 3. Power: The torque platform of a turbocharged 3-cylinder engine is relatively narrow, making it prone to insufficient power. The 4-cylinder engine has relatively more sufficient power. 4. Cost: The structural design of the 3-cylinder engine is relatively simple, with lower production costs, and maintenance and repairs are also cheaper. The production cost of the 4-cylinder engine is higher.
4
1
Share

Can the X-Trail switch to four-wheel drive while driving?

The X-Trail features an all-mode intelligent four-wheel drive system, allowing you to switch between four-wheel drive and two-wheel drive at any time while driving. Four-Wheel Drive Introduction: Four-wheel drive refers to a driving form where the vehicle maintains four-wheel drive throughout the entire driving process. The engine's output torque is distributed to the front and rear wheels at a fixed ratio. This driving mode ensures excellent off-road and handling performance at all times, but it cannot adjust torque distribution based on road conditions and results in higher fuel consumption. Part-Time Four-Wheel Drive: Part-time four-wheel drive uses a computer chip to control the switching between two-wheel drive and four-wheel drive. On normal roads, the vehicle operates in two-wheel drive mode. When encountering off-road conditions or wheel slippage, the computer detects and automatically distributes power to the other two wheels. For part-time four-wheel drive mode, the quality of the control program affects the intelligence of the driving mode switching.
19
0
Share

What is the normal idle speed for a Volkswagen engine?

Under normal circumstances, the engine idle speed ranges between 500 to 850 RPM, which is considered normal. Normal driving conditions: Top gear engine speeds are as follows: when reaching 100 km/h, the speed is generally around 2800 RPM; at 110 km/h, it's approximately 3200 RPM; and at 120 km/h, it's typically 3400 RPM! Speed is proportional to RPM: The shift-up RPM is not fixed—it varies depending on conditions. It's incorrect to always shift up at the same RPM regardless of circumstances. As long as there's no lugging and sufficient power, shifting up at any RPM is acceptable. The practice of always shifting up at a single RPM is wrong. Remember that shift-up RPM is proportional to vehicle speed and throttle input intensity.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.