What is the penalty for continuously changing two lanes?

2 Answers
MirandaLee
09/08/25 6:09am
Continuous lane changing will result in a 3-point deduction. Lane changing requirements: Changing lanes involves certain risks and must be done cautiously under the premise of ensuring safety. Turn signal indication: When changing lanes is necessary, turn on the turn signal 3 seconds in advance or use hand signals to alert the vehicles behind. Lane changing precautions: Observe through the interior and exterior rearview mirrors, and look back in the direction of the lane change to assess the traffic conditions behind. Judge the safe distance of the vehicle, control the driving speed, and ensure that it does not hinder the normal driving of vehicles behind in the current lane or other vehicles in the lane you are about to enter. Safely change lanes and turn off the turn signal after completing the lane change.
Was this review help?
15
3
Share
LeVincent
09/20/25 4:44am
The penalty for continuously changing two lanes is usually quite severe because this behavior is very dangerous. I've seen many drivers drive recklessly like this, resulting in rear-end collisions or side-swipe accidents. Generally, if caught by the police or cameras, the fine may range between 200 to 500 yuan, along with around 3 penalty points. In serious cases where an accident is caused, the fine could be higher or the driver's license may be revoked. Having driven for many years, I believe safety is the top priority, and changing one lane at a time can help avoid accidents. Especially on busy roads, driving slower is more reliable—don't risk it just to save a few seconds. Developing good habits, such as signaling and checking before changing lanes, can save a lot of trouble. Remember, driving is no small matter; safety comes first—protect yourself and be responsible for others.
Was this review help?
1
0
Share
Expand All
More Forum Discussions

What does auxiliary lane mean?

Auxiliary lanes refer to the lanes on both sides of the main road that assist the main road traffic, while the main road lanes are the normal traffic lanes. The following is an introduction to the traffic rules of auxiliary and main roads: 1. Inverted triangle sign: When driving on the auxiliary road, you need to pay special attention to whether there is an inverted triangle sign on the auxiliary road. There will also be a red triangular sign on the side of the road with the word "yield" written in it, indicating that there are main road vehicles merging into the auxiliary road ahead, and you need to slow down. 2. Stop line and inverted triangle sign: There will be a stop line and an inverted triangle on the auxiliary road, which are yield signs. When you see red vehicles merging into the auxiliary road, yellow vehicles should slow down and yield before the stop line and must not cross the stop line, otherwise it may easily lead to a collision accident.
9
4
Share

What is the reason for the inexplicably high fuel consumption of the MG 6?

The reason for the inexplicably high fuel consumption of the MG 6 is that the actual comprehensive fuel consumption is related to multiple factors such as load, road conditions, driving habits, weather, wind speed, tire pressure, etc. The actual comprehensive fuel consumption should be based on the actual driving conditions. Factors affecting fuel consumption: There is a certain relationship between displacement and fuel consumption, but a higher fuel consumption does not necessarily mean a larger displacement. Relatively speaking, the size of a car's displacement does not directly correlate with its fuel consumption. In addition to displacement, factors such as the car's shape, weight, and engine technology are also important factors affecting fuel consumption. Solutions for high fuel consumption: Correct improper driving habits, maintain steady acceleration, avoid coasting in neutral, reduce the car's load, perform regular maintenance and inspections, and address any issues immediately when they are discovered.
19
4
Share

Where is the Geely Vision AC fuse located?

Geely Vision AC fuse is located under the dashboard (driver's side) and in the engine compartment (left side). Spare fuses and fuse clips are fixed inside the cabin fuse box cover. Steps to replace the fuse: Switch the power mode to ON, turn off the headlights and all accessories. Remove the fuse box cover. Use a cross screwdriver to remove the screws and replace with a new fuse. Check the small fuses in the engine compartment and inside the vehicle. If a fuse is blown, use a fuse puller to remove it and replace it with a new fuse. Precautions for replacing fuses: Replacing with a fuse of higher rated current will significantly increase the chance of damage to the electrical system. Replace with a spare fuse of the same rated current. Use the diagram to locate the problematic fuse and confirm the rated current on the fuse label.
12
1
Share

What Does Incorrect Use of Brake and Accelerator Pedals Mean?

Incorrect use of the accelerator pedal means failing to press the brake when deceleration is required or mistakenly pressing the accelerator instead, and failing to press the accelerator when acceleration is needed or mistakenly pressing the brake. Incorrect use of the brake and accelerator pedals results in an immediate deduction of 100 points, leading to a direct failure. Below is additional information: 1. Correct Procedure: Upon hearing the voice prompt "Please start," press the clutch, shift into first gear, activate the left turn signal (for more than 3 seconds), simultaneously (turn head left) check the left rearview mirror, confirm safety, honk the horn, release the parking brake, and start smoothly, then turn off the turn signal. On a slope, rolling backward during startup is prohibited. 2. Exam Failure: According to Article 44 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," each subject is tested once. If the test is failed, one retake is allowed. If the retake is not attended or is still failed, the current test is terminated, and the applicant must reschedule the test. However, the rescheduling for Subject 2 and Subject 3 must be done after ten days. If the Subject 3 safe driving knowledge test is failed, the passed road driving skill test scores remain valid.
20
1
Share

What is the solution for the brake caliper not returning to position?

Brake caliper not returning to position can be solved by thinning it with a steel file. Below are some relevant introductions about brakes: 1. Description: Brake pads are important components in a car's braking system, and they are also wear parts that need to be replaced regularly. 2. Function: When the driver presses the brake pedal, the vacuum booster provides assistance, helping the driver to press the brake pedal. After pressing the brake pedal, the master cylinder pushes the brake caliper through brake fluid, allowing the brake caliper to push the brake pads to clamp the brake disc. 3. Precautions: Brake pads, brake discs, and brake fluid need to be replaced regularly. Many car owners overlook the brake fluid during maintenance. Brake fluid is a liquid that easily absorbs water. If the water content in the brake fluid is too high, it can lead to reduced braking force and longer braking distances.
2
5
Share

What are the reasons for the loud fan noise in BMW e90 engine?

BMW e90 engine fan noise may be caused by the following reasons: Possible excessive bearing wear: Inspect the radiator and surrounding components to check for excessive bearing wear. If damaged, simply replace the bearing. Examine whether the cooling fan blades are rubbing against anything. If not, the fan is likely damaged, and replacing the fan bearing or coupler should resolve the issue. Poor fan cooling performance: This may be related to the fan belt or blade balance issues, or possibly due to a dirty radiator causing poor heat dissipation, which affects air intake volume. This leads to increased electronic fan speed and consequently louder wind noise. This problem does not affect daily usage. Clean the radiator and fan blades, and check for loose fan mounting screws. If the issue persists, directly replace the car's cooling fan.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.