What is the penalty for changing lanes without signaling on a dashed line?

1 Answers
LaylaDella
07/29/25 10:21am
Failure to use turn signals under specified circumstances results in a 1-point deduction and a fine ranging from 20 to 200 yuan. If a driver accumulates 12 points within a scoring cycle, the traffic management department of the public security authority will impound their motor vehicle driving license. The driver must then participate in road traffic safety laws and regulations training and undergo an examination as required. Below are the correct methods for safe lane changing: 1. Observe the rearview mirror of the intended lane: Check the rearview mirror in the direction you plan to change lanes, primarily to assess the density of vehicles in that lane. If there are many vehicles, especially if one flashes high beams, you should refrain from changing lanes. 2. Use turn signals: When preparing to change lanes, immediately activate the turn signal while checking the rearview mirror. On highways where speeds are high, signaling in advance alerts following vehicles. After signaling, wait a few seconds to confirm the safety of the intended lane before gently steering to change lanes. Avoid making abrupt steering movements when changing lanes.
Was this review help?
5
4
Share
More Forum Discussions

Can Flood-Damaged Cars Still Be Used?

Flood-damaged vehicles suffer severe harm to their electrical circuits, which affects later usage, but they can still be used after repairs. Below is an introduction to the classification of flood-damaged vehicles: 1. Flood Level 1: Water just reaches the vehicle chassis, and the floor may get damp, but the likelihood of significant water ingress is low, with minimal impact on interior electrical equipment. 2. Flood Level 2: Water reaches halfway up the wheels. Due to the vehicle's incomplete sealing, water begins to enter the interior. For lower sedans, the water level inside may affect the seat adjustment motors and electrical components like heating and ventilation. 3. Flood Level 3: Water almost completely submerges the tires. At this point, the interior water level will fully immerse the seat cushions and center console area, affecting a large number of electrical devices.
19
3
Share

Can a car still be used after being submerged in water?

The electrical circuits of a water-damaged car can suffer severe damage, which may affect its future use, but it can still be driven after repairs. Below is an introduction to the classification of water-damaged vehicles: 1. Flood Level 1: Water has just reached the vehicle's chassis, and the floor may become damp, but the likelihood of significant water ingress is low, with minimal impact on the electrical equipment inside the car. 2. Flood Level 2: Water has submerged half of the wheels. Due to the vehicle's incomplete sealing, water will begin to enter the interior. For lower-sitting sedans, the water level inside may affect the adjustment motors of the seats and electrical components such as heating and ventilation. 3. Flood Level 3: Water has almost completely submerged the tires. At this point, the water level inside the car will fully cover the seat cushions and the central armrest area, affecting a large number of electrical components.
19
3
Share

What is the history of Mazda?

The history of Mazda dates back to 1920. Its founder, Matsuda, started by producing wine bottle corks in Hiroshima. The company was originally named Toyo Cork Kogyo Co., Ltd., and was renamed Toyo Kogyo Co., Ltd. in 1927. In 1984, the company was named after the founder's surname, Matsuda, and the transliteration "Mazda" was adopted. More details are as follows: 1. 1931-1940: In 1931, Mazda began its involvement in automobile manufacturing by producing three-wheeled trucks. In 1940, it started producing passenger cars. 2. 1967-2002: In 1967, Mazda signed an agreement with Wankel GmbH to obtain the rights to produce rotary engines, marking the beginning of Mazda's rapid development period. From 1967 to 1979, the company produced a cumulative total of 10 million Mazda vehicles. Starting in 1987, Mazda began producing vehicles in the United States with a production capacity of 240,000 units. By 2002, Mazda had produced over 35 million vehicles in total.
13
2
Share

What Are the Reasons for Increasing Car Fuel Consumption?

Reasons for increasing car fuel consumption: engine carbon deposits, spark plug failure, oxygen sensor failure. Engine carbon deposits: Stop-and-go driving conditions in the city can increase carbon deposits, and the habit of idling to warm up the engine also contributes to carbon buildup. Many driving conditions and habits can lead to carbon accumulation. Excessive carbon deposits can affect the throttle's air intake, making the car prone to stalling; carbon deposits can also adhere to the intake tract, reducing intake efficiency and worsening the air-fuel mixture; severe carbon deposits may even occupy cylinder volume, affecting combustion quality and causing knocking. Solution: It is recommended to seek professional maintenance at a 4S shop. Spark plug failure: Spark plugs are responsible for igniting the air-fuel mixture in the cylinder. Years of operation can wear them out, leading to insufficient ignition energy and weaker sparks. Combustion in the cylinder happens very quickly, leaving no time for a slow ignition—the quality of the spark at the moment of ignition directly affects combustion quality and completeness. Solution: Replace the spark plugs. Oxygen sensor failure: If the car has reached 120,000 to 150,000 kilometers in mileage, consider replacing the oxygen sensor. The oxygen sensor is located in the car's exhaust pipe and measures the oxygen content in the exhaust gases, providing feedback to the engine's fuel injection control system. Solution: Replace the oxygen sensor or visit a professional repair shop for maintenance.
9
3
Share

What is the principle of a concrete pump truck?

Here is an introduction to concrete pump trucks: 1. Principle: The rotation of rollers squeezes the rubber tube, enabling it to suck in and discharge concrete, thereby achieving the purpose of transportation. The drive shaft 8 drives the roller frame 2 and the three rollers 4 to rotate, continuously squeezing the rubber hose 5. The vacuum suction port 6 is connected to the vacuum pump. During operation, the vacuum pump continuously extracts air, creating a negative pressure inside the pump body I. The function of the support roller 3 is to assist the squeezed hose in quickly recovering to improve the concrete suction performance. 2. Function: The concrete pump truck, also known as the boom-type concrete pump truck, is a transportation machine that installs both the concrete pump and the hydraulic folding boom on the chassis of a truck or trailer, lays conveying pipes along the boom, and finally discharges concrete through the end hose. Since the boom has functions of amplitude variation, folding, and rotation, construction workers can distribute concrete within the range of the boom. The concrete pump truck can simultaneously complete the on-site transportation and distribution of concrete in one go, featuring good pumping performance, large distribution range, high flexibility, and convenient transfer. It is particularly suitable for projects with large concrete pouring demands, super-large volumes, ultra-thick foundation concrete one-time pouring, and high-quality requirements.
12
0
Share

Is It Dangerous to Place Perfume in a Car?

Placing perfume in a car can be dangerous because prolonged exposure to sunlight or high temperatures inside the vehicle may cause the perfume to explode. Perfume contains alcohol and other soluble mixtures. Alcohol has volatile properties and is also flammable. During summer, temperatures can rise above 30°C (86°F), and some perfume bottles may have a lens-like design that intensifies sunlight concentration, accelerating alcohol evaporation. When alcohol evaporates, it turns into gas, increasing in volume. However, since the perfume bottle's volume remains unchanged, the gas pressure inside the bottle rises. If the bottle's venting holes are insufficient to release the built-up pressure, the perfume bottle may explode. To prevent such explosions, slightly loosening the perfume bottle cap can help relieve pressure from expanding alcohol vapor. Additionally, some bottles feature a convex lens design that can focus sunlight and raise temperatures, potentially igniting the alcohol. It is advisable to avoid purchasing bottles with this design.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.