What is the part that fixes the shock absorber called?

1 Answers
SanFrancisco
07/30/25 12:26am
The part that fixes the shock absorber is called the suspension control arm. What is a shock absorber: Shock absorbers are vulnerable components during vehicle use. The performance of shock absorbers directly affects the driving smoothness of the car and the lifespan of other mechanical parts. Therefore, shock absorbers should always be maintained in good working condition. Fault inspection: Drive the vehicle on rough road conditions for 10km and then stop. Touch the shock absorber housing with your hand. If it's not hot enough, it indicates there's no internal resistance in the shock absorber, meaning it's not working. At this point, you can add appropriate lubricating oil and test again. If the housing becomes hot, it means there's insufficient oil inside the shock absorber and it should be refilled; otherwise, it indicates the shock absorber has failed.
Was this review help?
11
5
Share
More Forum Discussions

What is the concept of a speed of 25 mph?

A speed of 25 mph means you can travel approximately 25 kilometers in one hour. Below is a detailed introduction to gear shifting speeds: 1. Gear positions: Start in first gear, shift to second gear after traveling a few meters, shift to third gear when the speed reaches above 20 mph but below 35 mph, shift to fourth gear when the speed reaches above 35 mph but below 45 mph, and shift to fifth gear when the speed exceeds 45 mph. 2. Precautions: When shifting gears, the clutch and throttle must be coordinated properly. Press the clutch pedal all the way down, then release the throttle pedal, and quickly shift to the corresponding gear. After shifting, release your hand immediately and avoid keeping it on the gear lever for an extended period, as this can easily damage the gear lever.
14
4
Share

What Causes Fault Codes After Disconnecting the Audi Battery?

After disconnecting the battery cables, the vehicle experiences a complete power loss, leading to a mismatch between the electronic control system and the battery, which triggers fault codes. Precautions for battery replacement are as follows: 1. Avoid contact with metal: Whether removing or installing, be careful not to touch metal when adjusting the positive battery terminal. 2. Pay attention to battery model and quality: When purchasing a battery, ensure it matches the original vehicle battery model for proper functionality. It is also recommended to use batteries from reputable brands to ensure quality. 3. Check the battery's manufacturing date: Carefully inspect the battery's manufacturing date. Generally, batteries within 3 months of production are suitable for use, while those over 6 months old may affect service life. 4. Replace without power interruption: Perform the replacement without interrupting power to avoid resetting some electronic devices in the vehicle.
18
4
Share

What type of engine oil is used in the BMW 740?

The BMW 740 uses 0W-30 engine oil. Below is relevant information about the BMW 740: 1. Introduction: The BMW (BMW) 740Li is a high-end luxury sedan produced by the German BMW company. It belongs to the "BMW 7 Series" and is exclusively manufactured in Germany. 2. Powertrain: The new 740Li is equipped with a 4.0-liter V8 engine, which is an upgrade from the previous 3.6-liter V8 engine. The facelifted new 7 Series features a more approachable exterior design. In addition to incorporating BMW's Double-VANOS dual overhead camshaft variable valve timing system, the new engine also utilizes the continuously adjustable Valvetronic electronic valve drive mechanism, significantly reducing fuel consumption and emissions. The engine delivers a maximum power output of 225 kilowatts and a maximum torque of 390 Newton-meters, accelerating from 0 to 100 km/h in just 4.6 seconds. The new i-Drive system has also been upgraded, offering faster and more convenient operation, though it remains the most complex system across all BMW models.
16
5
Share

What Causes the Steering Wheel of an Audi Car to Become Stiff?

The reason the steering wheel becomes stiff could be due to the tension of the power steering pump belt being too loose, or the power steering gear and power steering pump themselves not performing well. It is also highly likely caused by internal component wear leading to low hydraulic assistance or internal pressure leakage. It is recommended to take the car to a specialized repair shop for inspection. Below is an introduction to the power steering pump: 1. Automotive Power Steering Pump: Refers to a component that helps improve and stabilize car performance. It mainly assists the driver in adjusting the car's direction. Currently, most cars are equipped with power steering pumps, mainly including the steering power pump and the brake vacuum booster pump. 2. The Role of Power Steering: Primarily assists the driver in adjusting the car's direction, reducing the effort required to turn the steering wheel. Of course, power steering also plays a certain role in the safety and fuel efficiency of the car.
1
3
Share

How much car decal does not require registration?

If the area of the decal does not exceed 30%, there is no need to apply for change registration. Below is additional information: 1. In China, vehicle body decals are permitted, but the decal area must not exceed 30% of the total body area. It is prohibited to alter the vehicle's shape or change its original condition and uniqueness. 2. If the decal area exceeds 30%, it is necessary to apply for an alteration registration with the vehicle management office as per regulations; otherwise, it constitutes a violation. 3. Car decals cannot use colors designated for special vehicles. While vehicle owners are allowed to modify the body color, colors such as fire engine red, engineering rescue yellow, and the upper white and lower blue combination designated for national administrative law enforcement vehicles are reserved for special vehicles and cannot be used on ordinary vehicles.
8
2
Share

How to Adjust the Seats in a Chevrolet Cruze?

Chevrolet Cruze seat adjustment methods are as follows: 1. Front and rear adjustment of the driver's seat: Push the control button forward or backward to move the seat to the desired position. Release the button to lock the seat in place. 2. Height adjustment of the driver's seat: Move the front or rear part of the control button up or down to adjust the height of the front or rear part of the seat. 3. Backrest angle adjustment of the driver's seat: Push the corresponding control button (or the upper part of the control button) forward or backward to adjust the tilt angle of the seat backrest. Release the button at the desired angle to lock the position.
9
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.