What is the operation method of an automatic transmission?

1 Answers
MartinMarie
07/30/25 5:14am
The operation method of an automatic transmission is: 1. Turn the ignition key to the power position; 2. Press the foot brake and shift the gear from P to N; 3. Release the foot brake to start the engine; 4. Warm up the car while stationary; 5. Press the foot brake, shift the gear from N to D, and release the handbrake; 6. Slowly release the foot brake and gently press the accelerator to start moving. The gears of an automatic transmission are: 1. D gear refers to the drive gear; 2. R gear refers to the reverse gear; 3. P gear refers to the parking gear; 4. L gear refers to the low gear; 5. N gear refers to the neutral gear; 6. W gear refers to the snow/rain gear; 7. S gear refers to the sport mode driving gear.
Was this review help?
7
3
Share
More Forum Discussions

What are the possible reasons for water leakage under the car?

It could be due to aging or damage in certain pipes of the cooling system, a damaged radiator, or the air conditioning being turned on. Here are the specific explanations: 1. Air conditioning is turned on: If water leakage under the car is caused by the air conditioning being turned on, this is a normal phenomenon. 2. Radiator leakage: If the leakage is from the cooling system pipes or the radiator, it is recommended that car owners repair it immediately. 3. Water-cooled engine: Most cars use water-cooled engines, which rely on antifreeze circulating continuously within the engine to dissipate heat. 4. Two circulation paths for antifreeze in the engine: One is the major circulation, and the other is the minor circulation.
16
5
Share

Honda Accord Unable to Shift from P Gear

Honda Accord Unable to Shift from P Gear. You can remove the gear shift cable on the transmission, inspect the cable, and try to shift into other gears. If unsuccessful, it indicates a fault in the gear shift locking mechanism or the locking solenoid valve circuit. Below is a brief introduction to the 10th-generation Accord: 1. Engine: The 10th-generation Accord is equipped with a 1.5-liter turbocharged engine and a 2.0-liter naturally aspirated engine, paired with a CVT transmission. 2. Body Dimensions: The 10th-generation Accord measures 4893mm in length, 1862mm in width, and 1449mm in height, with a wheelbase of 2830mm.
10
0
Share

Where is the air conditioning switch in Buick?

Buick Envision's air conditioning switch is located near the center console, marked with an A/C button. Below is relevant information about the Buick Envision: 1. Powertrain: The new vehicle is equipped with a 2.0T-LTG engine with a displacement of 1998mL, which has won the Ward's 10 Best Engines award. It delivers a maximum power of 191kW (260PS) and a torque of 353Nm. 2. Exterior: The new vehicle features Buick's signature waterfall grille design. The top of the headlights incorporates LED daytime running lights, and higher trim levels will also include xenon headlights with lenses.
7
2
Share

How Much Is Half a Turn of the Steering Wheel?

Turning the steering wheel half a turn means rotating it 180 degrees. You can think of the steering wheel as a clock face. The action of turning left half a turn is as follows: the left hand starts from the 9–10 o'clock position and pulls downward, while the right hand pushes to the left, rotating 180 degrees to complete half a left turn. Simply put, it means moving the steering wheel's 12 o'clock position to the 6 o'clock position. More related information is as follows: 1. Steering Wheel Grip: Since we mentioned the clock, let's also discuss the correct way to hold the steering wheel. The left hand should grip near the 9 o'clock position, and the right hand near the 3 o'clock position. Both hands should firmly hold the wheel but remain relaxed, with thumbs resting naturally on top. When turning the wheel, the hands should alternate. When the wheel completes one full turn, the left hand turns halfway, followed by the right hand continuing the motion. 2. Tips: If you're unsure how much to turn the wheel back after steering, check if the car's logo on the wheel is upright. If the logo is upside down or tilted, it means the wheel hasn't been straightened and needs further adjustment.
19
1
Share

What does it mean when the cumulative score on 12123 is zero?

Having a cumulative score of 0 points on the Traffic Management 12123 platform indicates that no points were deducted from the driver's license during a scoring cycle. The cumulative scoring cycle for road traffic safety violations (i.e., the scoring cycle) is 12 months, with a maximum of 12 points. It is calculated from the date the driver's license was first issued and continues to cycle in this manner. Additional details are as follows: 1. Score Reset: The reset date is the issuance date on the driver's license, and the system automatically resets the score on this date each year. Starting from the "initial issuance date" of the license, each year constitutes a scoring cycle, and this cycle repeats continuously. If the points deducted within a year are relatively low, the score will automatically reset to 12 points at the start of the next cycle. Drivers who accumulate 12 points within a cycle are usually required to participate in learning activities organized by relevant authorities. 2. Examination: If a driver accumulates 12 points or more twice within a scoring cycle or reaches a cumulative score of 24 points or more, the vehicle management office must also conduct a road driving skills test within ten days after the driver passes the examination on road traffic safety laws, regulations, and related knowledge. The road driving skills test must be taken according to the highest permissible vehicle class specified on the driver's license.
20
4
Share

How to Remove the Wrench Icon on the Bora Dashboard?

To remove the wrench icon on the Bora dashboard, follow these steps: 1. While holding down the 0.0 button at the bottom right corner with your left hand, turn on the ignition with your right hand. A non-flashing wrench symbol will appear on the dashboard. 2. Release the left hand and press the button at the bottom left corner once to make the wrench symbol disappear. Additional information: 1. The Bora is a compact car under the Volkswagen brand, with dimensions of 4562mm in length, 1793mm in width, and 1468mm in height, and a wheelbase of 2614mm. 2. The Bora is equipped with two engines: a 1.4-liter turbocharged engine and a 1.5-liter naturally aspirated engine.
7
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.