What is the operation method for car touch-up painting?

2 Answers
VonTalia
07/29/25 4:06pm
The operation method for car touch-up painting is: 1. Thoroughly clean the surface to be repaired before touching up; 2. Use alcohol to remove wax film, moisture, oil stains, and rust from the area to be repaired to enhance the adhesion of the paint film; 3. Shake the touch-up pen thoroughly before use, hearing the sound of the mixing ball for at least 30 shakes; 4. Open the cap of the touch-up pen in an upright position to avoid paint spillage; 5. For deeper scratches, apply repeatedly with a brush; 6. The touched-up area may appear uneven initially. After the paint film dries completely, use 2000-grit wet sandpaper to smooth it until the surface is level with the surrounding area.
Was this review help?
1
3
Share
BrynleeRose
08/15/25 4:25am
I've been doing car repairs myself for many years, and painting requires attention to detail and sequence. First, thoroughly clean the damaged area with water and a neutral car wash detergent to remove stains, grease, or dust, then wipe it dry with a clean cloth to ensure no moisture remains. Next, start sanding—use 800-1200 grit sandpaper to gently rub the surface, removing old paint and rust marks, but avoid excessive force to prevent damaging the metal. After sanding, remove dust with a cloth or compressed air, then apply primer to prevent rust: spray a thin layer to cover the area and let it dry for about half an hour, ensuring the surface is smooth. The key is spraying the color paint—color matching must be precise. I recommend checking the vehicle's VIN code to buy the corresponding paint color. When spraying, hold the can about 20 cm away, press lightly, and apply several even layers with 5-minute drying intervals to avoid runs from excessive thickness. Finally, apply a clear coat for protection and wait for it to fully dry for 24 hours before polishing with a buffing cloth for a smooth finish. Perform the entire process in a well-ventilated area while wearing protective gear to avoid inhaling fumes. With patience, you can prevent color mismatch and bubbling issues.
Was this review help?
16
1
Share
Expand All
More Forum Discussions

What is the purpose of a shark fin antenna?

The purpose of a shark fin antenna is: 1. Security and anti-theft - The built-in structure effectively prevents antenna theft with higher safety coefficient; 2. Convenience - No need to remove the antenna during automatic car washes or when entering space-constrained areas, saving time and effort; 3. Noise reduction - Combining aerodynamic principles with aesthetic design to effectively reduce airflow noise for quieter driving; 4. Multifunctional - Compatible with FM, GPS and GSM simultaneously; 5. Easy installation - International standard aperture size, OEM product requiring no roof dismantling; 6. Enhances vehicle communication signals; 7. Reduces static electricity on vehicle surface.
8
5
Share

What is the method to lift the rear seats of a car?

The method to lift the rear seats of a car is: 1. On both sides of the rear seat headrest, near the window, there will be a pull handle; 2. Pull the handle, and the backrest of the rear seat can be folded forward; 3. Simply push the seat cushion towards the rear of the car and lift it upwards. Car seats can be categorized into three types based on their usage: driver's seat, passenger seat, and child seat. The maintenance methods for car seats are: 1. Remove the protective plastic bag promptly; 2. Install a suitable seat cover or cushion; 3. Wipe the seats regularly; 4. Frequently dust the seats; 5. Avoid placing the seats near heat sources; 6. Avoid exposing the seats to direct sunlight.
18
4
Share

What is the throttle matching channel number for Volkswagen?

Volkswagen throttle matching channel number is 060. Note: Throttle adjustment matching is only suitable for Volkswagen vehicles equipped with electronic throttle engine systems, and the Santana GLi is not within the matching range. The following is an extended introduction: 1. Basic setting content: When the ignition switch is turned on, adaptive learning can be performed between the throttle control unit and the engine control unit. 2. Basic setting process: During the throttle basic setting, the throttle actuator moves from the maximum position to the minimum position in emergency operation. The engine control unit learns the stop position of the throttle control unit and the comparison curve between the throttle potentiometer and the throttle controller sensor through adaptive learning.
15
0
Share

What type of engine oil does the Roewe RX5 use?

The Roewe RX5 uses fully synthetic 5W30 engine oil. The functions of engine oil include: lubrication, auxiliary cooling, cleaning, sealing and leak prevention, rust and corrosion protection, shock absorption, and anti-wear. Taking the 2020 Roewe RX5 as an example, it is a compact SUV with body dimensions of: length 4556mm, width 1855mm, height 1719mm, wheelbase 2700mm, and minimum ground clearance of 175mm. The 2020 Roewe RX5 is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 169PS, maximum torque of 250Nm, and maximum power of 124kW. It is paired with a 6-speed manual transmission.
3
0
Share

What is the wheelbase of the Ghost?

The standard wheelbase version of the Ghost has a wheelbase of 3295 mm, while the extended wheelbase version measures 3465 mm. Below is some information about the Ghost: 1. The Ghost is equipped with a 6.6-liter twin-turbocharged V12 engine across all models, available in two versions: a low-power variant and a high-power variant. 2. Low-power variant: It delivers 571 horsepower and a maximum torque of 820 Nm. This engine reaches its peak power output at 5000 rpm and its maximum torque at 1600 rpm. 3. High-power variant: It produces 612 horsepower and a maximum torque of 840 Nm. This engine achieves its peak power output at 5250 rpm and its maximum torque at 1650 rpm.
19
2
Share

What causes the noise from the aluminum seat of the rear shock absorber in Volkswagen?

Here are the reasons for the noise from the shock absorber: 1. Damaged shock absorber: When the vehicle's shock absorber is damaged, the coordination between its components becomes problematic, causing a rattling noise when working on bumpy roads. 2. Damaged shock absorber top mount: The front shock absorber top mount of a car is made of rubber material, primarily serving to assist the shock absorber and spring in providing cushioning and shock absorption. When the top mount is damaged due to excessive wear, it not only produces noise during operation but also generates noise when turning the steering wheel while stationary, even if the shock absorber is not engaged.
18
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.