What is the oil specification for Toyota Camry 2.4?

2 Answers
MacGenevieve
08/30/25 7:17am
Toyota Camry 2.4 normally requires 5W-30 viscosity oil for maintenance. If the mileage is high, it is recommended to use 5W-40 or 0W-40 viscosity oil for better performance. For subsequent oil changes, you can choose brands such as Mobil, Shell, Castrol, or Total. The viscosity of engine oil changes with temperature, so it's important to pay attention to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, resulting in smoother cold starts for the engine. The latter number represents the kinematic viscosity of the oil at 100°C. A higher number indicates better viscosity retention at high temperatures, meaning better lubrication performance under high-temperature conditions. The method for changing the oil in a Toyota Camry 2.4 is as follows: Wait for the engine temperature to cool down, allowing the oil to drain back into the oil pan. Loosen the drain plug with a wrench and place an oil pan underneath to collect the old oil until it stops draining. Start the engine for about 30 seconds to allow the oil in the main oil passages to flow out. Remove the oil filter using a special wrench. Apply some oil to the seal of the new oil filter and screw it on clockwise by hand. Add new oil through the oil filler cap on the engine valve cover. Typically, fill about three-quarters of a standard oil container. Start the engine and let it run for 5 minutes, checking for any leaks around the drain plug and oil filter. If leaks are found, perform necessary repairs. After stopping the engine, pull out the dipstick to check that the oil level is within the standard range.
Was this review help?
9
5
Share
VonAngelo
09/12/25 4:16am
I used to drive an older Toyota Camry 2.4 with a 2.4L engine. For maintenance, I always used SAE 5W-30 oil, changing it every 5,000 kilometers. This kept the engine running smoothly without any strange noises. I chose this grade because it suits most similar models, has good temperature adaptability, ensures quick cold starts in winter, and provides sufficient high-temperature protection in summer. Nowadays, the new oil specifications might have changed slightly, but I still recommend checking the original manual for the specific year and avoiding cheap oils. A little tip: remember to check the oil filter when changing the oil—keeping it clean can extend the engine's lifespan. Personally, I think car maintenance is like taking care of an old friend; a little extra care goes a long way in keeping it running smoothly and trouble-free.
Was this review help?
3
3
Share
Expand All
More Forum Discussions

Can Tubed Tires Be Converted to Tubeless Tires?

Tubed tires can be converted to tubeless tires. Before installing tubeless tires, first apply the special self-sealing liquid tape, then add the self-sealing liquid, and finally install the tubeless tire and inflate it. Below are the detailed explanations: Types of Tires: Car tires are generally divided into radial tires and bias-ply tires. The cords of bias-ply tires are arranged in a crisscross pattern. The carcass forms the basic skeleton of the tire, and the softness from the tread to the sidewall is consistent. With the continuous improvement of radial tires, bias-ply tires are being phased out. Function of Radial Tires: The cord ply of radial tires acts as the basic skeleton of the tire, and its arrangement direction is consistent with the radial section of the tire. Since the tire needs to withstand significant tangential forces while driving, the sidewall of the tire deforms due to the lateral force from the ground during turns, ensuring that the contact area of the outer tread remains largely unchanged. Safety of Tubeless Tires: The surface of tubeless tires is made of high-quality rubber. After inflation, the surface tension increases, forming a certain pressure on the inner surface, which enhances the self-sealing ability against punctures. If punctured, unlike regular tires that lose all air instantly, tubeless tires maintain air pressure for a certain period, ensuring safety during high-speed driving.
7
5
Share

Why Does a Diesel Engine Make Abnormal Noises?

Because the diesel engine produces a rattling noise. Below is relevant information about diesel vehicles: Precautions: Pay attention to the engine's water temperature being too high. First, move the vehicle to a well-ventilated and shady area. Open the engine hood and wait for the coolant temperature to drop. If it's necessary to open it immediately, you can use a large towel soaked in water, cover the antifreeze reservoir cap, and then try to slowly open the cap. When steam emerges, quickly move your hand away. Wait until the steam completely dissipates before finally opening the reservoir cap and adding coolant. Scrap time: The vehicle must be forcibly scrapped when the mileage reaches 600,000 kilometers, but the specific condition of the vehicle should also be considered. For commercial vehicles, they must be scrapped after 8 years. Every vehicle has its own scrap time limit from the moment it is purchased, which is a system designated by the national transportation department. That is, during the use of the vehicle, safety inspection regulations are stipulated based on the number of seats and the period of use.
3
2
Share

What is a Diesel Particulate Filter?

Diesel particulate filters are categorized into active regeneration and passive regeneration based on their working principles. Below is an introduction to diesel particulate filters: Function: Diesel particulate filters can effectively reduce particulate emissions by first capturing particulate matter from the exhaust and then oxidizing the captured particles to regenerate the filter. The so-called regeneration of the filter refers to the fact that during long-term operation of the DPF, the accumulation of particulate matter in the filter will gradually increase, leading to higher backpressure in the engine and a decline in engine performance. Working process: The diesel particulate filter (DPF) captures particles through a filtration device that combines surface and internal mechanisms, such as diffusion deposition, inertial deposition, or linear interception.
17
4
Share

How to Distinguish Between National 3, National 4, National 5, and National 6 Diesel Vehicles?

To determine whether a vehicle meets National 4 or National 5 standards, you can refer to the vehicle's fuel consumption label. Below is an introduction to National 4 standards: Introduction: The National 4 emission standard is the fourth phase of China's motor vehicle pollutant emission standards. The main pollutants emitted by vehicles include HC (hydrocarbons), NOx (nitrogen oxides), CO (carbon monoxide), and PM (particulate matter). By applying technologies such as improved catalytic converter active layers, secondary air injection, and exhaust gas recirculation systems with cooling devices, the standard aims to control and reduce vehicle emissions to below specified limits. Implementation Date: In March 2009, the Industrial Policy Department of the Ministry of Industry and Information Technology convened a meeting with relevant companies to discuss the implementation of vehicle emission standards (National 3, National 4, and National 5). Major automotive companies and engine manufacturers attended the meeting. On December 21, 2010, the General Office of the Ministry of Environmental Protection of the People's Republic of China responded to the China Association of Automobile Manufacturers with the document 'Reply on the Implementation Date of the National 4 Emission Limits for Motor Vehicles' (Huanban Han [2010] No. 1390).
18
2
Share

Can a Car Be Locked If the Engine Is Left Running?

For vehicles with a push-button start, the car cannot be locked if the engine is left running. Push-button start models require the vehicle to be in the P (Park) position and turned off to completely cut power. If the engine is turned off without shifting to P, although the engine stops running, the vehicle's power system remains active, preventing the doors from being locked. Here are some relevant details: 1. Push-Button Start: Using the push-button start when the car is in P or N (Neutral) does not harm the engine. However, turning off the engine while the car is in gear can cause damage. For safety reasons, it is recommended to press the brake pedal before using the push-button start to turn off the engine. 2. Precautions: When locking the car, ensure all power switches inside the vehicle are turned off to prevent battery drain.
10
3
Share

Can the Vehicle Inspection Sticker Be Replaced If Lost?

Annual inspection labels can be reissued if lost. Bring the original and copies of the vehicle's registration certificate and the owner's ID card to the local vehicle management office or inspection station in the city where the vehicle is registered. Below is relevant information about vehicle inspections: Regulations: New vehicles do not require on-site inspections within the first 6 years—simply collect the inspection compliance label. However, after 6 years (including the 6th year), an annual inspection is required, and the vehicle must be driven to the inspection station. Notes: For non-commercial passenger cars and other small and mini passenger vehicles (excluding vans and vehicles with 7 or more seats) registered within 6 years, every 2 years when a regular inspection is due, the vehicle owner can directly apply for the inspection label from the traffic management department of the public security authority by providing proof of compulsory traffic accident liability insurance and vehicle and vessel tax payment or exemption, without needing to undergo a safety technical inspection at an inspection station. Before applying, the vehicle owner must resolve all traffic violations and accidents related to the vehicle.
1
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.