What is the oil filter for Baojun 310?

1 Answers
OJace
07/30/25 7:31am
The oil filter model for Baojun 310 is Mann W7012. Below are the detailed specifications of the oil filter: 1. Classification: Oil filters can be structurally categorized into two types: full-flow and cartridge type. The full-flow type can be entirely unscrewed for replacement, while the cartridge type only requires replacing the filter element. 2. Composition: An oil filter typically consists of components such as the housing, filter element, bypass valve, check valve, and sealing rings. It is generally located on the main oil passage of the engine block. The engine's oil pump draws oil from the oil pan and delivers it to the oil filter. After passing through the oil filter to remove impurities, the oil flows through various passages to different parts of the engine. 3. Lifespan: Regardless of the oil's usage condition, the shelf life of an oil filter is three years. Beyond this period, the filtering capability of the filter element inside the oil filter significantly declines, making it unable to effectively filter impurities from the oil.
Was this review help?
5
4
Share
More Forum Discussions

What is the ground clearance of the Land Cruiser Prado?

Toyota Land Cruiser Prado has a minimum ground clearance of 215mm. Below are the relevant details: Introduction: Minimum ground clearance refers to the distance between the lowest protruding part of the vehicle's chassis and the level ground when the vehicle is parked on a horizontal surface under rated full load conditions. Definition: The standard for "minimum ground clearance" is GB/T3730.3-1993, which defines it as: the distance between the lowest protruding part of the vehicle's chassis and the level ground when the vehicle is fully loaded (with the maximum allowable load mass). The standard provides specific measurement methods in the form of diagrams but does not specify a specific numerical range. Minimum ground clearance reflects the vehicle's ability to pass over obstacles or uneven ground without collision.
3
3
Share

Where is the antifreeze located in a Kia K2?

The antifreeze in a Kia K2 is located in the engine compartment, where you'll find a colored reservoir - that's the antifreeze container. Here are more detailed specifications about the Kia K2: Overview: The Kia K2 is a model under Dongfeng Yueda Kia, launched during the 2011 Shanghai International Auto Show and officially released in July 2011. As Kia's second main domestically produced A0-class model, the K2's exterior design follows the brand's latest styling trends. Other features: In terms of powertrain, the K2 is equipped with either a 1.4L or 1.6L engine. The 1.6L version shares the same engine as the Forte, delivering maximum power of 90.4kW at 6300rpm and increased maximum torque of 155Nm at 4200rpm. The 1.4L engine (model G4FA) produces maximum power of 78.7kW at 6300rpm.
11
5
Share

Will Car Window Tinting Freeze in Winter?

Car window tinting can be affected by freezing in winter. The significant thermal expansion and contraction during winter, combined with dry air and extremely cold glass, makes the glass highly prone to cracking or damage if washed with warm or hot water. However, car window tinting in winter should be performed in an enclosed space to prevent dust particles from getting trapped between the glass and the film. The steps for winter car window tinting are as follows: 1. Clean the glass thoroughly with glass cleaner and let it dry. 2. Cut the window film according to the glass dimensions. 3. Use the "wet method" or "dry method" to adhere the film to the car window glass. 4. Wait for 1-3 hours before driving the car away.
14
0
Share

Can the Car Rocker Panel Be Replaced if It's Rotten?

The rocker panel of a car is an area that is prone to scratches and damage while driving, especially for models with lower chassis. Sand, mud, and rainwater constantly erode the rocker panel. Car rocker panels are generally made of aluminum or plastic, making them relatively easy to repair. As long as the damage is not severe—such as dents, paint peeling, scratches, or rust—it can usually be repaired on the original part without needing replacement. Repairing Rusted Areas by Cutting and Welding: For metal rocker panels, rusted areas can be repaired by cutting and welding. Use a grinder to cut out the rusted section of the rocker panel, then weld a similarly sized piece of sheet metal in its place. Smooth and flatten the weld points with the grinder, and finish by repainting. Whether it's rust on the rocker panel or other metal parts of the car, it is advisable to address it as soon as possible. Rust acts like an infection in a car, spreading continuously until the entire part corrodes. When a part rusts, the paint may bubble, wrinkle, or even peel off. Treatment Methods: Dents in the rocker panel are also relatively easy to handle. For plastic panels, pouring hot water over the dent may help it pop back out, or specialized pulling tools can be used. For metal rocker panel dents, they can be pulled out using a dent puller. If pulling doesn’t work, the damaged section can be cut out and a new piece welded in place.
5
0
Share

What to Do When Car Door Hinges Creak During Opening and Closing?

Car doors and the body are connected via hinges, similar to household doors. It's normal for hinges to produce creaking sounds after prolonged use. To ensure the pulleys remain smooth and quiet over time, it's recommended to apply lubricating oil every 2-3 months for maintenance. Here are some measures to prevent aging: 1. Check if the door seals have aged. Since seals are made of rubber, they will gradually deteriorate and crack over time. 2. This can lead to noticeable wind noise and friction sounds that drivers and passengers can hear. If the seals are aged or damaged, it's advisable to replace them directly. Regularly cleaning dust and rainwater from the gaps between the seals during routine car use can help prevent aging.
5
1
Share

How to Replace the Battery in a Volkswagen Tiguan Car Key?

Introduction to the method of replacing the battery in a Volkswagen Tiguan remote key is as follows: 1. Press the button on the mechanical key of the remote key to open the mechanical key. Hold the mechanical key end with your right hand, with the Volkswagen logo on the remote key facing upward. Use your left thumb to pry upward along the middle seam of the remote key, applying slight force to open one end of the battery cover. 2. Then, use your hand to open the other end of the battery cover along the lifted side, exposing the battery. 3. Insert a toothpick or other thin pointed object into the notch at the edge of the battery, and gently pry to remove the battery. The battery is a 3V CR2032 alkaline battery. Place the new battery into the battery slot, close the battery cover, and gently press the cover to ensure it is securely fastened.
1
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.