What is the normal water temperature for the New Generation Transit?

1 Answers
VanWilliam
07/29/25 10:57am
New Generation Transit's normal water temperature is 90 degrees. Normal water temperature: Water temperature refers to the coolant temperature. After the engine warms up, it typically displays 70-90 degrees as normal. When the coolant level in the radiator is low, the water temperature will rise, and it's necessary to add water at this point. If the temperature gauge approaches the H mark or the red danger zone, or if the coolant warning light illuminates in severe cases, it indicates that the engine coolant temperature is too high. Working principle: The water temperature gauge sensor is a thermistor-type sensor fixed with threads on the engine's coolant passage. The thermistor determines the current flowing through the coil winding of the water temperature gauge, thereby driving the gauge needle to swing.
Was this review help?
19
5
Share
More Forum Discussions

What does water coating mean?

Automotive water coating is a type of protective film that forms a thin layer after application, capable of resisting minor scratches. Below is relevant information about water coating: Introduction: Water coating is the simplest form of automotive coating, which quickly spreads into a film upon contact with water, hence the name "water coating." A full vehicle coating takes only 5 minutes. It prevents aging, water, stains, acid rain, and minor scratches, acting as a protective shield against vehicle aging. Function: Enhances the brightness of the car paint, forming a crystal-clear protective layer on the surface. It provides stain resistance and a glossy finish, with high-molecular polymers covering the paint to form a protective film. After each wash, the car looks as good as new.
19
5
Share

Is the air pressure the same for 1K and 2K paint spraying?

Spraying 1K and 2K paint requires the same air pressure. Spray painting air pressure: The normal air pressure for spray painting is 0.3~0.6Mpa, whether it's 1K or 2K paint spraying, the air pressure falls within this range. Therefore, the air pressure for 1K and 2K paint spraying is the same, with no difference. Definition of air pressure spraying: Air pressure spraying is a type of spraying method. It involves atomizing the paint with compressed air and spraying it from the nozzle onto the substrate (plastic or other materials). This method is suitable for coating porous materials and substrates that should not be penetrated. Spraying can be further divided into suction-type spraying and pressurized air spraying.
4
5
Share

Where are the motors used in domestically produced Teslas manufactured?

Tesla's electric motors are independently designed and developed, and produced in Nevada, USA. Tesla is an automobile manufacturer from Silicon Valley, USA, and its vehicle models include the Model 3, Model S, Model X, Model Y, and others. Below is an introduction to the Model 3: 1. Overview: The Model 3 is Tesla's entry-level model, a pure electric mid-size sedan. 2. Body dimensions: The wheelbase is 2875 mm, and the length, width, and height are 4694 mm, 1850 mm, and 1443 mm, respectively. 3. Suspension: The front suspension uses a double-wishbone independent suspension, and the rear suspension uses a multi-link independent suspension. The double-wishbone suspension consists of upper and lower wishbones with a linkage between them. This design can reduce body roll and minimize brake dive. The multi-link suspension enhances the tire's contact with the road, thereby improving traction.
14
0
Share

What is the horsepower output of Chery's twin-cylinder EFI engine?

The horsepower output of Chery's twin-cylinder EFI engine is 218 hp. Definition of horsepower: Horsepower is a commonly used unit of power measurement in engineering. It generally refers to metric horsepower rather than imperial horsepower. It is conventionally agreed that 1 metric horsepower equals the work done to lift a 75 kg object 1 meter per second. Metric horsepower defines 1 metric horsepower as the work of 75 kilogram-force meters completed in 1 second. That is: 1 metric horsepower = 75 kilogram-force meters/second = 735 watts. Main characteristics of horsepower: lightweight structure, easy mobility, simple installation, minimal vibration, smooth operation, easy management, fuel-efficient, and easy starting. It is currently the most widely used and highest-volume engine type, with good starting performance and low fuel consumption.
18
1
Share

What are the features of the Sylphy Yuexiang Edition?

The features of the Sylphy Yuexiang Edition are as follows: 1. Configuration: Equipped with an 8-inch floating LCD touch screen, built-in driving recorder, automatic air conditioning, and a new ultra-intelligent connectivity system, as well as voice control for the vehicle, remote start, and other functions. 2. Exterior: The sporty appearance far surpasses the older models, appearing more youthful and dynamic. The segmented waistline on the side is very distinctive, with a slightly increased body length and slightly reduced height, giving it a more poised stance. The interior design and quality significantly surpass the older models, comparable to the former Mercedes-Benz A-Class. 3. Safety: Equipped with seven safety systems and three driving assistance technologies, including lane change assist, lane departure warning, fatigue driving reminder, active braking, and side parking radar, enhancing safety.
1
4
Share

Why does the new horn sound muffled?

New horn sounds muffled for the following reasons: Insufficient battery power: Check the output voltage of the magneto and whether the power is sufficient. When the horn button is pressed, if the horn sounds hoarse, it indicates insufficient battery charge. Horn malfunction: When the power supply is normal, remove the horn's live wire and test for sparks by scratching it against the ground. If there are no sparks, the fault lies between the horn button and the terminal block; if there are sparks, the fault is in the horn. Horn contact burn or poor contact: This can be caused by burnt or poorly connected horn contacts, damaged vibration diaphragm, or incorrect adjustment of the working gap between the vibration disc and the vibration diaphragm. Note: Be extremely careful when checking the circuit to avoid unnecessary short circuits that could burn out the wiring.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.