What is the normal water temperature for the Haval H9?

1 Answers
McEliza
07/30/25 3:38am
The normal water temperature range is between 90 to 100 degrees on the temperature gauge. Below are related details: 1. In case of overheating due to coolant loss, you can add a small amount of distilled water as an emergency measure. For overheating caused by prolonged driving, pull over safely, turn on the hazard warning lights, and allow the vehicle to cool down naturally. 2. The car dashboard is a device that reflects the working conditions of various vehicle systems. Common indicators include the fuel light, washer fluid light, electronic throttle light, front and rear fog light indicators, and warning lights. Dashboards vary by car model, but conventional gauges typically include the speedometer, tachometer, oil pressure gauge, water temperature gauge, fuel gauge, and charging gauge. 3. The water temperature gauge sensor is a thermistor-type sensor, threaded into the engine's cooling water passage. The thermistor determines the current flow through the gauge's coil windings, which drives the needle movement. In the past, tap water was used as engine coolant, but modern vehicles often use specialized coolant, hence it's also referred to as the coolant temperature gauge.
Was this review help?
2
4
Share
More Forum Discussions

How to Cancel the Tire Pressure Warning on the Bora?

To eliminate the tire pressure warning on the Bora, follow these steps: 1. There is a tire monitoring indicator button on the central console. After the system issues a low tire pressure warning, the vehicle must remain stationary for about one minute. Do not move the car or turn off and restart the ignition switch until pressing the button to recalibrate the tire monitoring indicator. 2. Find the tire pressure reset option in the settings on the central display. If the above methods do not work, it is necessary to visit a 4S shop to eliminate the tire pressure warning. The reasons for the tire pressure warning light to illuminate are as follows: 1. The pressure in one or more tires is significantly lower than the set pressure, or the tire structure is damaged. Additionally, the system will emit a warning sound, and the combination instrument display may show a corresponding text message. 2. System malfunction, the indicator light remains on.
10
0
Share

What car has a logo with five sticks?

The car with a logo featuring five sticks is WM-Motor. 'WM' is the abbreviation of the German word 'Weltmeister,' which means world champion, signifying WM-Motor's ambition to produce intelligent vehicles of 'world champion' caliber. Here is some relevant information about WM-Motor: 1. The WM-Motor logo consists of five vertical lines, each representing cloud services, platforms, people, vehicles, and multi-channel operations. These five elements embody WM-Motor's production and sales philosophy, with the five lines continuously interacting and interconnecting. 2. WM-Motor specializes in manufacturing new energy vehicles and was established in January 2015. The company originated from an electric powertrain system R&D enterprise founded by co-founder Du Ligang in 2012.
10
4
Share

How to adjust the height of the seat in Baojun 510?

Baojun 510 features a 4-way electric seat adjustment. Simply press the button located below the left side of the driver's seat to adjust the seat height up and down. Here is some information about the Baojun 510: 1. The Baojun 510 is positioned as a compact SUV, adopting a new family-style design. The headlights feature a split layout, with slim and sharp LED daytime running lights on top and hexagonal headlights below for low and high beams. 2. The side of the car features a high waistline design, and the currently popular floating roof is also applied. The new car measures 4220mm in length, 1740mm in width, 1615/1625mm in height, with a wheelbase of 2550mm.
6
3
Share

What to do if the steering wheel is still off-center after wheel alignment?

If the steering wheel is not straight after wheel alignment, it is definitely necessary to seek professional help from an auto repair shop or a 4S store, as this issue cannot be resolved on your own and requires the support of mechanical equipment. You can try performing wheel alignment and wheel dynamic balance again. It is also necessary to check the tire pressure. The following are the reasons for an off-center steering wheel: 1. After a period of use, the steering wheel may become off-center, which can be related to tire pressure, tire wear, wear of various chassis components, and wheel alignment. You can first measure the tire pressure on both sides. When the tire pressure on both sides is inconsistent, the vehicle will tend to drive towards the side with lower pressure. If the tread wear on the two front tires is inconsistent, it can also cause the vehicle to pull to one side. 2. If there are no issues with the tires, it is recommended to visit a 4S store to check the condition of the chassis components. Changes in wheel alignment values can also cause the steering wheel to become off-center after a period of use. Additionally, it could be due to the tie rod shifting to one side, resulting in an off-center steering wheel.
15
3
Share

How to Remove Snow from a Car

First, start the car and turn on the heater to blow warm air onto the front windshield. Then, use a brush or towel to remove the snow. If there is ice, residues can be cleared using tools like an ice scraper or plastic scraper. Only after the snow is mostly removed and the ice on the windshield has melted should the wipers be used normally. Below is information on removing snow from cars: 1. The first scenario is loose snow. Loose snow refers to the layer of snow that falls on the car's surface without an underlying layer of ice. This type of snow is the easiest to remove. Use a soft cloth or a gentle broom to sweep the loose snow away, always moving in the same direction. Never activate the wipers before clearing the snow. Snow on the car body doesn’t need to be removed immediately—if it’s loose snow, it will naturally melt away once the car is started. 2. The second scenario involves a thin layer of ice beneath the snow. This situation is more challenging to handle. First, do not use the wipers. If the ice layer on the glass is thick, use a rubber or hard glass scraper to gently scrape it off, preferably moving in one direction. Specialized snow removers are now available for better results. Additionally, use a soft broom to gently scrape the side mirrors in one direction until the ice fragments are removed. 3. The third scenario is when the car is covered in thick frost and ice. Some car owners might be tempted to use warm water to melt the ice, but this method is not advisable as it can deform the windshield and wipers or even damage the wipers directly. For thick ice layers, it’s recommended to use professional antifreeze windshield fluid sprayed onto the glass, followed by a rubber scraper to remove the ice. In most cases, the ice will slide off on its own. The same method can be used to remove ice from other parts of the car. Starting the engine and setting the air conditioning to heat, with the airflow directed to the "windshield" setting, can also help remove ice more easily.
13
0
Share

Can ETC be installed on the black area of the car's front windshield?

The ETC device can be installed on the black dotted area of the windshield, as long as it does not obstruct the driver's view and can sense the toll station's detection equipment. However, installing it on the black dotted area of the windshield also has drawbacks, such as reduced solar charging capability of the ETC device, which may lead to power depletion over time. For small cars, the ETC is generally installed in the upper middle part of the front windshield, while for large vehicles like trucks and buses, the installation position is in the lower middle part. The suitable installation position should be no lower than 1.2 meters and no higher than 2.5 meters, with an installation angle between 30 to 90 degrees. For vehicles with built-in or aftermarket explosion-proof film, which may affect the signal transmission of the microwave communication link, the ETC should be installed in the microwave skylight band. Here are some considerations for installing ETC: Do not obstruct the view; it's best to install it behind the rearview mirror: Many car models have windshields with a large rearward tilt angle, which can reduce the driver's field of vision. If this is not considered when installing the ETC, it may increase the driver's blind spots. Installing it on the right side behind the rearview mirror can help avoid obstructing the view. Do not interfere with charging: The ETC electronic tag consumes power but generally does not require charging or battery replacement because it has a solar panel on the back for self-charging. Therefore, during installation, avoid the black dotted areas of the windshield and positions that may block the solar panel. Once installed, do not remove it arbitrarily: The button in the middle of the adhesive is an anti-removal rod connected to a switch. After the electronic tag is installed, the windshield will press the anti-removal rod in. If the tag is removed arbitrarily, the rod will pop out and trigger the switch, locking the electronic tag and rendering it unusable. In such cases, you will need to visit an ETC service point to unlock it. This mechanism is designed to prevent multiple vehicles from sharing one device. When using ETC, note the following: The ETC transaction sensing range is 8 meters. To prevent issues caused by the ETC device of the vehicle in front, maintain a distance of more than 10 meters from the vehicle ahead to avoid automatic payment for the preceding vehicle. The ETC lane recognition speed is 20 kilometers per hour. Driving too fast may result in failure to read the vehicle's device information, leading to payment failure. When using a debit card linked to ETC, insufficient balance may also cause payment failure.
1
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.