What is the normal tire pressure for the X-Trail?

2 Answers
VonVincent
07/24/25 9:42am
The standard tire pressure for the Nissan X-Trail is between 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and reduced by 0.1 bar in summer. The high-end models of the Nissan X-Trail are equipped with a tire pressure monitoring and warning system, which can be viewed on the dashboard. While driving, the tire pressure monitoring system automatically monitors the tire pressure and displays the specific values. For other models, external instruments must be used to check the tire pressure. It is recommended to inspect the tire appearance and pressure before long-distance driving. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes at the bottom, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure. The system typically alerts when the pressure is below 1.8 bar or above 3.0 bar. In such cases, the tires need to be checked and the pressure adjusted. The tire pressure monitoring system has not been reset. After inflating the tires, if the tire pressure is not reset promptly, the system may still record the previous data, causing the indicator light to turn on. Simply resetting the tire pressure will resolve this issue. The tire pressure sensor is damaged. The tire pressure sensor, which monitors the tire pressure, is installed inside the tire and connected to the tire inflation valve. If the sensor is damaged during driving (e.g., by hitting an object), the tire pressure warning light may also illuminate. In case of sensor damage, the only solution is to replace it with a new component.
Was this review help?
12
0
Share
DeFernando
08/11/25 4:57am
I've been driving my X-Trail for five years and always pay special attention to tire pressure during maintenance. The normal range is generally between 2.2 to 2.5 bar, depending on the model year and tire type. You can find the exact value on the label by the car door or in the manual. In hot summers, I adjust it to the lower limit of 2.2 bar, and in cold winters, I increase it slightly to avoid underinflation or overinflation. Too high pressure can make the ride bumpy and damage the car, while too low pressure significantly increases fuel consumption and poses safety risks. Before daily drives, I make it a habit to check with an affordable tire pressure gauge—it only takes a few minutes. Remember, regular checks can save fuel and extend tire life. My experience suggests checking once a month is the safest bet.
Was this review help?
16
2
Share
Expand All
More Forum Discussions

What car has tires that are 3.75 meters tall?

Having tires that are 3.75 meters tall is the Northern Heavy Duty TR100. Here are the specific details about the tires: 1. Tire function: Tires support the entire weight of the vehicle, bear the load of the car, transmit traction and braking torque, ensure the adhesion between the wheels and the road surface, reduce and absorb the vibrations and impact forces during driving, prevent severe vibrations and early damage to car components, adapt to the high-speed performance of the vehicle and reduce driving noise, ensuring safety, handling stability, comfort, and energy efficiency. 2. Tire maintenance methods: Tire maintenance methods include regularly cleaning stones from the tire treads, reducing exposure to sunlight, frequently checking tire pressure, paying attention to suspension maintenance, regularly inspecting front wheel alignment, and being mindful of driving habits.
19
1
Share

Will the Transmission Get Waterlogged After Wading?

Wading can cause water to enter the transmission. Here are the specific details about the transmission: 1. Definition: The transmission mainly refers to the vehicle's gearbox, which is divided into manual and automatic types. A manual transmission primarily consists of gears and shafts, achieving speed and torque changes through different gear combinations. An automatic transmission (AT) is composed of a torque converter, planetary gears, a hydraulic torque variation system, and a hydraulic control system, achieving speed and torque changes through hydraulic transmission and gear combinations. 2. Maintenance Methods: Correctly replace the transmission fluid. A better method is dynamic fluid replacement, which uses specialized transmission cleaning equipment to fully circulate the old fluid during operation, drain it completely, and then add new transmission fluid, achieving a replacement rate of over 90% and ensuring good results. Check the automatic transmission fluid level properly. The method for checking automatic transmission fluid differs from engine oil. Engine oil is checked when the vehicle is cold, while transmission fluid needs to be preheated to about 50°C. Then, after shifting the gear lever through each position for 2 seconds and placing it in park, the fluid level on the dipstick should be between the maximum and minimum marks. If it is insufficient, add the same quality fluid promptly.
16
3
Share

Can Wet Dual-Clutch Transmissions Wade Through Water?

Wet dual-clutch transmissions can wade through water, but it's important to pay attention to the water depth. Here are some precautions for using wet dual-clutch transmissions: 1. Avoid stomping on the accelerator in traffic jams: When driving a car with a dual-clutch transmission, if you encounter a traffic jam or need to stop at a traffic light, try to avoid stomping on the accelerator. This can cause the transmission to shift gears frequently, not only creating a jerky sensation but also causing the transmission to overheat too quickly, potentially leading to damage. 2. Press the brake pedal firmly or shift to N gear when temporarily stopping: When temporarily stopping, the brake pedal should be pressed more firmly. If the waiting time is long, you can also shift directly to N gear. If your foot slips on the brake, it might cause the transmission to remain in a semi-engaged state.
11
5
Share

i for intake or e for exhaust?

I stands for intake, which means IN in English, referring to the air entering the engine. E represents exhaust, also the first letter abbreviation of the English word for exhaust. Below are specific details about automotive exhaust pipes: 1. Overview: The exhaust pipe is part of the engine's exhaust system, which mainly includes the exhaust manifold, exhaust pipe, and muffler. Typically, the three-way catalytic converter, which controls engine pollutant emissions, is also installed in the exhaust system. Exhaust pipes generally consist of a front pipe and a rear pipe. 2. Function: For the vehicle's body, the exhaust pipe serves to reduce vibration and noise, as well as extend the lifespan of the exhaust and muffler system. Its working principle involves diverting airflow through multiple channels, where these divided streams rub and collide with each other, gradually reducing the airflow's velocity. This cycle repeats, ultimately allowing the exhaust gases to be emitted through the vehicle's exhaust pipe, thereby reducing noise and achieving the daily noise reduction effect for automobiles.
20
2
Share

What is the Road and Bridge Ticket During Vehicle Inspection?

Road and bridge tickets during vehicle inspection are mandatory fees that must be paid during the use of a vehicle after it has been registered. Below are specific details about vehicle inspection: 1. Definition: The annual vehicle inspection process refers to the fixed procedure that motor vehicles must undergo each year. It is a mandatory test for every vehicle, equivalent to a physical examination for the vehicle, aimed at promptly eliminating potential safety hazards. 2. Notes: If all items pass at once, the process takes about 2 hours; the compulsory traffic insurance policy must be valid; bring all necessary documents and files that might be needed; do not forget to bring the triangular warning sign and fire extinguisher; if the vehicle body has been modified or has non-compliant stickers, please clean them up before going for the annual inspection.
17
3
Share

Is solid color paint 1k or 2k?

Solid color paint is 1k. Below are specific details about solid color paint: 1. Difference from metallic paint: Metallic paint gets its name from the metal powder mixed in it. Not only does metallic paint make the painted surface appear dazzling, but due to light refraction, the car color and even its outline can change when viewed from different angles. Cars that appear reflective under sunlight generally use metallic paint. Another reason many car enthusiasts commonly choose metallic paint is that the addition of metal powder increases the hardness of the paint, making the surface harder, more wear-resistant, and less prone to scratches, whereas solid color paint does not have this effect. 2. Application: Suitable for the surface protection of metals, wood, plastics, and building exteriors, it can also be used as a surface protection and decorative coating for epoxy, polyurethane, acrylic series, and other paints.
18
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.