What is the normal tire pressure for a Mercedes-Benz?

1 Answers
LeKing
07/30/25 7:39am
According to the requirements and regulations of the international GBT2978-2008 standard, the tire pressure for Mercedes-Benz vehicles is: 2.2-2.5 bar. In winter, the tire pressure should be adjusted slightly higher than the standard tire pressure by about 0.2 bar. In summer, the lower limit of the standard tire pressure is generally sufficient. For example, the lower limit for standard tires is 2.4 bar. If the car is often parked outdoors, the tire pressure can generally be about 0.1 bar lower than the standard to avoid tire blowouts due to high temperatures. There are three commonly used methods for tire pressure monitoring: Direct tire pressure monitoring: Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire pressure. The pressure information is transmitted wirelessly from inside the tire to a central receiver module, which then displays the tire pressure data for each tire. The system automatically alerts when the tire pressure is too low or there is a leak. Indirect tire pressure monitoring: When the pressure in a tire decreases, the weight of the vehicle causes the rolling radius of that tire to become smaller, making it rotate faster than the other wheels. By comparing the differences in rotation speed between the tires, the system monitors the tire pressure. Indirect tire pressure alert systems essentially rely on calculating the rolling radius of the tires to monitor pressure. Tire Pressure Monitoring System (TPMS) introduction: It combines the advantages of the two systems mentioned above. Direct sensors are installed in two diagonally opposite tires, and a 4-wheel indirect system is also equipped. Compared to using only direct systems, this hybrid system can reduce costs and overcome the limitation of indirect systems, which cannot detect when multiple tires simultaneously have low pressure. However, it still cannot provide real-time data on the actual pressure in all four tires as a direct system can. system.
Was this review help?
17
1
Share
More Forum Discussions

Does Tire Sealant Damage Wheel Hubs?

Tire sealant can damage wheel hubs as it may cause corrosion. Principle of tire sealant repair: The liquid containing short fiber materials or fine particles is pre-injected into the tire in a certain amount. When the tire has tiny holes, they will be blocked; when there is a hole in the tire, the escaping air will release the liquid along with the fibers or particles. Usage duration: It can only be used for 6 months. Tire sealant can chemically react with the inner rubber of the tire and the wheel hub, and prolonged use may corrode the steel rim and rubber. Additionally, the sealant injected into the tire may only adhere to one side of the tire wall, affecting the tire's balance, causing vehicle vibration during driving, and compromising vehicle stability.
16
5
Share

How long does it take to check traffic violations in Xi'an?

Generally, after receiving an on-site parking ticket from the traffic police, the violation can be checked within about 3 to 7 days, and it will not exceed 13 working days at the latest. If no illegal parking record is found after about 13 days, you can inquire at the traffic police department. Self-service violation handling: Users can self-process non-on-site traffic violation records with a single fine of 200 or less and cumulative points less than 12 for themselves and up to 3 bound non-personally owned vehicles; self-pay fines for traffic violations issued by officers on-site; self-process traffic violation records for personally owned vehicles and up to 3 bound non-personally owned vehicles; and handle non-on-site traffic violation records nationwide for personally owned vehicles and bound non-personally owned vehicles.
20
0
Share

What engines does Geely use?

Different Geely models are equipped with different engines. The engine model specification is JLH-3G15TD, with the 1.4T engine delivering a maximum power of 104kW and peak torque of 235Nm, while the 1.5T engine offers a maximum power of 130kW and peak torque of 255Nm. Another engine model specification is JLY-4g15, with a maximum power of 80kW, maximum horsepower of 109, and maximum torque speed of 140N.m. Geely's engines are independently developed by Geely Automobile Company, so they are classified as domestic engines. For daily maintenance of Geely's engines, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional devices in the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly based on usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, it may rupture the filter element or bypass the safety valve, carrying contaminants back to the lubrication area, accelerating engine wear and increasing internal pollution. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates properly but also extends the overall lifespan of the radiator and engine.
5
1
Share

What is the fuel tank capacity of HOWO?

HOWO tractors have fuel tanks with different specifications such as 380 liters and 500 liters, depending on the specific model. Fuel tank capacity: The capacity measures the amount of fuel a vehicle can carry. The size of the fuel tank is directly related to the vehicle's fuel consumption. Generally, a full tank can cover more than 500 kilometers. For example, a vehicle with a fuel consumption of 10 liters per 100 kilometers usually has a fuel tank capacity of around 60 liters. Fuel tank capacity display: Drivers often estimate the fuel tank capacity based on when the fuel warning light comes on, but this method is not entirely accurate. Due to various factors such as road conditions and driving conditions, the remaining fuel capacity when the warning light flashes may vary each time.
10
0
Share

Some Small Tips for Car Repair Through Insurance

Experience with car repair through insurance: Insurance companies have a time limit for damage assessment, requiring them to assess the damage within 48 hours; otherwise, the repair invoice will be used as the basis. Considerations for car repair include: Check if it's within the warranty period: If the vehicle is within the warranty period at a 4S shop, repairs should be done there to ensure the user benefits from the warranty policy. If the vehicle is out of warranty, consider going to auto repair centers or similar places, which are cheaper than 4S shops and have lower labor costs. Negotiate the price before repair: 4S shops have fixed prices with no room for negotiation, while other repair shops allow price discussions. Before repairs, clarify the parts to be repaired and the labor costs to avoid unexpected additional charges during the process.
13
3
Share

What are the gear shifting techniques for the Benelli 302s?

Gear shifting techniques for the Benelli 302s: Use the appropriate gear for driving: Many novice drivers tend to drive at low speeds, which results in low vehicle speed but high engine RPM, covering less distance per unit of time and consequently increasing fuel consumption. It is recommended that once the vehicle starts, unless it is in a cold state, the gear should be shifted up to the appropriate level as soon as possible. Generally, higher gears are more fuel-efficient than lower gears. Shift gears step by step: Gear changes should only be done step by step, such as from first to second gear, second to third gear, etc., and not by skipping gears. Skipping gears can cause discontinuous power delivery, leading to stalling. However, downshifting can be done by skipping gears, and driving techniques often require frequent skip-downshifting. Shift quickly and smoothly: The key to shifting gears is speed—completing the actions of depressing the clutch, shifting gears, and pressing the accelerator as quickly as possible. When shifting gears, the clutch must be fully depressed, and gear changes should only occur within a certain speed range.
10
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.