What is the normal temperature for car air conditioning?

Where is the cabin air filter located in the Zotye T600?

The cabin air filter of the Zotye T600 is located beneath the glove compartment on the passenger side, near the left side where there is a rectangular removable panel. Due to the multiple slots, a screwdriver can be inserted into the gap to slowly pry it open when removing. When taking out the old cabin air filter, observe the shape of the filter housing edge to ensure the new filter is installed in the correct orientation. Below is additional information about the cabin air filter: 1. The cabin air filter should be replaced every 10,000 to 20,000 kilometers. When the air conditioning is turned on, outside air enters the vehicle, and the cabin air filter absorbs a large amount of dust and impurities. If the filter is not replaced for a long time, its filtration performance will decline, significantly affecting the driving experience and interior hygiene. 2. Due to the limitations of the manufacturing materials, the cabin air filter cannot be cleaned with water, as a large amount of moisture can render the filter unusable. To clean it, use an air gun to blow out the dust from the opposite side. When cleaning, wear gloves, a mask, and eye protection to prevent dust and debris from entering your body.

2

1

Share

Where is the washer switch located on the old Buick GL8?

The washer switch on the old Buick GL8 is located on the control lever on the right side of the steering wheel, which is a long rod with a round head, also known as the wiper switch. How to use the washer switch: Pull the wiper lever toward the driver's position to clean the front windshield; turn the rear wiper of the old Buick GL8 to the corresponding position, activate the wiper, and push the wiper lever toward the front of the car to spray water and clean the rear windshield. Adjust the settings according to the actual weather conditions; also use the knob in the center of the lever to adjust the sensitivity of the rain-sensing wipers. Precautions when using the washer switch: It is recommended to regularly inspect and clean the wiper blades. Use a towel dampened with alcohol to wipe along the edge of the wiper blades to remove accumulated dirt, debris, and dead leaves, ensuring they remain clean at all times; check the rubber strip for cracks, wear, and unevenness. If the wear is not particularly severe, the owner can use sandpaper to smooth out any uneven surfaces.

3

Share

Does a New Car's Chassis Being Scraped and Producing Abnormal Noise Have Any Impact?

New car chassis being scraped and producing abnormal noise has minimal impact and can continue to be used. However, it is necessary to inspect components such as the vehicle's exhaust pipe and catalytic converter. Composition of a Car's Chassis: A car's chassis consists of four parts: the transmission system, the running gear, the steering system, and the braking system. The chassis functions to support and install the car's engine and its various components and assemblies, forming the overall shape of the car. It also receives power from the engine to enable the car to move and ensure normal operation. Composition of the Transmission System in a Car's Chassis: The transmission system in a car's chassis generally consists of a clutch, gearbox, universal transmission device, main reducer, differential, and half-shaft. The transmission system can be categorized into mechanical transmission, hydraulic transmission, hydrostatic transmission, and electric transmission based on the different methods of energy transfer.

20

2

Share

What materials are needed for renewing a driver's license after expiration?

To renew a driver's license after expiration, you need to prepare two one-inch photos, a medical examination certificate, your ID card, and the original driver's license. One of the photos should be affixed to the top right corner of the medical examination form, while the other will be used for the new license. Then, bring your ID card and driver's license to the licensing hall, fill out the renewal application form, submit the documents along with the medical examination certificate and renewal application form to the staff, pay the fee, and wait to receive your new license. Before renewing, check if there are any outstanding traffic violations. If there are, they must be resolved first; otherwise, the vehicle management office cannot process the renewal. You can start the renewal process up to 90 days in advance. It's important to schedule the renewal properly to ensure it's completed before the original license expires. Typically, the renewal is processed on the spot, but in some cities, it may take a few days to complete the necessary procedures. Once done, you will be notified to collect your new driver's license.

6

1

Share

Does a Spare Tire Well Belong to a Salvage Car?

A spare tire well does not belong to a salvage car. Only if the damage to these parts causes severe impairment to the car's performance can it be considered a salvage car; otherwise, it is not classified as such. Definition of a Salvage Car: A salvage car refers to a vehicle that has suffered damage due to non-natural wear accidents, resulting in a decline in mechanical performance and economic value. Generally, a "salvage car" refers to a vehicle with structural damage. Additionally, water-damaged cars and fire-damaged cars fall under the category of "special salvage cars." Methods to Check for Rear-End Collisions: Minor rear-end collisions are one of the common accidents during vehicle operation. To check for rear-end collision history, open the engine hood and inspect the edge seals of the hood for smoothness and firmness. If the seals are uneven or feel soft to the touch, it indicates that the hood has been repaired.

14

5

Share

What to Pay Attention to When Buying an Imported Car?

When buying an imported car, you need to pay attention to: 1. The Goods Import Certificate, which includes the car name, customs declaration company, chassis number, engine number, production date, etc.; 2. The Inspection Sheet for Imported Vehicles, stamped by the national CIQ inspection and quarantine bureau; 3. The Compulsory Product Certification Vehicle Conformity Certificate, with the conformity certificate on the front and the environmental protection list on the back; 4. The Environmental Protection List; 5. The invoice, which states the vehicle's invoiced price and taxpayer information. The procedures for obtaining temporary license plates for an imported car: Bring the identity documents of the vehicle owner and agent, proof of vehicle origin, the whole vehicle factory qualification certificate for domestically produced vehicles or the import certificate for imported vehicles, vehicle identification code, and engine number rubbing mold procedures to the vehicle management office. When applying, specify the starting and ending locations of the vehicle's travel and the duration of temporary license plate use. After review by the management personnel and passing the vehicle safety technical performance inspection, temporary license plates will be issued, with the validity period and travel locations signed. New cars using temporary license plates must not exceed 15 days, and the owner should promptly apply to the vehicle management authority for official license plates.

5

2

Share

What is the normal temperature for car air conditioning?

Where is the cabin air filter located in the Zotye T600?

Where is the washer switch located on the old Buick GL8?

Does a New Car's Chassis Being Scraped and Producing Abnormal Noise Have Any Impact?

What materials are needed for renewing a driver's license after expiration?

Does a Spare Tire Well Belong to a Salvage Car?

What to Pay Attention to When Buying an Imported Car?

What is the difference between 150 and 140 torque?

What are the reasons for the black screen on the Beijing BJ40 central control screen?

Does the Buick GL8 come with a built-in dash cam?

How to Steer the Wheel When Making a U-turn in Driving Test Part 3?