What is the normal negative pressure for the EA888 engine?

1 Answers
MasonDella
07/24/25 5:36pm
EA888 engine negative pressure is normally between 80-100. Below is the relevant introduction: 1. Introduction: The Volkswagen EA888 engine is a newly designed engine by Volkswagen, integrating advanced technologies such as direct fuel injection, turbocharging, and variable valve timing, achieving a balance between power and economic environmental protection. 2. Displacement: (1) 1.8TSI maximum power is 118kw (160PS)—5000-6200rpm, maximum torque is 250Nm—1500-4500rpm. (2) 2.0TSI maximum power can reach 147kw (200PS)—5100-6000rpm, maximum torque is 280Nm—1700-5000rpm.
Was this review help?
6
0
Share
More Forum Discussions

Which car brand is WEY?

WEY is an SUV brand under Great Wall Motors Co., Ltd., with product lineups including VV7, VV6, VV5, and the new energy series VV7 PHEV. Taking VV7 as an example: The exterior dimensions are 4760mm in length, 1931mm in width, and 1655mm in height, with a wheelbase of 2950mm. The VV7 is equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 227, a maximum power of 167 kW at 5500 rpm, and a peak torque of 387 N·m available from 1800 to 3600 rpm.
6
0
Share

What is the 0-100 km/h acceleration time of the Honda URV370?

The 0-100 km/h acceleration time of the Honda URV370 is 8.45 seconds. Fuel consumption calculation per 100 km: Fuel consumption per 100 km refers to the average fuel consumption of a car when driving on the road. For example, 10 divided by 100 equals 60 divided by 600 on the left side of the equation. Theoretically, driving 100 kilometers consumes 10 units of fuel. On the right side of the equation, the car drives 600 kilometers and consumes 60 units of fuel. The equation holds true. 0-100 km/h acceleration test: Manufacturers usually indicate the official 0-100 km/h acceleration time in the vehicle's promotional materials, but the actual test results often differ from the official figures. This is because different environmental temperatures, road conditions, vehicle wear conditions, and even the amount of remaining fuel in the tank can affect the test results. Therefore, there are no two identical acceleration test results.
17
1
Share

What to Do When the Key Chip is Lost and the Car Won't Start?

The traditional mechanical key is hidden inside the key fob. Simply flip the safety switch, pull out the spare key, and insert it into the keyhole to unlock the door. After shifting into 1st gear, slowly release the clutch to use the wheel's rotation to drive the engine flywheel. However, this is a last-resort method and should not be used frequently.
16
4
Share

What is the method for removing and installing car rearview mirror glass?

First, moisten the position where the small round mirror adhesive is attached with alcohol. Then use the hot air setting of a hair dryer to blow on it, without worrying about whether the heating will damage the glass. After blowing with hot air for a while, the small round mirror will fall off, and the remaining adhesive can be gently wiped off with alcohol to ensure that the rearview mirror is not damaged.
20
3
Share

How to Remove the Bumper of Changan Eado?

Changan Eado is a compact sedan under Changan, with a body length of 4730mm, width of 1820mm, height of 1505mm, and a wheelbase of 2700mm. It is equipped with a 7-speed dual-clutch transmission, delivering a maximum power of 116 kW and a maximum torque of 260 N·m, with a top speed of 200 km/h. The method to remove the bumper of Changan Eado is as follows: 1. Remove the clips connecting the fender liner and the front bumper; 2. Remove the two self-tapping screws connecting the fender and the surround; 3. Pull the bumper forward by bending both sides to detach it, then disconnect all electrical connectors.
16
4
Share

How to Adjust the Screen Brightness of a Mercedes-Benz?

Hold down the adjustment button on the instrument panel. When the LCD screen displays TRIPB, release the adjustment button. Turn on the small light or headlight switch of the combination switch. At this point, continue holding the adjustment button without releasing it. The backlight brightness will start to adjust, cycling through the brightest, normal, and darkest states. Release the button once the desired brightness is achieved. After completing the adjustment, press the adjustment button again to switch the odometer display from TRIPB to ODO.
12
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.