What is the motor power of the Lingtu Kone?

2 Answers
JordanMarie
07/24/25 2:23am
The motor power of the Lingtu Kone is 61 horsepower and 131 horsepower, with two horsepower versions available. The 61 horsepower version has a maximum motor power of 45 kW and a maximum torque of 170 Nm, while the 131 horsepower version has a maximum motor power of 96 kW and a maximum torque of 230 Nm. The Lingtu Kone is a pure electric compact SUV and a single-motor model. It uses ternary lithium batteries across the entire lineup, which are commonly used in most pure electric vehicles and plug-in hybrid vehicles. The front suspension of the Lingtu Kone employs a MacPherson independent suspension, and the rear suspension uses a trailing arm non-independent suspension.
Was this review help?
18
5
Share
DelArcher
08/10/25 10:01pm
Honestly, I have quite some insights to share about the Lynk & Co Kone's motor power. This model typically comes with a power output ranging between 150 to 180 kilowatts, depending on which version you purchase—the higher trim delivers stronger performance. A higher power rating delivers an exhilarating acceleration experience, especially that thrilling push-back feeling during takeoff. However, greater power also means faster battery drain, so remember to ease off the accelerator pedal in daily driving to preserve battery life. For maintenance, it's recommended to inspect the motor cooling system every six months to prevent overheating and power loss. Among the daily driving modes, the Eco mode is well-tuned for energy efficiency, while the Sport mode squeezes out more horsepower. When tackling hills or overtaking, ample power makes things much easier and enhances safety reliability. Understanding the official specifications is key.
Was this review help?
1
5
Share
Expand All
More Forum Discussions

Which is more fuel-efficient for the JH6, empty, half-loaded, or fully loaded?

Empty loading is more fuel-efficient for the FAW JH6, but road conditions and driving habits can also cause more deviations in fuel consumption. Below are the factors affecting fuel consumption and methods to reduce it: Factors affecting fuel consumption: There are many factors that affect fuel consumption, including driving conditions, driving habits, engine displacement, vehicle load, etc. However, the fuel consumption during normal driving usually falls within a certain range. Methods to reduce fuel consumption: Shift gears promptly: Driving in low gear for extended periods not only results in slower speeds but also increases fuel consumption, especially when driving on slopes. The shorter the time taken to shift gears, the more fuel you can save. Reduce idle time: When driving on urban roads, you often encounter long red light waits. In such cases, turning off the engine can help save fuel. Drive at an economical speed: The economical speed for most cars is between 60 km/h and 80 km/h. Fuel consumption is at its lowest when the car operates within this speed range.
8
3
Share

What is the battery capacity of the Model 3 Standard Range?

Tesla Model 3 Standard Range has a battery capacity of 55kWh. Below are the battery lifespan and usage precautions: Battery lifespan: Generally, automotive batteries have a lifespan of 2-3 years, while the original battery in a new car can last over 3 years. Battery usage precautions: Therefore, if a battery has been in use for about two years, you should be cautious as its lifespan is nearing its end. At this point, frequent inspections should be conducted, with early detection to identify and resolve issues or replace the battery promptly. This helps avoid sudden "failure" of the battery during use, which could lead to losses. After replacing the battery, note that new batteries, including the original ones in brand-new cars, may not be fully charged (not 100%). Thus, after installing a new battery or purchasing a new car, it is advisable to run the engine for a longer period to ensure the battery is fully charged.
13
3
Share

What is the p115e Ford fault?

p115e Ford refers to a fault that occurs when the powertrain control module has reached the maximum allowable correction range. Causes of powertrain control module failure: Excessive carbon deposits in the intake system and at the root of the intake valve, resulting in an excessively lean air-fuel mixture during cold starts; severe dirt on the throttle body, leading to insufficient air intake; the starter motor's speed does not meet the required level. Functions of the powertrain control module: The powertrain control module can provide users with various services, including digital data leased line services with rates ranging from 2M to 155M, as well as other services such as voice, image transmission, and distance learning. It is particularly suitable for users who require high data transmission rates and greater bandwidth.
9
2
Share

Why does the Q5 make noise when braking at low speeds?

The reasons for the Q5 making noise when braking at low speeds are as follows: Brake pad break-in: Brake pad break-in is an important part of the break-in process for new cars. Typically, after driving a few hundred kilometers, the braking will feel more comfortable. Sand particles entering: While driving, very small sand particles may get between the brake pads and discs, sometimes causing noise due to friction. Brake system malfunction: Missing or damaged brake disc fixing screws, or the need for additional lubrication, can cause brake noise. Severe brake disc wear: Abnormal brake disc wear can occur due to a dirty brake disc surface, uneven material density of the brake disc, excessively high operating temperatures, or mismatched installation torque of the brake disc.
5
1
Share

Why can't the interior light of the Jeep Cherokee be turned off?

There are generally three reasons why the interior light of the Jeep Cherokee cannot be turned off. One is a short circuit in the interior light wiring, another is that the door is not properly closed. The last possible reason is that the reading light is set to the always-on mode. Setting the reading light to the middle position will turn it off when the door is closed. Method to turn off the interior light: You can adjust the time for the light to turn off after the engine is shut off in the settings of the central control screen. It is best to turn off the air conditioning and headlight assembly before shutting off the engine. After parking, be sure to turn off the car lights and other electrical devices in the vehicle. Interior light: The interior light in passenger cars is usually installed in the center of the interior. It should ideally illuminate the entire interior evenly. Additionally, the light switch (SW) should be positioned so that both the front and rear seats can operate it. The SW generally has three positions: ON, OFF, and linked to the door. To reduce the thickness of the light, a 5-10W tubular bulb is often used. To meet the lighting requirements of a spacious interior, the bulb power typically ranges from 8-30W.
4
4
Share

What is the fuel consumption of the VV5 2.0T?

The fuel consumption of the Wey VV5 2.0T model is 7.1 liters per 100 kilometers. Below are the reasons for high fuel consumption and tips to reduce it: Reasons for high fuel consumption: Piston or piston ring damage, leading to oil burning and incomplete fuel combustion. New drivers often keep the accelerator pedal pressed without lifting it, neglecting to vary their speed, which inadvertently increases fuel consumption. Aging machinery or faults in the computer control system. Damage to the fuel tank or fuel lines, resulting in fuel leakage. Tips to reduce fuel consumption: Master the clutch pedal operation through practice, ensuring smooth and steady movements. Develop good habits: press the clutch fully and release it slowly. Coordinate the accelerator and clutch properly. Start by engaging first gear, slowly releasing the clutch while adding throttle at the semi-clutch point, and fully release the clutch only after the car starts moving.
18
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.