What is the motor power of the Elantra New Energy?

2 Answers
VanJoshua
07/24/25 3:42pm
This car's motor has a maximum power of 44.5kw. Below is the relevant information about the Elantra: 1. The Elantra New Energy is a single-motor model, with a maximum torque of 170 Nm for its motor. The Elantra New Energy is a plug-in hybrid vehicle that uses lithium-ion batteries. Lithium batteries are widely used and can be found in many cars and electronic products. 2. The Elantra New Energy features a MacPherson independent suspension at the front and a multi-link independent suspension at the rear. The multi-link suspension can improve the wheel's grip. The Elantra New Energy has good fuel economy, with a fuel consumption of approximately 4.0 liters per 100 kilometers.
Was this review help?
12
1
Share
OLouis
08/11/25 8:43am
I've been driving the Elantra PHEV for a while now. Its electric motor typically delivers 43.5 kW, which is about 58 horsepower – pretty standard for a hybrid. The acceleration from standstill is exceptionally smooth, making it perfectly adequate for daily commutes. It offers better range than pure EVs since it's a hybrid. During driving, I've noticed it handles uphill climbs and overtaking without hesitation. I'd recommend regular checks on the battery and motor wiring connections to prevent any looseness that might affect performance. Compared to hybrids in the same class, like Toyota's, the power output is similar, but Hyundai's design is more compact and quieter. Overall, this power setup strikes a good balance between efficiency and performance, making it ideal for city driving.
Was this review help?
4
5
Share
Expand All
More Forum Discussions

Where is the diagnostic connector located on the Peugeot 5008?

The diagnostic connector of the Peugeot 5008 is located inside the cabin. There is an OBD-labeled clip at the diagnostic connector; opening the clip reveals the diagnostic connector interface. The purpose of the car's diagnostic connector is: when the car malfunctions, the fault codes can be read through the car's OBD interface, and then the faults can be analyzed and cleared. Relevant information is as follows: 1. The OBD system continuously monitors whether the car's exhaust exceeds the standard during engine operation and will issue an alert immediately if it does. 2. Initially, the OBD interface was set up only to monitor the car's exhaust emissions, but in recent years, OBD has evolved through several generations, greatly enhancing its functions and roles.
17
4
Share

What are the matching tires for the Geely Boyue?

Geely Boyue comes with two types of tires for high and low configurations, as detailed below: 1. The mid-to-low configuration of Geely Boyue is equipped with Giti tires, with a tire specification of 225/65R17. 2. The high configuration of Geely Boyue features Cooper tires, belonging to the Discoverer series, which are designed for urban SUVs, with a tire specification of 225/60R18. Regarding tire usage, the following three points should be noted: 1. Prolonged driving can wear out tires; good driving habits can ensure the longevity of the vehicle and extend the service life of the tires. 2. During tire usage, regular tire rotation is necessary to ensure even wear and maintain the tires in good working condition. 3. If there is normal wear and tear on the tires during use, timely inspection and replacement of the tires are required.
19
0
Share

What is the normal tire pressure for the Buick Verano?

The normal tire pressure range for the Verano is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and decreased by 0.1 bar in summer. This data complies with the international GBT2978-2008 standard. The Verano's tire pressure monitoring system is indirect, utilizing the vehicle's ABS balance control, and only displays low pressure when there is a leak. To check the tire pressure, first prepare a tire pressure gauge, locate the position of the factory tire pressure label, press the tire pressure gauge against the tire valve to measure and read the value. Remember to replace the valve cap after measuring. Generally, a tire pressure above 2.8 bar is considered too high, and below 2.0 bar is too low. Hazards of overinflated tires: Reduced tire friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overextends the tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of underinflated tires: Increases friction with the road surface, raising fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement of tire components, causing abnormal heat due to excessive rolling; degrades the function of cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the bead area and causing abnormal wear; multiplies friction with the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing strength. High-speed driving may result in a blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes at the bottom, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure: Typically, an alert is triggered below 1.8 bar or above 3.0 bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset in time, the system will still record the previous data, causing the indicator light to stay on. Simply perform a tire pressure reset. Damaged tire pressure sensor: The sensor, installed inside the tire and connected to the inflation valve, monitors tire pressure. If the sensor is damaged during driving (e.g., by impact), the tire pressure warning light will illuminate. A damaged sensor must be replaced with a new one.
11
1
Share

Is an Off-Road Vehicle an SUV?

An off-road vehicle is not necessarily an SUV. The main difference between SUVs and off-road vehicles lies in the specialized functionality of off-road vehicles. Off-road vehicles feature a body-on-frame construction, whereas urban SUVs typically have a unibody construction. Below are detailed explanations of the relevant content: The full English name for an off-road vehicle is Off-Road Vehicle, which is specifically designed for off-road driving. Off-road vehicles can traverse extremely poor road conditions or even areas without roads, combining features such as high ground clearance, body-on-frame construction, four-wheel drive, tires with excellent traction, and substantial horsepower. Vehicles with these characteristics are referred to as off-road vehicles. SUVs are generally categorized into two types: urban and off-road. Some SUVs prioritize off-road capabilities over daily usability and comfort, although they still fall short of professional-grade off-road vehicles. These are commonly referred to as off-road SUVs. The other type, urban SUVs, cater more to the needs of average families, focusing on daily use and leisure, with limited or no off-road capabilities. Therefore, an off-road vehicle is not necessarily an SUV.
20
1
Share

How to Open the Envision Key?

To open the Envision key, follow these steps: 1. Release the lock button at the rear end of the remote key and pull out the mechanical key. 2. Insert a flat-head screwdriver into the gap at the corner and twist to separate the upper and lower parts, thus opening the key. Precautions for using the remote key are as follows: 1. Passengers, especially children, can easily open the door and fall out of the vehicle while it is moving. When the doors are locked, they cannot be opened using the door handle. 2. If the vehicle is unlocked, children inside may not be able to exit on their own. They could suffer from heat exhaustion, permanent injury due to heatstroke, or even death. 3. When slowing down or stopping, people outside the vehicle can easily enter through unlocked doors. Locking the doors helps prevent such incidents.
18
4
Share

How to Check the Oil Dipstick on a BMW X1?

BMW X1 oil dipstick inspection method is as follows: 1. Make sure the vehicle is cooled down. After pulling out the dipstick for the first time, wipe it clean with a clean tissue, then reinsert it. 2. Upon pulling out the oil dipstick for the second time, check the oil level on the dipstick. If the oil level is between the upper and lower limits, it indicates the oil quantity is normal. Relevant information is as follows: 1. The oil dipstick is usually located near the engine and has a distinct feature—a pull ring. You can pull it out by firmly tugging the ring upwards. 2. The total amount of engine oil is approximately four liters. The capacity between the upper and lower limits on the dipstick is roughly one liter. Even if the oil level reaches the lower limit on the dipstick, there are still at least three liters of oil remaining in the engine.
12
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.