···
Log in / Register

What is the model number of the Lavida's reverse light?

3 Answers
LeCamille
09/05/25 4:46am
The model number of the Lavida's reverse light is 1156. The reverse light is installed at the rear of the car to illuminate the road behind when reversing and serves as a warning to vehicles and pedestrians behind. All reverse lights are white. The Lavida is a sedan produced by SAIC Volkswagen, with body dimensions of 4605mm in length, 1765mm in width, and 1460mm in height, a wheelbase of 2610mm, and a top speed of 200km/h. The car's body weight is 1305kg, with front-wheel drive. Available body colors include Mysterious Black, Modest Purple, Sharp Silver, Elegant White, Quiet Brown, Graceful Gold, Stylish Blue, and Sharp Red.
Was this review help?
17
5
Share
LeahLynn
09/17/25 5:14am
As a car enthusiast, I've always been fond of the Lavida. The reverse light model is usually a W16W bulb, which is super common and can be found in abundance on Taobao. I've replaced it myself once. First, you need to open the trunk lid, unscrew the small screws on the light cover, and then you can pull out the old bulb and replace it with a new one. The whole process takes just a few minutes, but you have to be careful not to loosen the battery wires. Reverse lights are particularly crucial as they illuminate the rear blind spot when reversing at night, reducing the risk of scraping the car. If you don't drive often, it's advisable to check if the lights are working every season, so you don't regret it only when stopped by traffic police. LED upgrades are quite popular now, offering higher brightness, energy savings, and affordable prices.
Was this review help?
10
0
Share
Expand All
OElijah
10/31/25 5:45am
Having worked in an auto repair shop for years, I've found that most Lavida's reverse lights use the W16W model, with occasional T15 variants. Confirming this is simple—car owners can check it themselves: lift the trunk lid, unscrew the lamp cover screws, and the bulb will have the model number printed on it. When replacing the bulb, don't rush—turn off the engine first to avoid accidental short circuits. Common issues include broken filaments or aging connectors; dim lights can easily lead to accidents during nighttime reversing. It's best to check them during your six-month maintenance—it saves money and gives peace of mind. Non-functioning reverse lights can result in points deducted during annual inspections, so paying attention to this small detail can prevent bigger troubles.
Was this review help?
8
4
Share
Expand All
More Forum Discussions

What are the causes of tire fires?

Tire fires are mainly caused by three reasons: excessive speed, overloading, and overheating of tires leading to ignition; bearing fires igniting tires; or brake lock-up causing excessive friction that results in spontaneous combustion. Situations requiring tire replacement: Check the tire wear indicators: Regardless of the tire brand, wear indicator marks are set in the groove areas of the tread. When the tread depth has worn down to the level of the raised indicator rubber, it indicates that the tire needs to be replaced. Bulging phenomenon: If the tread bulges, it means the local rubber has deteriorated or there is uneven pressure. In this case, the tire may explode at any time, making continued driving extremely dangerous, so it should be replaced promptly.
20
5
Share

What is the fuel consumption of CB400?

CB400 has a fuel consumption of 4.5 liters per 100 kilometers. Motorcycle fuel consumption calculation: First, record the odometer reading (L1) when the fuel level is high and the fuel supply is cut off. Then, note the amount of fuel added (YL) during refueling. When the fuel level drops to the high level cutoff again, record the odometer reading (L2). Subtract L1 from L2 and divide by YL to get the distance traveled per liter of fuel in actual driving conditions. Factors affecting motorcycle fuel consumption: Low-quality engine oil consumes more than high-quality oil, and lower viscosity oil consumes more than higher viscosity oil. Engine temperature plays a significant role - low-speed high-load conditions and long-distance travel can cause excessive engine temperature, dramatically increasing oil consumption. Oil consumption also varies based on the engine's internal structure and lubrication method. Engines with more oil passages, higher pressure, and multi-point injection tend to have higher oil consumption.
7
4
Share

What is the typical fuel consumption of a 150cc motorcycle?

On average, a 150cc motorcycle consumes about 3 liters of fuel per 100 kilometers. Below is a partial introduction regarding fuel consumption: Introduction: Generally refers to the gasoline consumption per 100 kilometers, which is a theoretical indicator for vehicles. Methods to reduce fuel consumption: The longer the idling time when parked, the greater the fuel consumption, so try to minimize idling time; avoid rapid acceleration, slamming the throttle, and driving at low RPMs. Factors affecting fuel consumption: Various working conditions such as acceleration, deceleration, braking, and engine idling, as well as load capacity, temperature, and whether the air conditioning is on, all have an impact.
15
1
Share

What does the Cruze P0016 fault code mean?

The Cruze P0016 fault code indicates a malfunction in the crankshaft or camshaft position sensor, which is related to a problem in the post-catalyst fuel system. First, check if the timing belt is broken or has skipped teeth. Then, inspect whether the solenoid valve that adjusts the valve timing is damaged. It is also necessary to check if the oil pressure is normal, and then realign the timing. The crankshaft converts the up-and-down motion of the pistons into rotational motion. The camshaft controls the opening and closing of the valves. The electronic control unit continuously monitors the variable camshaft's timing position and checks the relative position between the camshaft and the crankshaft. If the relative position is misaligned by more than one tooth, the P0016 fault code will appear. Possible causes include a malfunction in the camshaft position sensor or its circuit, a malfunction in the crankshaft position sensor or its circuit, a faulty engine speed sensor, contaminated oil, a stuck variable camshaft solenoid valve, etc. After troubleshooting the vehicle, the fault code must be cleared. When clearing the fault code, it is essential to strictly follow the specific vehicle model's designated fault code clearing procedure. Under no circumstances should the method of disconnecting the battery's negative terminal be used to clear the fault code.
5
0
Share

Is the CVT transmission of the CRV durable?

The CVT transmission of the CRV is durable. CVT transmission offers good comfort: Since there are no manual or automatic transmission gears, but instead two steel belts that drive the system by changing the transmission radius on the conical wheels to alter the gear ratio, there is no traditional gear-shifting process. This naturally eliminates the jerking sensation during gear shifts, achieving linear power output and smoother driving. CVT transmission has excellent performance: Due to the linearization of power output, the engine's working state is more easily matched with the vehicle's load and speed, achieving a balance between fuel consumption, exhaust emissions, and the performance of the engine and transmission. CVT transmission's fuel-saving performance: It can maintain the optimal gear ratio at all times, improving mechanical transmission efficiency and fuel economy. The steel belt transmission components have a simple structure and are highly controllable, with current technology achieving high reliability and service life.
10
1
Share

What to Do When MG GS ABS and Dynamic Stability System Malfunction?

Solutions for MG GS ABS and dynamic stability system malfunctions are introduced as follows: 1. If under warranty, the car can still be driven, but the ABS is ineffective, so drive slowly. 2. If out of warranty, it's best to remove all four tires and clean the ABS thoroughly, as oil contamination may be the cause. Additional information on ABS system response during emergency braking: 1. During emergency braking, the ABS system allows the wheels to maintain a state of rolling and sliding. 2. When the ABS system is active, the ABS indicator on the dashboard will flash. 3. If the ABS system malfunctions, the ABS indicator on the dashboard will remain lit. 4. If the ABS system malfunctions, do not continue driving; resume driving only after repairs. 5. Continuing to drive with a malfunctioning ABS system poses significant safety hazards.
9
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.