What is the mnemonic for the lighting test in Subject 2?

2 Answers
LeAniyah
07/24/25 1:37pm
Subject 2 lighting test mnemonic is as follows: Pay attention to turn signals in Subject 2, remember them well and don't forget; don't rush when starting the ignition, turn on the left turn signal in sequence; when exiting parallel parking, and also during right-angle turns; only proceed when the left signal is on, and don't forget the hill start! Below is additional information about Subject 2: 1. Subject 2 content: Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment, referred to as the field driving skill test. The test items for cars C1 and C2 include reversing into a parking space, parallel parking, stopping and starting on a slope, right-angle turns, and curve driving (commonly known as S-turns) as the five required tests (some areas also include a sixth item, high-speed card collection). 2. Teaching objectives: Master the basic driving operation essentials and possess the basic ability to control the vehicle; proficiently master the basic methods of field and on-site road driving, possess the ability to reasonably use vehicle control components and correctly control the spatial position of the vehicle, and be able to accurately control the vehicle's driving position, speed, and route.
Was this review help?
7
0
Share
ColinAnn
08/11/25 7:37am
I still remember the light mnemonic for the Subject 2 driving test—simple and easy to recall: ‘Turn on, high beam, low beam, flash twice, turn off.’ ‘Turn on’ means switching on the headlights, ‘high beam’ is shifting to high beams, ‘low beam’ is switching back to low beams, ‘flash twice’ simulates alternating lights for overtaking, and ‘turn off’ means shutting off the lights. This mnemonic helped me pass on my first try. During driving school practice, the instructor emphasized that each action must be completed within 10 seconds, and the sequence couldn’t be mixed up. Making a mistake, like using low beam before high beam, would immediately deduct points on the test. In real-world driving, the mnemonic proves even more useful—adjusting lights at night to avoid accidents. Light operation may seem minor, but it’s crucial for safety. Practicing until it becomes muscle memory is key.
Was this review help?
13
2
Share
Expand All
More Forum Discussions

What Causes the Abnormal Noise in a Manual Transmission Clutch?

Manual transmission clutch abnormal noise can be caused by clutch pressure plate failure or broken clutch components. Clutch pressure plate failure: The clutch is part of the car's transmission system, fixed between the engine and the gearbox, serving to disconnect or connect the engine to the gearbox. The clutch pressure plate is mounted on the engine flywheel, with the clutch disc located between the pressure plate and the flywheel. If the clutch disc is severely worn, abnormal noise will occur when using the clutch. Broken clutch components: Broken clutch pressure plate springs or broken clutch pressure plate release levers.
7
3
Share

Where is the VIN code located on a car?

The VIN code on a car is located under the front windshield on the driver's side and consists of 17 characters. The VIN code, also known as the Vehicle Identification Number, contains information such as the vehicle's manufacturer, year, model, body type and code, engine code, and assembly location. The overall rules for the VIN code prohibit certain characters: O, Q, I, and 0. The letter Z is invalid in the year position. The ninth digit can only be a number from 0 to 9 or the uppercase letter X. The last four digits must all be numbers and cannot be letters. Owners can use the VIN standard and vehicle configuration for analysis. Digits four to eight represent the engine and transmission model, which must match the information on the assembly label without any discrepancies.
14
0
Share

What are the reasons for severe engine shaking in a sedan?

There are four main reasons for severe engine shaking in a sedan: 1. Ignition system failure. Solution: Check if the spark plugs have excessive carbon buildup, and clean or replace them immediately if necessary. 2. Worn or loose engine mounts. Solution: Replace the engine mounts. 3. Carbon deposit issues. Solution: It is recommended to take the car to a 4S shop for engine cleaning. 4. Poor fuel quality. Solution: Clean the car's throttle body promptly. If the issue persists, take the car to a 4S shop for repair. Always refuel at reputable gas stations, use the fuel grade specified by the manufacturer, and perform regular maintenance.
4
3
Share

How to Reset the Vehicle Maintenance Indicator Light?

To reset the vehicle maintenance indicator light, follow these steps: 1. First, set the odometer to the trip state; 2. Turn off the ignition switch; 3. Hold down the odometer toggle button; 4. Turn on the ignition switch (without engaging the start position). The purpose of the vehicle maintenance indicator light is to record the mileage of important components, similar to a timer in a sprint race, serving as a reminder for both the vehicle owner and maintenance personnel. The original intention of the maintenance light is to remind the owner to perform maintenance as soon as possible. When this light comes on, the owner should promptly visit a 4S shop for maintenance. After the maintenance is completed, the 4S shop will use a diagnostic tool to reset the maintenance light.
5
0
Share

What Causes the Engine Light to Illuminate in a Newly Purchased Car?

Newly purchased car engine light illumination is caused by: unclean fuel leading to contamination or blockage of the fuel supply system. Currently, some vehicles are equipped with exhaust emission monitoring systems. As these control systems can very sensitively detect vehicle exhaust emissions and fuel cleanliness conditions, the use of unclean fuel can cause contamination in the fuel supply, ignition, and emission systems, leading to the engine malfunction indicator light illuminating and varying degrees of engine vibration. An effective solution is: after thoroughly cleaning the contaminated system, consistently add gasoline with stable performance indicators and a quantitative amount of fuel system cleaner, and the situation will improve.
18
3
Share

Is It Useful to Install an Engine Guard Plate?

Installing an engine guard plate is useful as it can protect the engine and chassis. If the car frequently travels on roads with poor conditions, it is necessary to install an engine guard plate. Engine guard plates can be divided into four types based on their materials: steel, aluminum alloy, plastic-steel, and plastic. The most commonly used type on cars is the aluminum alloy underguard plate, which offers significant protective effects. The engine guard plate is an engine protection device designed for various car models. Its primary purpose is to prevent mud from covering the engine, which could lead to poor heat dissipation. Additionally, it helps prevent engine damage caused by impacts from uneven road surfaces during driving, thereby extending the engine's service life.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.