What is the mirror in the car called?

2 Answers
EllieLee
07/28/25 9:54pm
The mirror inside the car is called the rearview mirror. Below are the usage methods for the rearview mirror: 1. Before driving, adjust the position and angle of the rearview mirror. During driving, due to vehicle vibrations, the position and angle of the rearview mirror may change. Pay attention to this and adjust it promptly. 2. When performing maneuvers such as parking, starting, overtaking, turning, or making a U-turn on regular roads, always give the appropriate signal and make sure to observe the rearview mirror to stay informed about the traffic conditions on both sides and behind you. 3. When passing through narrow roads or bridges with non-motorized vehicles or pedestrians on either side, slow down and pay appropriate attention to the rearview mirror. Maintain a necessary lateral distance from non-motorized vehicles or pedestrians. 4. When driving on highways, not only should you maintain a safe distance from the vehicle in front, but you should also use the rearview mirror to observe and judge the following distance of vehicles behind you. This ensures you are well-prepared when handling situations to avoid rear-end collisions.
Was this review help?
6
1
Share
AnnieRose
08/12/25 2:30am
I've been driving for twenty years, and there are several types of mirrors in a car: the one in the center of the windshield is called the rearview mirror, mainly used to check the traffic behind to avoid rear-end collisions; the ones on the left and right doors are called side mirrors, specifically for scanning blind spots to help with safe lane changes; the vanity mirror inside the sun visor is often used by women but isn’t a priority. These mirrors are collectively referred to as the rearview system, and their maintenance is simple—just clean them regularly and avoid obstructions. Always adjust the angles properly before driving; I check their positions every time I get in the car. Safe driving relies heavily on them, so never overlook them. In rainy or foggy conditions with poor visibility, these mirrors help you anticipate dangers and reduce accidents. An experienced driver’s wisdom: keeping the mirrors clear is keeping your life safe.
Was this review help?
18
5
Share
Expand All
More Forum Discussions

Is the Envision Equipped with Full-Time Four-Wheel Drive?

The Envision is equipped with full-time four-wheel drive. Below is an introduction to the Envision: 1. Vehicle Exterior: As a next-generation strategic model of General Motors, the Buick Envision inherits the design essence of the ENVISION concept car, featuring a dynamic, elegant, and imposing overall styling. The front end adopts the family-style vertical chrome grille, complemented by wing-shaped intelligent xenon headlights, boomerang-shaped LED daytime running lights, and streamlined exterior rearview mirrors, creating a sharp and dynamic visual effect. The body features a full-frame chrome window design and an aluminum roof rail that follows the roofline, paired with industry-leading 19-inch large aluminum alloy wheels, delivering a striking visual impact. 2. Vehicle Specifications: Built on General Motors' global next-generation platform, the Buick Envision boasts impressive dimensions with a length, width, and height of 4667mm × 1840mm × 1659mm, and a wheelbase of 2750mm, providing consumers with a spacious interior. The new model is powered by the award-winning 'Ward's 10 Best Engines' next-generation 2.0T intelligent direct-injection turbocharged engine, delivering a maximum power output of 191kW and a maximum torque of 353Nm. It is paired for the first time with a next-generation intelligent 6-speed transmission featuring Start/Stop technology, ensuring quicker and smoother gear shifts for seamless power delivery and significantly reduced fuel consumption in urban driving conditions.
20
4
Share

What is the difference between MAX A/C and A/C?

MAX and A/C are both buttons located near the car's air conditioning system. A/C stands for air conditioning (cooling), while MAX represents maximum settings, whether for cooling temperature or fan speed. In summer, when using the air conditioning, you need to press the A/C button to activate the compressor for cooling. In winter, when adjusting the air conditioning temperature for heating, you should turn off the A/C button; otherwise, heating will not function. Air Conditioning System: Modern cars are equipped with air conditioning systems, which consist of ventilation, heating, cooling, air purification devices, and control systems. For cooling, the system relies on the compressor. On car buttons, red typically indicates heating, while blue represents cooling. Some car air conditioning systems also feature an AUTO button, which stands for automatic temperature regulation. Pressing this button will automatically adjust the car's air conditioning to the most comfortable temperature for the human body. Fan Speed Adjustment: If there is no AUTO button, the driver must manually adjust the temperature and fan speed. When using the air conditioning for cooling, it's best to direct the vents upward because cold air sinks, which helps the car's interior cool down faster. For heating, it's better to direct the vents downward, as warm air rises.
7
0
Share

Will Water Enter the Car if It Submerges the Chassis?

Water submerging the chassis does not necessarily mean water will enter the car. If the water reaches half the height of the wheels, there is generally no issue. The bearings might get wet and rust, but this will not have any immediate impact. Below is an introduction to the relevant water submersion levels: Water reaching half the height of the wheels: If the water reaches half the height of the wheels, and if the car has good sealing, water generally will not enter. However, if the car is soaked for a long time and the sealing is poor, water may enter. After ensuring that the engine's intake system is not flooded, drive the car to a 4S shop to have the soaked interior components removed, cleaned, and dried. Water submerging half the wheels: If the water submerges half the wheels, water may enter the engine and cabin. Do not start the car at this time, as it could cause the electronic devices and components in the car to burn out.
6
4
Share

Can You Drive After 4 Beers in 8 Hours?

It varies from person to person. Drinking four bottles of beer is equivalent to consuming 2000ml of beer. The time it takes to metabolize the alcohol and reach a level where it cannot be detected depends on individual alcohol metabolism rates and physical constitution. For those with efficient alcohol metabolism: Generally, individuals with good physical constitution and efficient alcohol metabolism can fully metabolize the alcohol within 24 hours. However, for those with slower alcohol metabolism and weaker physical constitution, it usually takes longer than 24 hours to completely metabolize the alcohol. The actual time required varies from person to person and cannot be generalized. Relevant regulations: According to China's current drunk driving standards, a blood alcohol content (BAC) of less than 20mg/100ml does not constitute drunk driving. However, a BAC of 20mg/100ml or higher is considered drunk driving, and a BAC of 80mg/100ml or higher is classified as severe drunk driving.
13
1
Share

What brand is the sfg15ta engine?

sfg15ta engine adopts the technology of Fiat Automobile Company and is produced by Chongqing Xiaokang Power Co., Ltd., belonging to a domestic engine. Models like Fengon 500 and Fengon S560 are equipped with the sfg15ta engine. The Fengon 500's engine model is sfg15ta, with a maximum power of 110kW, maximum torque of 220 Nm, and maximum horsepower of 150. Daily maintenance methods for the sfg15ta engine include: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's requirements; Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, causing various problems for the engine. To avoid faults, change the oil regularly according to usage conditions and maintain an appropriate oil level; When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, it may burst the filter element or open the safety valve, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination; Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear; Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
4
2
Share

What is the wading depth of the Lynk & Co 03?

The wading depth of the Lynk & Co 03 is approximately 300mm. The wading depth of the Lynk & Co 03 is determined by the height of the vehicle's chassis, which corresponds to the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when driving through waterlogged roads. Therefore, in terms of safe wading depth, off-road vehicles and SUVs have obvious advantages. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake of the Lynk & Co 03 is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it can cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth must not exceed the height of the engine's air intake. Alternatively, installing a snorkel can increase the height of the engine's air intake, thereby improving the maximum wading depth. If wading is unavoidable, the following safe and correct procedures should be followed: Before driving through water, always turn off the auto start-stop function to prevent the engine from automatically restarting if the vehicle stalls in the water, which could lead to severe engine damage due to water ingress. Assess the underwater road conditions based on the passage of vehicles ahead and choose an appropriate entry point. Follow the path taken by other vehicles and drive at a low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, observe warning water level markers, trees, or other reference points like the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Be aware of your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not proceed and choose an alternative route instead.
11
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.