What is the minimum ground clearance of the Volkswagen Tiguan chassis?

2 Answers
ParkerMarie
09/01/25 7:08am
The minimum ground clearance of the Volkswagen Tiguan chassis is 180mm. The minimum ground clearance refers to the distance between the lowest point of the car (excluding the wheels) and the supporting plane when the car is fully loaded or stationary, which is used to indicate the car's ability to pass over obstacles such as rocks and tree stumps without collision. The Tiguan is a compact 5-door, 5-seat SUV with body dimensions of 4506mm in length, 1809mm in width, and 1685mm in height, with a wheelbase of 2684mm. The Tiguan is equipped with a 1.8T turbocharged engine and a 6-speed automatic transmission, delivering a maximum power of 118 kW and a maximum torque of 250 Nm. It features front-wheel drive, with a front suspension using MacPherson independent suspension and a rear suspension using multi-link independent suspension.
Was this review help?
2
2
Share
DonovanFitz
09/14/25 2:57am
The Volkswagen Tiguan has a minimum ground clearance of approximately 200mm, which is quite suitable for daily driving. I often commute with this car, and the chassis rarely scrapes against speed bumps or small potholes in the city, reducing concerns about underbody damage. The advantage of an SUV lies in this level of ground clearance. If you occasionally drive on rural dirt roads or in rainy areas, this height can prevent water from entering the engine, enhancing safety. However, it's important to note that the height may slightly decrease when the vehicle is fully loaded, as the suspension system compresses. Therefore, it's best to regularly check the chassis condition and ensure proper tire pressure to prolong component lifespan. When encountering uneven roads, it's advisable to slow down and drive smoothly to minimize wear. Overall, 200mm is a reasonable design value.
Was this review help?
11
5
Share
Expand All
More Forum Discussions

Difference Between Turbo and Naturally Aspirated Engines

Differences between naturally aspirated and turbocharged engines: 1. With the same displacement, turbocharged engines deliver more power than naturally aspirated ones. 2. Maintenance costs for turbocharged engines are higher than for naturally aspirated engines. 3. Under the same displacement, turbocharged engines are more fuel-efficient at high-speed conditions. 4. The manufacturing cost of turbocharged engines is higher than that of naturally aspirated engines. Below are the principles of turbocharging: 1. A turbocharger is essentially an air compressor that increases engine intake by compressing air. 2. It utilizes the inertial force of exhaust gases to drive the turbine in the turbo chamber, which in turn drives the coaxial impeller. The impeller compresses and delivers air from the air filter pipe, pressurizing it before it enters the cylinder. 3. As engine speed increases, the exhaust gas expulsion speed and turbine speed also increase synchronously. The impeller then compresses more air into the cylinder. The increased pressure and density of the air allow for more complete fuel combustion. By correspondingly increasing the fuel quantity and adjusting the engine speed, the engine's output power can be enhanced.
14
4
Share

What Causes Misfire in Three Cylinders Due to Catalytic Converter Damage?

When encountering misfire in three cylinders due to catalytic converter damage, the reasons may include the following: Ignition Fault: It is necessary to check the ignition coil and high-voltage wires. The ignition coil cannot be repaired and must be replaced if faulty. Fuel Injection Fault: This could be caused by wiring issues or poor fuel injection pressure. Human Operational Errors: Such as carelessness or mistakes during maintenance: faults caused by disturbances, loose connectors, etc. Wear and Aging: Delayed maintenance or the use of substandard, unqualified, or non-compliant engine oil. Engine Fault: If the engine is faulty, it needs to be replaced promptly.
14
5
Share

How to Deal with Sunroof Noise on Bumpy Roads?

Solutions for sunroof noise on bumpy roads are as follows: First, remove accumulated dust from the sunroof tracks, then apply lubricant to both sides of the tracks, especially focusing on areas where noise is detected. Be careful not to apply lubricant outside the tracks. Tighten any loose screws and regularly clean the tracks; replace the sunroof sealing strip in a timely manner and try to avoid exposure to rain and direct sunlight. Below are precautions for using a sunroof: 1. When opening the sunroof, ensure there are no obstacles on the roof that could hinder its upward or backward movement, as this may overload and damage the motor or accidentally scratch the sunroof glass surface. 2. Always operate the sunroof correctly when opening or closing it, as improper operation can cause excessive current in the motor, leading to motor damage. 3. It is best not to open the sunroof when driving on extremely bumpy roads, as this may cause excessive vibration between the sunroof and the tracks, potentially deforming related components and damaging the sunroof when opened. 4. Avoid directing high-pressure water jets directly at the sunroof's sealing strip during car washing, as this can deform the strip and cause leaks.
4
4
Share

Noises During Driving Process

Unusual noises during driving are usually caused by damages to parts such as doors and sunroofs. Daily maintenance should be paid attention to. Below are the relevant details: Common Causes of Noises: Noises from doors; Noises from sunroof; Noises from dashboard; Noises from chassis. Solutions for Noises: For door noises, tighten the screws; For sunroof noises, clean the tracks or replace the rubber seals; Check the dashboard; Repair the chassis. Benefits of Regular Vehicle Maintenance: Ensures optimal vehicle performance; Enhances driving safety; Reduces engine noise; Extends vehicle lifespan.
13
4
Share

Do You Need to Return to Neutral When Shifting from 1st to 2nd Gear?

When shifting from 1st to 2nd gear in a car, there's no need to return to neutral. Simply hold the gear lever and pull it downward into 2nd gear directly. Here's relevant information: Gear Allocation: A typical automatic transmission car has six gear positions arranged from top to bottom as: P, R, N, D, S, L. Automatic Principle: The engine's power is transmitted through the transmission, which is also a key factor affecting fuel consumption. Generally, automatic transmissions consume over 10% more fuel than manual transmissions. Whether manual or automatic, more gears usually mean better fuel efficiency.
2
1
Share

Can Test Drive Vehicles Be Purchased?

Test drive vehicles can be purchased as long as the purchase procedures are complete and the test drive vehicle can be transferred. In the automotive sales market, 4S stores provide test drive vehicles for customers to experience in order to help consumers better understand the performance and comfort of the intended purchase before buying. The following are the pros and cons of test drive vehicles: 1. Advantages of test drive vehicles: The original vehicle quality is generally good, usually high-end models, and any existing issues should have been exposed during test drives, with most odors already dissipated. 2. Disadvantages of test drive vehicles: They are already used cars and suffer more severe wear and tear in areas like interior, brakes, and tires compared to similar used cars. Therefore, the final decision should be based on the price, and sufficient price advantages should be considered.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.