What is the minimum ground clearance of the Vision X6?

2 Answers
DelCalvin
07/28/25 11:25pm
The minimum ground clearance of the Vision X6 in an unloaded state is 30CM on both sides of the vehicle. The smallest ground clearance is at the factory-installed plastic guard under the engine, measuring 17.7CM. Below is some related information about the Vision X6: 1. The Vision X6 is the same as the Vision SUV, just different names for the same model. Vision SUV is the final name given at launch, while names like Vision X6 and Vision GX7 were temporary. 2. There are three powertrain options: a 1.4T inline 4-cylinder turbocharged engine, with the high-power version paired with either a 6-speed manual or CVT transmission, delivering a maximum power of 104KW and maximum torque of 235N·m; the low-power version is paired with a CVT transmission, producing a maximum power of 98KW and maximum torque of 215N·m. There is also a 1.8L inline 4-cylinder naturally aspirated engine, matched with a 5-speed manual transmission, offering a maximum power of 98KW and maximum torque of 170N·m.
Was this review help?
8
2
Share
VonAaron
08/12/25 3:48am
I remember the minimum ground clearance of the Vision X6 is around 200mm, which is quite suitable for daily driving. Having driven many SUVs, this height makes it much easier to navigate small potholes or speed bumps in the city, reducing the risk of scraping the undercarriage. When driving on dirt roads in the suburbs, it can handle basic road conditions well and has decent wading capability, though it's not meant for hardcore off-roading. If heavily loaded with cargo or passengers, the clearance might decrease slightly, so it's advisable to regularly check tire pressure and keep the undercarriage clean to avoid mud buildup affecting its off-road performance. Overall, this design makes the Vision X6 an economical and practical urban SUV, ideal for family trips or daily commutes.
Was this review help?
10
3
Share
Expand All
More Forum Discussions

Does touching the line in the S-curve during Subject 2 result in failure?

Yes, it results in failure. In the Subject 2 driving test, apart from not stopping properly on the steep slope or forgetting to signal, which deducts 10 points for each occurrence, other violations such as touching the line or the vehicle body being scanned by the line will directly result in a failure. Here are the solutions to avoid touching the line in the S-curve: 1. Entrance: There are two directions for the entrance: left entrance and right entrance. For a left entrance, the vehicle should stay close to the right line before turning the steering wheel to the left; for a right entrance, the opposite applies—the vehicle should stay close to the left line before turning the steering wheel to the right. This accounts for the inner wheel difference to prevent the rear wheels from touching the line during the turn. 2. During the drive: While driving, keep the front of the vehicle aligned with the edge line. When turning left, align the front with the right edge line; when turning right, align it with the left edge line. 3. Exiting the S-curve: There are two directions for exiting the S-curve: left exit and right exit. For a left exit, when the front wheels are just about to leave, turn the steering wheel half a circle to the right to prevent the rear wheels from touching the line; for a right exit, do the opposite—when the front wheels are just about to leave, turn the steering wheel half a circle to the left to prevent the rear wheels from touching the line.
11
2
Share

How Many Kilometers Should Conventional Oil Be Changed?

Engine oil should be changed every 5,000 kilometers or once a year, whichever comes first. This interval can be appropriately extended or shortened based on different driving environments, driving habits, and other factors. Engine oil, also known as motor lubricant, serves multiple functions such as lubrication and wear reduction, auxiliary cooling, sealing and leak prevention, rust and corrosion protection, and shock absorption. The steps for changing engine oil are as follows: 1. Run the engine until it reaches operating temperature. Then use a jack to lift the vehicle, engage the handbrake, and secure the front wheels with wooden wedges; 2. Drain the oil by locating the oil drain plug underneath the vehicle. Unscrew the plug to allow the oil to flow out. Observe the oil color—normal oil should be translucent. If it appears black, it should be replaced promptly; 3. Remove the oil filter. When the oil flow slows, unscrew the oil filter for secondary drainage. Removing the oil filter can be challenging and requires a specialized filter wrench. Ensure all residual oil is drained from the compartment; 4. After fully draining the oil, replace the oil filter. Use the filter wrench to install the new filter and tighten it. Then secure the drain plug and lower the vehicle; 5. Pour new oil into the oil filler port. Select the appropriate oil for your vehicle and the correct volume based on engine displacement. After pouring, remove the dipstick to check if the oil level is sufficient. Avoid overfilling—moderation is key; 6. Start the engine and listen for any unusual noises. Then check the dipstick again to ensure the oil level is neither overflowing nor below the minimum mark.
5
2
Share

Can an automatic transmission car move when in D gear without pressing the accelerator?

An automatic transmission car can move when in D gear without pressing the accelerator, but it will move slowly. Below are the precautions and driving methods when starting the car: Precautions when starting the car: After the engine starts and before the car moves, do not press the accelerator pedal; when shifting gears, do not release the brake pedal; after starting, do not press the accelerator pedal too quickly or too hard—press it slowly. Driving methods for automatic transmission cars: When starting the engine of an automatic transmission car, the gear selector must be placed in the P or N position, and the handbrake must be engaged or the brake pedal must be pressed. When starting the car, first press the brake pedal, shift into gear, release the handbrake, then smoothly lift the brake pedal, and after the car starts moving slowly, gradually press the accelerator pedal.
2
2
Share

What does it mean when the subject two appointment is being processed?

When the online appointment for the driving test subject two shows as being processed, it means the appointment has not been successfully confirmed yet and is still under review. Below are the rules for the subject two appointment queue: 1. First-time subject two appointment: The queue is ordered based on the time of application acceptance. 2. Successful appointment: If the appointment is canceled due to personal reasons after being successfully scheduled, the queue is ordered based on the cancellation time. 3. Non-first-time appointment: For non-first-time appointments, the queue is ordered based on the time of the last test. 4. Cancellation due to non-personal reasons: If the appointment is canceled due to non-personal reasons (e.g., power outage or network failure at the test site preventing normal completion of the test), the queue order remains unchanged.
6
1
Share

How to turn on the rear speakers in a Buick GL8?

Control the audio system via the steering wheel. Here is additional information about the Buick GL8: 1. Engine: It uses a 2.5L direct-injection naturally aspirated engine, replacing the older 2.4/3.0L naturally aspirated engines. 2. Fuel Consumption: With features like direct injection and start-stop technology, the GL8-25S shows significant improvement in fuel efficiency compared to the older models, achieving an overall 16% reduction in fuel consumption. 3. Comparison: The throttle response is similar to that of the 2.4L model, with good initial acceleration performance. The throttle is quite responsive at low to medium RPMs, and the overall power output is comparable to the 28T model.
1
5
Share

Where is the trunk switch located inside the Škoda Octavia?

Škoda Octavia does not have a separate trunk unlock button. The central locking button next to the cigarette lighter and the unlock button on the remote key can both open the trunk, marked with an icon of an open car trunk. You can also press the area directly below the brand logo when the vehicle is unlocked to open the trunk. Here is some extended information about the Škoda Octavia: 1. Body dimensions: The Octavia measures 4675 mm in length, 1814 mm in width, and 1460 mm in height, with a wheelbase of 2686 mm. 2. Engine: The Octavia is equipped with three engine options: a 1.5L naturally aspirated engine, a 1.2L turbocharged engine, and a 1.4L turbocharged engine. 3. Front and rear suspension: The Octavia features a McPherson independent front suspension and a torsion beam non-independent rear suspension.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.