What is the minimum ground clearance of the MG HS?

1 Answers
VonAnthony
07/29/25 9:47am
The minimum ground clearance of the MG HS is 175mm. Minimum ground clearance refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the car is fully loaded and stationary. It is used to characterize the vehicle's ability to pass over obstacles such as rocks and tree stumps without collision. The MG HS is a compact SUV launched by SAIC Motor, with body dimensions of 4574mm in length, 1876mm in width, and 1664mm in height, and a wheelbase of 2720mm. The MG HS is equipped with 1.5T and 2.0T engines, with maximum power outputs of 169 horsepower and 231 horsepower respectively. The transmissions paired with these engines are a 7-speed dual-clutch and a 6-speed dual-clutch gearbox respectively.
Was this review help?
5
4
Share
More Forum Discussions

Is the Shaking Issue in Mercedes-Benz C260L Normal?

Mercedes-Benz C260L shaking issue is not normal. The causes of shaking may include excessive carbon deposits, fuel supply system failure, aging engine mounts, or engine misfire. The Mercedes-Benz C260L belongs to the Mercedes-Benz C-Class series. Below are detailed introductions about the Mercedes-Benz C-Class: 1. Overview: The Mercedes-Benz C-Class is the best-selling model in the family and offers the most comprehensive lineup among all Mercedes-Benz series. The C-Class sedan is equipped with an active safety system, intelligent lighting system, preventive safety system, passenger safety protection system, and rescue tools. 2. Others: The wheelbase is 2760mm. The vehicle dimensions are 4581mm*1810mm*1448mm. The trunk volume is 475L. The fuel consumption is 7.7-9 liters/100km. The fuel tank capacity is 66L. The standard seating capacity is 5. The top speed is 223-245km/h. The acceleration time is 7.6-9.1 seconds (0-100km/h).
18
1
Share

What is the fuel consumption of the imported Explorer?

Ford Explorer's minimum fuel consumption ranges between 10.01L/100km~11.6L/100km, while the maximum fuel consumption ranges between 13.21L/100km~15.06L/100km. Constant-speed fuel consumption: Refers to the fuel economy indicator when a vehicle travels at a constant speed on good road surfaces. The fuel consumption at 90Km/h and 120Km/h serves as the main evaluation criteria for fuel economy. The fuel consumption per 100 kilometers stated in domestic vehicle manuals is generally constant-speed fuel consumption. However, since vehicles often experience various driving conditions such as acceleration, deceleration, braking, and engine idling in actual driving, constant-speed fuel consumption tends to be lower and significantly different from actual fuel consumption. Road cycle fuel consumption: Is a fuel economy indicator measured when a vehicle drives in repeated cycles according to specified speeds and time norms on roads, also known as multi-condition road cycle fuel consumption. The Society of Automotive Engineers (SAE) established the SAEJ10926 road cycle test specification, which is widely adopted. This specification includes four different cycles: urban, suburban, interstate (55Mile/h), and interstate (70Mile/h).
19
1
Share

What shade of green is the Cullinan green?

The Cullinan green is a vivid green. The Rolls-Royce Cullinan has recently introduced eight new colors, including bright red, Selby grey, Paradiso blue, dark olive, peacock blue, forged yellow, vivid green, and magenta. These eight new color options are now available for pre-order in the U.S. market. Introduction to the Cullinan: The Rolls-Royce Cullinan is the second model to feature Rolls-Royce's aluminum luxury architecture and the brand's first SUV. The Cullinan's luggage compartment is separated from the cabin by a single piece of glass, making it the industry's first 'three-box' SUV. It is powered by a specially modified 6.75-liter V12 twin-turbocharged engine, delivering 563 horsepower. Interior Design: The interior features a combination of leather, real wood, and metal accents. The overall design is similar to the Phantom, but the steering wheel is thicker yet smaller in size. Rolls-Royce states that the Cullinan is a driver-oriented model, with a greater emphasis on the driving experience. The new all-digital instrument cluster adopts a three-dial design, complemented by virtual dials and pointers.
3
5
Share

What are the causes of the start-stop system error in the Nissan Tiida?

The causes of the start-stop system error in the Nissan Tiida are insufficient battery power and throttle valve malfunction. Introduction to the battery: The car battery, also known as a storage battery, is a type of battery that works by converting chemical energy into electrical energy. The car battery acts as a voltage stabilizer for the vehicle's electrical system, mitigating impact voltages in the electrical system and protecting the electrical equipment in the car. Introduction to the throttle valve: The throttle valve is a controllable valve that regulates the entry of air into the engine. After entering the intake pipe, the air mixes with gasoline to form a combustible mixture, which then burns to perform work. It is connected to the air filter at the top and the engine block at the bottom. There are two types of throttle valves: traditional cable-operated and electronic. In traditional engines, the throttle valve operating mechanism works via a cable or rod, connecting the accelerator pedal to the throttle linkage plate. Electronic throttle valves primarily use a throttle position sensor to control the opening angle of the throttle valve based on the engine's energy requirements, thereby regulating the amount of air intake.
5
5
Share

What is the reason why the Baojun 510 transmission fails to engage gears?

Baojun 510 transmission failure to engage gears may be caused by gear lever failure, incomplete clutch disengagement, or pressure plate failure. The following are specific details: 1. Gear lever failure: The positioning parts of the gear lever's positioning ball head lose function, allowing the gear lever to rotate freely around its own axis and making it impossible to accurately control the gear position; it may also be that the spherical working surface at the lower end of the gear lever is worn out, preventing the gear lever from controlling the fork or the groove of the fork head, making both gear engagement and disengagement impossible. 2. Incomplete clutch disengagement: The gear shifting mechanism of the transmission works normally. This fault can be eliminated by adjusting the clutch or replacing some clutch parts to ensure that the clutch has appropriate free clearance and separation clearance. 3. Pressure plate failure: Pressure plate failure may also cause the inability to engage gears. Many cars experience heavy clutch and difficulty in shifting gears when hot, mostly due to prolonged wear of the pressure plate or aging of the separation fingers, which requires replacing the pressure plate.
10
1
Share

What is the method for resetting the front brake pads on a BMW 3 Series?

The method for resetting the front brake pads on a BMW 3 Series involves first replacing the sensor wire, then using a diagnostic computer to perform the reset. Introduction to brake pads: Brake pads are the components that are pressed against the brake disc or drum when the brake is applied. In a car's braking system, brake pads are the most critical safety components, as they play a decisive role in the effectiveness of braking. Good brake pads act as protectors for both the driver and the vehicle. Brake pads are generally composed of a steel plate, an adhesive heat insulation layer, and a friction block. The quality of braking performance is largely determined by the brake pads. Based on the composition of the friction material, brake pads can be categorized into the following types: asbestos brake pads, semi-metallic brake pads, low-metallic brake pads, NAO formula brake pads, ceramic brake pads, and NAO ceramic brake pads. Precautions for front brake pad reset: After pressing the brake pedal, the master cylinder generates thrust to push the hydraulic fluid into the wheel cylinders for reset. Before resetting, it is essential to confirm the replacement of the rear brake pads and the sensor wire. The sensor wire must be replaced to perform the reset; otherwise, maintenance data errors may occur.
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.