What is the minimum ground clearance of the Chevrolet Orlando?

2 Answers
Rodger
07/29/25 4:42am
The minimum ground clearance of the Orlando is 180 millimeters. The minimum ground clearance refers to the distance between the lowest point of the vehicle (excluding the wheels) and the supporting surface when the vehicle is fully loaded and stationary, which is used to characterize the vehicle's ability to pass over obstacles such as stones and tree stumps without collision. Here is some related information about the Orlando: 1. The Orlando is a model officially released by Chevrolet. It has a wheelbase of 2796mm. The second and third-row seats of the Orlando support 4/6 and 5/5 proportional folding respectively. When only the 5-seat configuration is used, the trunk capacity can reach 479L, and the trunk can accommodate two 20-inch suitcases. 2. The fuel standard for the Orlando is 92 or above unleaded gasoline, and its emissions comply with the China VI emission standards. The suspension system (front/rear) consists of MacPherson independent suspension/multi-link independent suspension.
Was this review help?
5
1
Share
VonGiselle
08/12/25 8:22am
I've been driving the Chevrolet Orlando for two years now, and I remember the minimum ground clearance is about 160mm, which is quite practical for city driving. I don't usually worry about scraping the undercarriage when going over speed bumps or small potholes, but I still need to be careful with larger obstacles. I often go on family trips to suburban areas with poorer road conditions, and this height makes the ride feel stable, unlike those low-clearance cars that get uncomfortable with every bump. In the car owner group chat, we've discussed how ground clearance directly affects passability—for example, it can easily handle 50cm deep water during the rainy season. I suggest everyone avoid parking on curbs as it can wear out the protective plates, and just remember to regularly check and clean the undercarriage.
Was this review help?
5
5
Share
Expand All
More Forum Discussions

What is the indicator for an empty fuel gauge

Car no fuel sign is the fuel light comes on. Related introduction: 1. The reason why the fuel indicator light comes on: The amount of fuel is controlled by the float sensor in the fuel tank. After the sensor monitors the fuel level, it feeds this signal back to the ECU, which then conducts a comprehensive analysis and reflects it on the dashboard. If the fuel level is too low, the fuel indicator light will come on. 2. Factors for the fuel indicator light to come on: Fuel level position. The float sensor transmits this information through a simple determination of the liquid level position, which can be said to be related to the shape of the fuel tank to some extent, but this aspect does not vary much among different car models. Recent average fuel consumption. This is mainly a standard considered by the ECU. If driving in the city with frequent stops and starts, the average fuel consumption is higher, then the indicator light will come on earlier; if driving on the highway with lower average fuel consumption, the indicator light will come on later. It is a relatively user-friendly design, and some cars may not be equipped with this function.
17
1
Share

What engine is used in the Mercedes-Benz C200 Coupe?

The Mercedes-Benz C200 Coupe is equipped with two engine options. The 1.6T version delivers a maximum output of 115 kW, with peak torque of 250 Nm and a top speed of 210 km/h. The 2.0T version produces a maximum output of 135 kW, peak torque of 300 Nm, and a top speed of 229 km/h. In terms of safety features, this model comes with front and side airbags for both driver and passenger, knee airbags, tire pressure monitoring, front seatbelt reminder, ISOFIX child seat anchors, ABS anti-lock braking system, brake force distribution, brake assist, traction control, electronic stability program, and autonomous emergency braking.
6
1
Share

What is the function of a car timing belt?

The function of a car timing belt is to ensure synchronization of the engine's operation, including the piston's movement, the opening and closing of valves, and the ignition sequence, all under the coordination of the timing mechanism. The timing belt is a consumable part, and if it breaks, the camshaft will not operate according to the timing, which can lead to severe damage due to the collision between valves and pistons. Therefore, it is crucial to replace the timing belt according to the mileage or time specified by the manufacturer. Being a rubber component, the timing belt, along with its related parts such as the timing belt tensioner, timing belt tensioner pulley, and water pump, will wear out or degrade over time with engine operation. Hence, manufacturers strictly require periodic replacement of the timing belt and its accessories within the prescribed intervals for engines equipped with timing belts.
17
2
Share

Can a Vehicle Pass Annual Inspection After an Engine Replacement?

It is possible for a vehicle to pass the annual inspection after an engine replacement, but the owner must first complete a change registration at the vehicle management office; otherwise, the inspection will not be approved. Below is relevant information regarding the annual inspection of motor vehicles: 1. Relevant Regulations: According to Article 10 of the "Motor Vehicle Registration Regulations": If a registered motor vehicle undergoes any of the following changes, the owner must apply for a change registration at the local vehicle management office: (1) Change of body color; (2) Replacement of the engine. If the engine is replaced without completing the change registration at the vehicle management office, the vehicle will not pass the annual inspection. 2. Required Documents for Engine Change Registration: "Motor Vehicle License", "Motor Vehicle Registration Certificate", "Motor Vehicle Change Registration Application Form", "Motor Vehicle Registration Business Process Record", identity proof of the vehicle owner, proof of engine origin, safety technical inspection certificate, and criminal inspection certificate. The vehicle owner must complete the registration within ten days after replacing the engine.
2
4
Share

Can You Still Drive When BMW Warns of Low Engine Coolant?

When BMW warns of low engine coolant, you should not continue driving. Operating the vehicle with insufficient coolant can lead to elevated engine temperatures, potential engine damage, and reduced engine lifespan. Therefore, when the vehicle alerts you to low coolant levels, it is essential to safely pull over, add coolant promptly, and schedule an inspection and repair at a BMW service center. Coolant should be replaced every 2 to 3 years or every 40,000 kilometers. When selecting coolant, ensure its freezing point is approximately 10 degrees Celsius below the lowest environmental temperature. In addition to its antifreeze properties, coolant also serves functions such as corrosion prevention, boiling resistance, and scale inhibition. The BMW X5 is BMW's first four-wheel-drive SUV model, with dimensions of 4930mm in length, 2004mm in width, 1776mm in height, and a wheelbase of 2975mm.
19
1
Share

How to Turn Off the Taillights of Hyundai Santa Fe?

Method to turn off the taillights of Hyundai Santa Fe: Rotate the light switch to the 'off' position to turn them off. The taillights are activated along with the headlights, so simply turning off the lights will deactivate the taillights. The Hyundai Santa Fe measures 4930mm in length, 1910mm in width, and 1720mm in height, with a wheelbase of 2865mm. In terms of power, the vehicle is equipped with a 2.0-liter turbocharged engine across all variants, delivering a maximum horsepower of 240 HP and a peak torque of 353 Nm. The engine reaches its maximum power output at 6000 rpm, while the maximum torque is available between 1450 to 3500 rpm. The front suspension of the Hyundai Santa Fe features a MacPherson independent setup, and the rear suspension utilizes a multi-link independent configuration.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.