What is the minimum age requirement for driving an electric vehicle?

1 Answers
LukeFitz
07/29/25 10:52am
Driving an electric vehicle requires the individual to be at least 16 years old. Conditions for electric vehicles to be on the road: Electric bicycles must be registered with the traffic management department of the public security authority before they can be driven on the road. It is strictly prohibited for any unit or individual to lend, misappropriate, alter, fraudulently obtain, or forge electric bicycle license plates. The driver of an electric bicycle must be at least 16 years old. When driving on the road, the electric bicycle must maintain its original appearance, and it is not allowed to install canopy frames or modify the power system. Age requirements for applying for other vehicle types: The age for applying for a large passenger vehicle driving license is between 21 and 45 years old; for a large truck driving license, it is between 18 and 50 years old; for a small car or small automatic passenger vehicle driving license, it is between 18 and 70 years old; and for other vehicle types, the age for applying for a learner's driving license is between 18 and 60 years old.
Was this review help?
13
1
Share
More Forum Discussions

Where is the handbrake of the Buick business car?

The handbrake of the Buick business car is located at the far left under the foot. When parking is needed, step on it firmly to the bottom, which gives the same feeling as pulling up the handbrake normally. Just step on it again to release the parking and get back on the road. If the power gear is engaged without releasing the parking, there will be a voice reminder. The specific use of the handbrake is as follows: 1. Remember to pull the handbrake when parking and turning off the engine. If the handbrake is not pulled after parking, the car may move by itself, leading to accidents. Especially on slopes, it is necessary to engage the gear and pull the handbrake, waiting for the vehicle to stabilize before getting off. 2. The handbrake is often used in conjunction with the neutral gear. When waiting briefly at a red light, pulling the handbrake in neutral not only prevents the car from rolling on uneven roads but also allows the right foot to release the brake. 3. Do not pull the handbrake too tight. Nowadays, many cars have spring-operated handbrakes with gears. The higher the handbrake is pulled, the tighter the spring becomes. Therefore, when pulling, it is advisable to stop when the car does not shake, and try not to pull it to the extreme, which helps prolong the life of the handbrake. 4. When starting, make sure to push the handbrake down, and pay attention to pressing the button to ensure it reaches the very bottom. Forgetting to release the handbrake can cause damage to it.
1
5
Share

What to Do If the Buick Car Key is Left in the Trunk?

If the car door is open, you can use the trunk switch on the door to open it. If the car door is locked, you can contact a 4S store to unlock it. There is a trunk unlock button on the driver's side door. If the car door is not locked, simply use this switch to open the trunk. Here is some information about Buick: Introduction: Buick is an automobile brand marketed by General Motors in the United States, Canada, and China. It is sold in North America, China, CIS countries, and the Middle East. Meaning: The pattern resembling "three shields" in the Buick (BUICK) logo serves as its graphic trademark and is the emblem of the Buick division.
9
5
Share

How to Care for Automotive Leather?

First, apply a layer of polish to genuine leather seats. This not only enhances the shine but also adds a protective coating to the seats. This method is relatively simple and can be done by car owners at home (manual scrubbing): For semi-aniline leather jackets, use quick brushing and wiping (mix half a bowl of water with 8 drops of LV cleaner for color protection, then add 20 drops of high-end leather surface cleaner). When cleaning full-aniline leather jackets, start by dampening with water, then brush and wipe simultaneously. The cleaning process for the inner lining of the jacket is the same as for glossy leather jackets.
2
2
Share

How to Remove the Rear Seat of a Magotan?

The method for removing the rear seat of a Magotan is as follows: 1. Locate the fastening clips at the junctions between the left and right seat cushions and the car floor. Insert both hands on either side of the clips and lift upwards with force. 2. After lifting both clips, push the entire seat cushion sharply towards the backrest direction. It can be moved by pushing horizontally, and then the entire cushion can be lifted upwards to remove it. Below is some relevant information about the Magotan: 1. The dimensions of the Magotan are 4866mm in length, 1832mm in width, 1464mm in height, with a wheelbase of 2812mm. 2. The 1.8TSI engine equipped in the Magotan is a new-generation engine from Volkswagen Germany. The new Magotan 1.8TSI and the entire model series adopt the HSB high-strength body structure design, with 74% of the body structure using high-strength and ultra-high-strength steel plates, significantly improving the body structure strength while reducing the body weight.
11
3
Share

Is it better to use 92 or 95 gasoline for the Nissan X-Trail?

Both 92 and 95 octane gasoline can be used for the Nissan X-Trail. Gasoline is a volatile, flammable hydrocarbon mixture liquid obtained from petroleum through distillation and cracking, and can be used as fuel. Here is more information about the Nissan X-Trail: 1. The Nissan X-Trail is a compact 5-door, 5-seat SUV. Taking the 2021 X-Trail as an example, its body dimensions are: length 4675mm, width 1820mm, height 1722mm, wheelbase 2706mm, minimum ground clearance 208mm, and fuel tank capacity 65 liters. 2. The 2021 X-Trail is equipped with a 2.0L naturally aspirated engine, with a maximum power of 111kW and a maximum torque of 194Nm, paired with a CVT transmission.
3
4
Share

What is the reason for the Mercedes GLK300 eyebrow light not working?

Mercedes GLK300 eyebrow light not working may be caused by a power supply failure leading to the entire light not functioning, or external power supply issues (such as poor contact, open circuit, insufficient voltage, etc.). Power supply failure causing the entire light not to work: However, generally LED light beads are connected in series and parallel, so under normal power supply conditions, the entire light usually does not go out completely—only part of it may not light up. External power supply issues: If the light itself is not working, it is generally caused by a power supply failure or an open circuit or damage to the light source. Troubleshooting procedure: Check external factors first, then internal; start with simple checks before moving to complex ones.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.